Tile Cutting Accessories - Husqvarna TS 250 X3 Operator's Manual

.15

TILE CUTTING ACCESSORIES

ANGLE GUIDE PROTRACTOR
542 05 10-20* 542 05 10-10*
Parts List:
Diag. Part No.
1 542 05 01-04*
2 542 05 01-07*
3 542 05 01-05*
4 542 05 01-06*
5 542 05 01-03*
6 542 18 97-37*
7 542 05 10-20*
8 542 18 97-37*
9 N/A
RIP FENCE: 542 05 10-00* - The Rip Fence is a standard
accessory supplied with every tile saw. It is used
to provide a repeatable position for rip cuts until
relocated. The Rip Guide clamps to the machined
backstop of the conveyor cart.
ADJUSTABLE PROTRACTOR: 542 05 10-10* - The
Protractor can be used to rip cut known angles. The
protractor clamps to the backstop.
DUAL 45 ANGLE GUIDE: 542 05 10-20* - This is a non-
adjustable miter used to quickly position the tile at
45 degrees; either on the left or right side. It is often
used for repeated diagonal rip cuts. The Angle Guide
clamps to the backstop.
BULLNOSE MITER GUIDE: 542 05 10-30* -This is a fixed
guide that positions the tile for a 45 degree miter cut.
The Mitering Guide clamps to the backstop.
The instructions for use and spare parts found in this document are for information only and are not binding. As part
of our product quality improvement policy, we reserve the right to make any and all technical modifications without
Qty. Description
1 Frame, Miter
1 Bar, Locking
1 Clip, Stop
1 Spring
1 Knob
2 Knob, 1/4"-20 x 1"
°
1 Miter Assy, 45
1 Knob, 1/4"-20 x 1"
1 Sector Plate
The manufacturer accepts no
responsibility caused by unsuitable
use or modifications.
MIGHTY MITER GUIDE
542 16 14-80*
Diag. Part No.
10 N/A
11 542 02 00-11*
12 542 02 02-44*
13 542 18 97-37*
14 542 05 10-10*
15 542 02 05-98*
16 542 05 10-30*
17 542 20 32-52*
18 542 05 01-02*
MIGHTY MITER GUIDE: 542 05 01-02* - This is a 45
degree fixture that has an adjustable clamp to hold
the tile while miter cutting. The Mitering Guide clamps
to the backstop.
FOLDING STAND: 542 20 32-52* - This stable stand
brings a Husqvarna® tile saw to standing level for
ease of work. The stand conveniently folds flat for
storage and transporting.
ADJUSTABLE ROLLING STAND: 542 20 32-53 - This
flexible-use stand can be adjusted from 29" to 33" in
height. It has standard rear wheels for easy transpor-
tation. When stand is collapsed, the front legs become
handles to wheel saw to and from jobsite. Springs
assist the raising and lowering of the saw. Addi tional
wheels are available to make rolling collapsed saw /
stand onto truck easier.
CART EXTENSION: 542 20 30-37 - Fastens to front edge
of 16-1/2" L x 16" W Conveyor Cart (542 20 30-83).
Adds 5-1/4" to length to help support larger tile.
prior notice.
BULLNOSE FOLDING STAND
542 05 10-30* 542 20 32-52*
Qty. Description
1 Arm, Protractor.
1 Carriage Bolt, 1/4"-20 x 5/8".
1 Wing Nut, 1/4"-20 x 1".
1 Knob, 1/4"-20 x 1".
1 Protractor Assy.
1 Screw, Thumb, 1/4"-20 x 1".
1 Holder Assy, Bullnose.
Stand, Tile Saw (for TS250X only).
1
1 Support Assy, Miter Frame