Related Manuals for Makita M363
Summary of Contents for Makita M363
- Page 1 INSTRUCTION MANUAL Router M363 004924 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
-
Page 2: Specifications
ENGLISH SPECIFICATIONS Model M363 Collet chuck capacity 12 mm or 1/2" Plunge capacity 0 - 60 mm No load speed (min 22,000 Overall height 300 mm Net weight 5.5 Kg Safety class • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. -
Page 3: Additional Safety Rules
rate for which it was designed. Avoid cutting nails. Inspect for and remove all 17. Do not use the power tool if the switch does nails from the workpiece before operation. not turn it on and off. Any power tool that cannot Hold the tool firmly with both hands. -
Page 4: Nylon Nut
Place the tool on a flat surface. Loosen the lock lever Switch action and lower the tool body until the bit just touches the flat 1. Switch lever surface. Press the lock lever down to lock the tool body. While pressing the fast-feed button, move the stopper pole up or down until the desired depth of cut is obtained. -
Page 5: Operation
1. Feed direction OPERATION 2. Bit revolving direction 1. Chip deflector 3. Workpiece 4. Straight guide 001985 005112 NOTE: When using the straight guide or the trimmer guide, • be sure to install it on the right side in the feed CAUTION: direction. - Page 6 1. More than 15 1. Bit 2. Base 2. Straight guide 3. Templet 3. Wood 4. Workpiece 5. Distance (X) 6. Outside 55 mm diameter of the templet guide 55 mm 7. Templet guide 004931 003695 When using a large diameter bit, attach pieces of wood NOTE: to the straight guide which have a thickness of more The workpiece will be cut a slightly different size...
-
Page 7: Maintenance
When operating the tool in the inverted position with the the vacuum head out of the tool base while holding the Makita Router Stand, use the spacer. supports between thumb and finger. The spacer prevents the router bit from dropping in to the chuck when replacing the bit. -
Page 8: Replacing Carbon Brushes
1. Brush holder 2. Screwdriver 005117 004942 1/2" To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be 1/4" performed by Makita Authorized Service Centers, 006453 always using Makita replacement parts. - Page 9 "V"Grooving bit 1/2" 3/8" 1/4" 006456 005118 Drill point double flush trimming bit 1/4" 006454 Dovetail bit 005121 1/2" 3/8" 005119 1/4" 006457 Slotting cutter 14.5 15SE 3/8" 14.5 14.5 15LE 3/8" 3/8" 006455 Drill point flush trimming bit 005122 1/2"...
- Page 10 Board-jointing bit Chamfering bit 005123 005126 1/2" 006461 005124 1/2" 005127 1/2" 006459 Corner rounding bit 30 E 1/4" 45 E 1/4" 60 E 1/4" 006462 Beading bit 005125 1/4" 1/2" 005128 1/4" 006460 1/2" 006463...
- Page 11 Cove beading bit Ball bearing chamfering bit 005129 005132 1/4" 1/4" 006464 45 E 1/4" Ball bearing flush trimming bit 60 E 1/4" 006467 Ball bearing beading bit 005130 005133 1/4" 006465 Ball bearing corner rounding bit 1/4" 1/4" 006468 Ball bearing cove beading bit 005131 005134...
- Page 12 1/4" 1/4" 006469 Ball bearing roman ogee bit 005135 1/4" 1/4" 006470 Double ball bearing round corner bit 005136 1/2" 006471...
- Page 16 Makita Corporation 884582-8...