Advertisement
Quick Links
Cordless Driver Drill
C d p a c i t i c s
-
Stcel
Wood
Wood screw
Equipped with Electric Brake
MODEL 6071D
MODEL 6071DW
With F a s t Charger
MODEL 607lDWK
No load speed
Dimensions IL x W x HI
Net weight
With F a s t Charger a n d Carrying C a s e
INSTRUCTION MANUAL
SPEC IF I CAT IONS
10
11111,
4
5 m m
x
2 0
mini
1
~~
6oo
R , m , n
I
220 m m x 49 mm
x
2 1 5 mm
1 1 5 k g
1 3
a"!
1
13'16" x 3 4"1
(8~518" x 1 7'8"
x
8 1!2"1
1
12 5 Ibs!
Battery Cartridge
7000
1
-
Model DC7100 Fast Charger
Dimensions
IL x W x
HI
Net
1
weight
0 7 kg
O C
1 4 5
m m
x
80 m m
x
61 mni
H r
1
5 0 H r
6 0
H I
~
7 2 V
1
I5
314'' x
3 ~ 1 { 8 "
x
2 3 / 8 " !
A C
orily
1
*
Manufacturer reserves t h e right t o c h a n g e specifications without notice.
*
Note: Specifications may differ from country to country.
Advertisement
Related Manuals for Makita CORDLESS DRIVER DRILL 6071D
Summary of Contents for Makita CORDLESS DRIVER DRILL 6071D
- Page 1 Cordless Driver Drill INSTRUCTION MANUAL SPEC IF I CAT IONS C d p a c i t i c s Wood Wood screw Stcel 5 m m mini 11111, a"! 13'16" x 3 4"1 7000 Model DC7100 Fast Charger Battery Cartridge 5 0 H r Manufacturer reserves t h e right t o c h a n g e specifications without notice.
-
Page 2: Important Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. B e sure switch is OFF when plugging in. 16.
- Page 4 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord 9. Do not operate charger with damaged cord or plug mediately. I O . Do not operate charger if it has received a sharp blow, been dropped, or other- wise damaged in any way;...
-
Page 5: Additional Safety Rules
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1 . Do not charge Battery Cartridge when temperature is BELOW 10°C ( 5 O O F ) ABOVE 4OoC ( 1 0 4 O F ) . 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. - Page 6 Installing or removing battery cartridge 0Always switch off the tool before inser- tion or removal of the battery cartridge. .To remove the battery cartridqe, pull out the set plate on the bottom i f the and grasp both sides while withdrawing from the barrel.
- Page 7 Selecting correct Phillips bit Use the chart to determine the best size driver bit for the size of screw wish use. Selecting slotted bit Use a slotted bit that properly fits the screw slot. Use of a bit t h a t is too small will damage the screw and/or bit.
- Page 8 to stop. CAUTION : Before inserting t..e battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns t o the "OFF" position when released. Reversing switch action This tool has a reversing switch to change the direction of rotation.
- Page 9 Bubble level tool is equipeed with a bubble level to This aid in holding the tool horizontally. Simply center the bubble in the sight window. Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool. tool Start the slowly and then increase the...
- Page 10 Drilling operation Drilling wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. Drilling in metal To prevent the bit from slipping when starting a hole, make a centerpunch and hammer at the point to be drilled.
-
Page 11: Maintenance
Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection T o maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. maintenance. - Page 12 Part 7 4 3 4 0 1 - 6 Foam polishing pad Part N o . 7 4 3 0 2 3 - 2 with your Makita tool specified in this Fast charger Model D C 7 1 0 0 113109-0 Part No.
- Page 13 Battery holster Holster holds extra battery Part N o . 823033-3C Steel carrying case Part N o . 823087-3 (Steel case) Part N o . 181372-3 (Plastic Case) Tool holster has some bits storage space Use holster carry drill o n l y removing bit.
- Page 14 (3/8") CORDLESS DRIVER DRILL Model 6071D Note: The switch and other part configurations may differ from country to country. MODEL 6071D...
- Page 15 MOUEL 6071U 'EM A&, DESCRIPTION Drill Chuck S10 Pan Head Screw M 5 x 1 8 Gear Plane Bearing Motor Holder S w m h Housing Bubble Level Note T h e switch and other speclflcalions part , , ! & I : , ' , "...
- Page 16 ONE YEAR from the date of original purchase. Should any troubkdevelop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship replace) without charge.