Motorola NX-7510 Series Installation Manual
Motorola NX-7510 Series Installation Manual

Motorola NX-7510 Series Installation Manual

Integrated services platform ac or dc power supply module

Advertisement

NX-7510/NX-7520/NX-7530 Series
Integrated Services Platform
Installation Guide

Advertisement

Table of Contents
loading

Summary of Contents for Motorola NX-7510 Series

  • Page 1 NX-7510/NX-7520/NX-7530 Series Integrated Services Platform Installation Guide...
  • Page 2 NX-7510/NX-7520/NX-7530 Series Integrated Services Platform MOTOROLA SOLUTIONS and the Stylized M Logo are registered in the US Patent & Trademark Office. © Motorola Solutions, Inc. 2014. All rights reserved.
  • Page 3: Table Of Contents

    Installation Guide 1.0 Introduction ..............5 1.1 Document Conventions .
  • Page 4 5.0 Motorola Solutions Support Center ........
  • Page 5: Introduction

    Installation Guide Introduction The NX-7500 Series Integrated Services Platform lets you centrally administer networks of up to 2,048 WLAN Access Points geographically dispersed over small or medium sized enterprise locations. WiNG 5 Access Points intelligently handle the traffic flows, quality of service and security at remotely distributed locations, while the NX-7500 series integrated services platforms provide a single point for configuration, policy setting, and remote troubleshooting.
  • Page 6: Site Preparation

    NX-7510/NX-7520/NX-7530 Series Integrated Services Platform 1.3 Site Preparation • Consult your site survey and network analysis reports to determine specific equipment placement, power drops, and so on. • Assign installation responsibility to the appropriate personnel. • Identify and document where all installed components are located. •...
  • Page 7: Additional Recommended Equipment

    Ensure the electrical circuit through which the integrated services platform is CAUTION powered can safely accommodate a 300 Watt power supply. Motorola Solutions highly recommends you connect the NX-7500 series integrated CAUTION services platform to an Uninterruptible Power Supply (UPS). There are instances in...
  • Page 8: Safety Instructions For Rack Mount Installations

    • Rack Mount Rails - Use only industry-standard mounting kits when installing the NX-7500 series integrated services platform, as improper mounting may result in hardware failure and hazardous conditions. Motorola recommends using the mounting rails included with the integrated services platform.
  • Page 9: Power Supply Status Leds

    Installation Guide 1.8 Power Supply Status LEDs Each NX-7500 AC or DC power supply module has a single bi-color LED to indicate power supply status. The LED is visible on the rear panel of each installed power supply. The LED functionality for the power supplies is listed in the following table: State Description No power to all power supplies...
  • Page 10: Hardware Installation

    NX-7510/NX-7520/NX-7530 Series Integrated Services Platform Hardware Installation The following sections describe the hardware installation for the NX-7500 series integrated services platform. The following figure represents the front of the NX-7510 and NX-7520 models: The following figure represents the front of the NX-7530 model: To prepare for the installation: 1.
  • Page 11: Installing The Nx-7500 Series Services Platform

    6. Apply power to the integrated services platform. 7. When the prompt is displayed in the console window, login to the Command Line Interface (CLI) using username admin and password motorola. 8. When prompted, enter a new password, then enter it again to confirm it.
  • Page 12: Nx-7500 Series Power Supply Installation

    NX-7510/NX-7520/NX-7530 Series Integrated Services Platform 2.2 NX-7500 Series Integrated Services Platform Power Supply Installation Power down the the integrated services platform and disconnect all power cords prior WARNING! to installing or replacing a power supply. Ensure that the connectors at on the back of the power supply do not come into CAUTION contact with your hands or the packing material as you unpack the power supply.
  • Page 13: Nx-7500 Series Nmc Installation

    Installation Guide 2.3 NX-7500 Series Integrated Services Platform NMC Installation Power down the integrated services platform and disconnect all power cords prior to WARNING! installing or replacing the Network Mezzanine Card (NMC). The NMC module uses lasers. The lasers are compliant with the requirements for a CAUTION Class 1 laser product and are inherently eye safe in normal operation.
  • Page 14: Nx-7500 Series Sfp Installation

    NX-7510/NX-7520/NX-7530 Series Integrated Services Platform 9. Apply power to the integrated services platform. 10. Verify that the integrated services platform LCD panel is illuminated. 11. Login in to the Management Interface and verify that the replacement NMC is operational. 2.4 NX-7500 Series Integrated Services Platform SFP Installation The NX-7500 series integrated services platform supports use of SFP transceivers SPF transceivers are keyed so that they can only be installed with the correct NOTE...
  • Page 15: Nx-7530 Disc Drive Assembly Replacement

    Installation Guide 2.5 NX-7530 Integrated Services Platform Disc Drive Assembly Replacement Power down the integrated services platform and disconnect all power cords prior to WARNING! installing or replacing the disc drive. The NX-7530 integrated services platform configuration includes a hard drive disc assembly and Redundant Array of Independent Disks (RAID).
  • Page 16: Specifications

    NX-7510/NX-7520/NX-7530 Series Integrated Services Platform Specifications 3.1 Physical Specifications Dimensions 1U, rack mountable 17.2 in W x 1.76 in. H x 21.28 in. D 430 mm W x 42 mm H x 532 mm D Weight NX-7510 –19 lb./8.62 kg (with 1 power supply) NX-7520 –...
  • Page 17: Regulatory Information

    This device is approved under the Motorola Solutions, Inc. brand (“Motorola”) This guide applies to the following Model Numbers: NX-7510, NX-7520, NX-7530 devices. All Motorola Solutions devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required.
  • Page 18: Statement Of Compliance

    NX-7510/NX-7520/NX-7530 Series Integrated Services Platform 4.4 Statement of Compliance Motorola Solutions hereby declares that this device is in compliance with all the applicable Directives, 2004/108/EC, 2006/95/EC, and 2011/65/EU. A Declaration of Conformity may be obtained from http://www.motorolasolutions.com/doc. Japan Voluntary Control Council for Interference (VCCI) Class A ITE...
  • Page 19: Waste Electrical And Electronic Equipment (Weee)

    Installation Guide 4.5 Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Motorola Solutions for recycling. For information on how to return product, please go to: http://www.motorolasolutions.com/recycling/weee.
  • Page 20: Turkish Weee Statement Of Compliance

    NX-7510/NX-7520/NX-7530 Series Integrated Services Platform Dansk: Til kunder i EU: Alle produkter skal returneres til Motorola Solutions til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: http://www.motorolasolutions.com/recycling/weee. Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρέφονται...
  • Page 21 • Model number or product name • Software type and version number Motorola Solutions responds to calls by e-mail, telephone, or fax within the time limits set forth in support agreements. If you purchased your product from a Motorola Solutions business partner, contact that business partner for support.
  • Page 22 NX-7510/NX-7520/NX-7530 Series Integrated Services Platform NX-7500 Series China RoHS Compliance (Pb) (Hg) (Cd) (PBDE) (PBB) (Parts) (Metal Parts) (Circuit Modules) (Cables and Cable Assemblies) (Plastic and Polymeric Parts) (Optics and Optical Components) (Batteries) SJ/T11363-2006 SJ/T11363-2006 This table was created to comply with China RoHS requirements.
  • Page 23 Installation Guide...
  • Page 24 Schaumburg, IL 60196-1078, U.S.A. http://www.motorolasolutions.com MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2014 Motorola Solutions, Inc. All Rights Reserved.

This manual is also suitable for:

Nx-7530 seriesNx-7520 series

Table of Contents