Page 1
Hybrid IP-PBX Getting Started KX-TDA100 KX-TDA200 Model Thank you for purchasing a Panasonic Hybrid IP-PBX. Please read this manual carefully before using this product and save this manual for future use. KX-TDA100/KX-TDA200: PMPR Software File Version 3.0000 or later...
Table of Contents Before Installation .................. 3 System Connection Diagram ...................4 Unpacking..........................5 Installation....................7 Opening/Closing the Front Cover..................8 Inserting the SD Memory Card to the MPR Card............9 Installing the Option Units ....................9 Installing the Trunk Cards ....................11 Installing the Extension Cards (DLC8/DLC16/DHLC8/MSLC16/SLC8/SLC16)... 14 Connecting Extensions ....................14 Frame Earth Connection ....................15 Starting the Hybrid IP-PBX ..............
Check the package contents. Main Unit × 1 CD-ROM (including manuals, etc.) × 1 AC Cord* × 1 Screw A Screw B (Black) × 3 (KX-TDA100) × 2 (KX-TDA100) × 4 (KX-TDA200) × 6 (KX-TDA200) Anchor Plug Mini Plug (for pager and SD Memory Card ×...
Page 6
1.2 Unpacking Necessary tools (not supplied): Telephone cable for extension connection: Diameter of cable Maximum length of cable (ø 0.4 mm to ø 0.6 mm) ø 0.5 mm 1128 m for SLT ø 0.5 mm 720 m for KX-T7600 series ø...
2.1 Opening/Closing the Front Cover Opening/Closing the Front Cover Opening the Front Cover Insert a flathead screwdriver into the opening (on the left of the screw cover) and unlatch the screw cover. Turn the screw anticlockwise to loosen. Slide the front cover to the right until it stops, then lift the front cover. Closing the Front Cover Hook the front cover onto the shelf (line up the protrusions on the cover with the receptacles on the shelf), then slide the front cover to the left until it locks.
Hybrid IP-PBX to fail to start when you try to restart the system. Installing the Option Units Slot Condition Install the power supply unit (PSU) into the left-most slot, and optional service cards into free slots. KX-TDA100 KX-TDA200 Null Slot* PSU Slot...
Page 10
2.3 Installing the Option Units CAUTION To protect the back board from static electricity, do not touch parts on the back board in the main unit, PSU, and on the optional service cards. To discharge static electricity, touch ground or wear an earthing strap.
2.4 Installing the Trunk Cards Be sure to cover each slot in which no optional service card is installed by using a Blank Slot Cover. For details, refer to "Covering the Blank Slots" in "2.2.7 Installing/Removing the Optional Service Cards" of the Installation Manual. Installing the Trunk Cards LCOT4/LCOT8/LCOT16 Card Example: LCOT16 Card...
Page 12
2.4 Installing the Trunk Cards BRI4/BRI8 Card Example: BRI8 Card To attach the ferrite core When using 1 or 2 cables: RJ45 TX2(-) RX1(-) RX2(+) TX1(+) LINE 1 to LINE 8 When using 3 or 4 cables: To NT1 • For every 4 cables, use 1 ferrite core;...
Page 13
2.4 Installing the Trunk Cards PRI30/PRI23 Card Example: PRI30 Card To attach the ferrite core RJ45 5 cm BNC (TX) To NT1 BNC (RX) To NT1 For RJ45 120Ω 120Ω 75Ω 75Ω For BNC Accessories (included): Ferrite core × 1 User-supplied (not included): RJ45 or BNC connectors Notes •...
2.5 Installing the Extension Cards (DLC8/DLC16/DHLC8/MSLC16/SLC8/SLC16) Installing the Extension Cards (DLC8/DLC16/ DHLC8/MSLC16/SLC8/SLC16) Example: DHLC8 Card To attach the ferrite core 3 cm Amphenol To extensions Accessories (included): Screws × 2, Ferrite core × 1 User-supplied (not included): Amphenol connector Note Attach the included ferrite core to the cable.
2.7 Frame Earth Connection Frame Earth Connection IMPORTANT Connect the frame of the Hybrid IP-PBX to earth. Loosen the screw. Screw Insert an earthing wire (user-supplied)*. Tighten the screw. Connect the earthing wire to earth. Earthing wire To earth * For earthing wire, green-and-yellow insulation is required, and the cross-sectional area of the conductor must be more than 0.75 mm or 18 AWG.
3.1 Starting the Hybrid IP-PBX Starting the Hybrid IP-PBX CAUTION • SD Memory Card must be inserted in the SD Memory Card slot of the MPR card before start • Before touching the System Initialise Switch, discharge static electricity by touching ground or wearing an earthing strap.
4.1 Connecting the PC Connecting the PC KX-TDA Maintenance Console serves as an overall system programming tool for the Hybrid IP-PBX. KX-TDA Maintenance Console's Quick Setup lets you easily configure the Hybrid IP-PBX to receive intercom and trunk calls, as well as apply basic settings such as time and date. Note The contents and design of the software are subject to change without notice.
4.3 Programming the Hybrid IP-PBX Programming the Hybrid IP-PBX Starting the KX-TDA Maintenance Console and Assigning the Basic Items (Quick Setup) When you start the KX-TDA Maintenance Console with the Installer Level Programmer Code and connect to the Hybrid IP-PBX for the first time after initialisation (with the factory default setting), Quick Setup will launch automatically.
Page 22
4.3 Programming the Hybrid IP-PBX When country/area data do not match: Click [OK] to replace the country/area data of the Hybrid IP-PBX. Replacement may take several minutes to complete. Follow the procedure described in "Starting the Hybrid IP-PBX" and restart the Hybrid IP-PBX. Repeat steps 5 to 6 to restart the KX-TDA Maintenance Console.
Page 23
4.3 Programming the Hybrid IP-PBX Click "Tool" → "BRI Automatic Configuration" from the menu bar. Click "Check" to turn on the BRI card. Click [OK]. Enter the Subscriber Number for the desired ports. Click [Execute]. ISDN line data such as P-P/P-MP, TEI Mode are automatically set.
Page 24
4.3 Programming the Hybrid IP-PBX For ISDN trunk user (DDI Setting): Double-click "CO & Incoming Call". Double-click "DDI/DID Table". For necessary items, enter the proper numbers and selections. Click [OK]. For ISDN trunk user (MSN Setting): Double-click "CO & Incoming Call". Double-click "DIL Table &...
Page 25
4.3 Programming the Hybrid IP-PBX Double-click "Extension". Double-click "DSS Console". Double-click "Main". Enter the Pair Extension Number. 10. Click [OK]. 11. Double-click "Flexible Key". 12. For necessary items, enter the proper numbers and selections. 13. Click [OK]. 14. Double-click "Configuration". 15.
Page 26
4.3 Programming the Hybrid IP-PBX Getting Started...
5.1 Making Calls Making Calls To call another extension extension no. Dial extension number. Talk. Off-hook. To call an outside party outside phone no. Off-hook. Talk. Enter automatic Dial outside phone line access number. number. Getting Started...
Page 30
Panasonic Communications Co., Ltd./Panasonic Communications Company (U.K.) Ltd. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. Declarations of Conformity for the relevant Panasonic products described in this manual are available for download by visiting: http://www.doc.panasonic.de...