AEG CTV 4807 Instruction Manual page 31

Videotext
Depending on the channel which is set, additional information
can be displayed via videotext in TV mode.
Videotext with a satellite reception:
Videotext is only available when receiving via satellite if
the satellite receiver supports this function. Call the
videotext functions up via the satellite receiver.
Press the "TEXT" button.
The index page of the set station's videotext is displayed.
To call up a different text page, enter the number of this page
using the numerical buttons.
The desired page is displayed after a short while.
If you wish to stop selection of a new page, press the "HOLD"
button.
In the case of certain stations, the coloured buttons on
the remote control can be used to call up certain
functions. The function which is possible in each case is
then displayed on the bottom edge of the screen.
To switch to the next videotext page, press the "
button.
To switch to the previous videotext page, press the "PROG
" button.
To enlarge the character size, press the "SIZE" button.
The upper half of the current page is enlarged.
To display the lower half of the current page, press the "SIZE"
button again.
To return the page to normal size again, press the "SIZE"
button a third time.
If you would like to view the television picture and videotext at
the same time, press the "MIX" button.
To watch the television programme whilst a videotext page is
being loaded, proceed as follows:
Use the numerical buttons to select the desired page and
then press the "CANCEL" button.
The television programme is displayed. "TEXT" is displayed on
the screen. When the desired videotext page has been loaded,
"TEXT" is displayed in blue.
To display the videotext page which has been loaded, press
the "CANCEL" button again.
To switch the videotext off, press the "TEXT" button.
Within the videotext, certain stations additionally transmit
concealed pages or pages comprised of several sub-pages.
To display concealed pages, press the "REVEAL" button.
Timer
The timer function can be used to set the time after which the
television set is switched on ("ON TIMER") or at which the
television switches to a different station ("PROG TIMER").
To use the "ON TIMER" function, proceed as follows:
Press the "TV MENU" button and use the "
" buttons to select the "TIME" menu.
Use the "
TIMER" setting.
Use the "
time range.
A time range of 10, 30, 60 or 90 minutes can be selected.
Use the "
"@CHANNEL" setting below this.
Use the "
channel.
To integrate the settings and close the menu, press the "TV
MENU" button.
To automatically switch to another station at a pre-selected point
PROG"
in time, proceed as follows:
Press the "TV MENU" button and use the "
" buttons to select the "TIME" menu.
Use the "
"PROG TIMER" setting.
Use the "
time range.
A time range of 10, 30, 60 or 90 minutes can be selected.
Use the "
"@CHANNEL" setting below this.
Use the "
which the television set is to switch.
To integrate the settings and close the menu, press the "TV
MENU" button.
Sleep function
The sleep function can be used to set the time after which the
television set automatically switches to standby mode:
Press the "SLEEP" button repeatedly until the desired time
range is displayed on the screen.
The SLEEP function can also be activated via the "TV MENU":
Press the "TV MENU" button and use the "
" buttons to select the "TIME" menu.
Use the "
"SLEEP" setting.
Use the "
time range.
A time range of 10, 30, 60 or 90 minutes can be selected.
To integrate the settings and close the menu, press the "TV
MENU" button.
PROG" or "PROG " buttons to select the "ON
VOL" or "VOL " buttons to select the desired
PROG" or "PROG " buttons to switch to the
VOL" or "VOL " buttons to select the desired
PROG" or "PROG " buttons to select the
VOL" or "VOL " buttons to select the desired
PROG" or "PROG " buttons to switch to the
VOL" or "VOL " buttons to select the channel to
PROG" or "PROG " buttons to select the
VOL" or "VOL " buttons to select the desired
Operation
VOL" or "VOL
VOL" or "VOL
VOL" or "VOL
31