Advertisement
Quick Links
Cordless Drills
-
Capacities
No load speed
Net weight
Steel
I
Wood
Wood screw
10
m m 1318")
600
Rimin.
1.1
kg (2.4 Ibs)
4.5 m m
x 2 0
mm
(311
6" x
314")
10 mm (318")
MODEL 6 0 1 0 D
10 mm (318") MODEL 6OlODW
10 mm (318")
MODEL 6OlODWK
With Fast Charger
With Fast Charger and Carrying Case
Overall length
227
m m
19")
INSTRUCTION MANUAL
Battery Cartridge 7000
Voltage
7.2 V
1
SPEC I FI CAT IO N
S
*
Model DC7100 Fast Charger
Dimensions
Net
Charging
IL
x
W
x
HI
weight
time
50 Hz
-
60 Hz
7.2 V
15-314"
x
3-118"
x 2-318")
( 1 5 lbs)
'
H r
Input
output
A.C
only
D.C.
145
m m
x
80 m m
x
61 mm
0.7 kg
Advertisement
Related Manuals for Makita 6OLODW
Summary of Contents for Makita 6OLODW
- Page 1 1318") (311 6" x Battery Cartridge 7000 Model DC7100 Fast Charger Voltage Input 7.2 V 50 Hz 10 mm (318") 10 mm (318") MODEL 6OlODW 10 mm (318") No load speed x 2 0 Rimin. 314") Dimensions output only D.C.
-
Page 2: Important Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. OUTDOOR USE EXTENSION CORDS.
- Page 4 Before using battery charger, read all instructions and cautionary markings battery charger, CAUTION - To reduce risk of injury, charge only MAKITA Battery Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger t o rain or snow.
-
Page 5: Additional Safety Rules
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. - Page 6 Installing or removing battery cartridge *Always switch off the tool before inser- tion or removal of the battery cartridge. * T o remove the battery cartridge, pull out plate on the bottom of the tool s e t and grasp both sides of the cartridge while withdrawing it from the barrel.
- Page 7 Bit installation & removal CAUTION : Always set the Forward-Reverse switch lever to NEUTRAL when installing, removing or adjusting bits or accessories. Chuck When installing drill bit, notice that there are three holes in the chuck which you must use the key for tighten- ing.
- Page 8 Switch action Move the reversing switch lever to the & position for clockwise rotation or position for counterclockwise. ) J & To start the tool, simply pull the trigger. Release the trigger to stop. When the re- versing switch lever is in the neutral posi- tion, the tool will not start even if you pull the trigger Drill...
- Page 9 *Pressing down too hard on the tool will not speed up the drilling. I n fact, this undue pressure will only serve to damage the tip of your drill bit, decrease your drilling per- formance and shorten the service *There i s tremendous force exerted on the tool/bit Grip the drill firmly and exert care when the bit begins to break through the materials.
- Page 10 Grip .The grip shown on the right is recom- mended. However, grip the tool firmly with both hands when drilling a large- diameter hole. *The hole on the heel the tool is venient way to carry it by a cord, hook or other means.
- Page 11 Holds with extra battery Part No. 823033-3C Rubber pad assembly Part No. 123001-2 Foam polishing pad Part No. 743023-2 with your Makita tool specified in this Fast charger Part Model D C 7 1 0 0 784214-0A Part No. 113086-6...
- Page 12 M a r ~ - l 1 - ' 8 7 US 10 mm (318") CORDLESS DRILL Model 6010D Note: The switch and other part configurations may differ from country to country.
- Page 13 MODEL 6010D DESCRIPTION $ : D Pan Head Screw M5x18 Drill Chuck S10 Gear Plane Bearing 5 DC Motor 7 2 V Plane Bearing Gear 1 3 - 5 8 Plane Bearing Switch Note The switch other part specifications may ,",",, DESCRIPTION Housing...
- Page 14 MAKITA LIMITED ONE YEAR WARRANTY I<very Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE Y l A R from the date of original purchase.