Using The Slip Mode; Slip Hot Cue - Pioneer XDJ-RX Operating Instructions Manual

Using Loop Slice
Loop Slice divides a loop into four sections, and plays the specified sec-
tion intervals repeatedly while the Performance button is pressed.
1 Switch to Loop Slice function by pressing the
[LOOP SLICE/EXIT] button.
2 Press the Performance button corresponding to the
beats to want be set (1 beat, 2 beats, 4 beats, 8 beats).
From the playback position where the Performance button was pressed,
the loops corresponding to the number of beats set are automati-
cally set, after which loop playback starts. During loop playback, the
Performance button will flash.
! If the track's BPM cannot be detected, the BPM is set to 120.
! This operation is not necessary when switching over to loop slice
function during loop playback.
3 Keep the Performance button pressed.
This plays the specified section intervals repeatedly.
To change the length of section interval without changing the
length of the loop, press the [CUE/LOOP CALL c (LOOP 1/2X)] or
[CUE/LOOP CALL d (LOOP 2X)] buttons while the Performance button
is pressed.
! Loop Slice does not work for loops longer than 16 seconds.
4 Release your finger from the Performance button.
! Loop playback continues if [LOOP SLICE] of the [UTILITY] screen is
[CONTINUE].
! If the [LOOP SLICE] of the [UTILITY] screen is [SINGLE], the player
plays the complete section interval and then instantaneously returns
to the set cue point and pauses playback.
 Canceling loop
Press the [LOOP SLICE/EXIT] button or the [RELOOP/EXIT]
button.
Cancels the loop and normal playback resumes.

Using the slip mode

When the slip mode is turned on, normal playback with the original
rhythm continues in the background while in the pause (vinyl mode),
scratch play, loop play, hot cue play and reverse play modes. When the
slip mode is canceled, normal playback resumes from the point reached
while the slip mode was turned on.
! When the quantize function is on, there may be a slight delay in
operation of this function in order to synchronize the beat.
(Only slip hot cue, Slip beat looping, Slip Loop Slice, and Slip
Reversing)
Display of the position playing in the background
! When in the slip mode, the currently playing position is indicated
by a yellow line on the main unit display's waveform display (overall
waveform or enlarged waveform). The position playing in the back-
ground is indicated by a white line on the main unit display's wave-
form display (overall waveform).
 Slip pausing
1 Press the [VINYL MODE] button.
Set the jog mode to VINYL.
2 Press the [SLIP] button.
The mode switches to the slip mode.
3 During playback, press the [f (PLAY/PAUSE)]
button.
Normal playback continues in the background even while in the pause
mode.
The [SLIP] button flashes in beat with the sound playing in the
background.
4 Press the [f (PLAY/PAUSE)] button to cancel pause
mode.
Normal playback of the sound that was playing in the background
resumes.
 Slip scratching
1 Press the [VINYL MODE] button.
Set the jog mode to VINYL.
2 Press the [SLIP] button.
The mode switches to the slip mode.
3 During playback, press the top of the jog dial.
The scratch play mode is set.
Normal playback continues in the background even while scratch-
ing. The [SLIP] button flashes with the beat of the sound playing in the
background.
4 Release your hand from the top of the jog dial.
Normal playback of the sound that was playing in the background
resumes.
 Slip looping
1 Press the [SLIP] button.
The mode switches to the slip mode.
2 Press the [LOOP IN/4BEAT (IN ADJUST)] button, then
press the [LOOP OUT (OUT ADJUST)] button.
Loop playback starts.
Normal playback continues in the background even during loop
playback.
The [SLIP] button flashes in beat with the sound playing in the
background.
! Loops of over 8 seconds cannot be set.
! The same operation is performed when the [LOOP IN/4BEAT
(IN ADJUST)] button is pressed for over 1 second and a loop is set.
3 Press the [RELOOP/EXIT] button.
Looping is canceled, and normal playback of the sound that was playing
in the background resumes.

 Slip hot cue

1 Press the [SLIP] button.
The mode switches to the slip mode.
2 Press the [HOT CUE/CALL] button to switch to the hot
cue mode.
3 Keep the Performance button pressed.
Hot cueing begins.
Normal playback of the sound playing in the background continues even
while the Performance button is keep pressed.
The [SLIP] button flashes in beat with the sound playing in the
background.
15
En