Precautions On Adjusting - Sony DCR-TRV30E Service Manual

3-1-2.

Precautions on Adjusting

1) The adjustments of this unit are performed in the VTR mode
or camera mode.
To set to the VTR mode, set the power switch to "VCR" or set
the "Forced VTR Power ON mode" using the adjustment remote
commander (Note 1).
To set to the Camera mode, set the power switch to "CAMERA"
or set the "Forced Camera Power ON mode" using the
adjustment remote commander (Note 2).
After completing adjustments, be sure to exit the "Forced VTR
Power ON Mode" or "Forced Camera Power ON Mode".
(Note 3)
2) The front panel block (MI-043 board (Microphone amp., remote
commander receiver, LASER LINK), ML-023 board (MIC
jack, LANC jack) SE-121 board (MF sensor, photo transistor))
must be assembled for connecting the adjustment remote
commander.
To remove it, disconnect the following connector.
MI-043 board CN2003 (37P, 0.5mm)
3) The viewfinder (LB-072 board) is need not be connected. To
remove it, disconnect the following connector.
CK-102 board CN1801 (20P, 0.5mm)
4) Cabinet (R) (CK-102 board, LCD block) need not be connected.
But removing the cabinet (R) (removing the VC-264 board
CN003) means removing the lithium 3V power supply (CK-
102 board, BT3201) , data such as date, time, user-set menus
will be lost. After completing adjustments, reset these data. If
the cabinet (R) has been removed, the self-diagnosis data, data
on history of use (total drum rotation time etc.) will be lost.
Before removing, note down the data of page: 2, address: A2
to AA (data on history of use) and the data of page: 2, address:
B0 to C6 (self-diagnosis data). (Refer to "5-4.Service Mode"
for the data on the history use and the self-diagnosis data.)
To remove the cabinet (R), disconnect the following connectors.
VC-264 board CN003 (70P, 0.5mm)
5) The lens block (CD-320 board) is need not be connected. To
remove it, disconnect the following connector.
VC-264 board CN301 (50P, 0.5mm)
6) The memory stick connector is need not be connected. To
remove it, disconnect the following connector.
VC-264 board CN011 (9P, 0.5mm)
7) By setting the "Forced VTR Power ON mode" or "Forced
Camera Power ON mode", the video section can be operate
even if the control switch block (FK-1800) has been removed.
When removing it, disconnect the following connector.
VC-264 board CN008 (45P, 0.3mm)
8) The flash unit is need not be connected. To remove it, disconnect
the following connector.
VC-264 board CN0012 (23P, 0.3mm)
Note 1: Setting the "Forced VTR Power ON" mode (VTR mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the VTR power to be turned on
with the control switch block (FK-1800 block) removed.
After completing adjustments, be sure to exit the "Forced Power
ON mode".
Note 2: Setting the "Forced Camera Power ON" mode (Camera mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the camera power to be turned
on with the control switch block (FK-1800 block) removed.
After completing adjustments, be sure to exit the "Forced Power
ON mode".
Note 3: Setting the "Forced Memory Power ON" mode (Memory mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 05, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the memory power to be turned
on with the control switch block (FK-1800 block) removed.
After completing adjustments, be sure to exit the "Forced Power
ON mode".
Note 4: Exiting the "Forced Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 0, address: 01, and set data: 00.
5-41