Page 1
Operating Instructions (For Basic Operations) Electronic Board (elite Panaboard) UB-T780BP Model No. UB-T780BP Stand is sold separately. Installation Manual Included (for qualified service personnel) • To assemble this unit, please refer to the Installation Manual on pages 29 through 48.
Introduction Introduction Thank you for purchasing the Panasonic Electronic Board. For optimum performance and safety, please read these instructions carefully. Feature Highlights The elite Panaboard is supplied power through the USB cable connected to a computer. You do not need to plug in the elite Panaboard to an AC outlet.
Page 3
Introduction Things you should keep a record of Attach your sales receipt here For your future reference Date of purchase Serial number Dealer’s name Dealer’s address Dealer’s tel no. About the Operating Instructions There are 2 separate operating manuals for the elite Panaboard. For Basic Operations Instructions for connecting and operating the elite Panaboard, as (this document)
Page 4
Introduction • All other trademarks identified herein are the property of their respective owners. Federal Communications Commission Requirements For United States Only Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
For details about the system requirements, refer to the Operating Instructions (For Software). Exemption of Liability Panasonic System Networks Co., Ltd. is not responsible for accidents or injuries caused by, but not limited to, the following: Altering the device or improper installation construction.
Table of Contents Table of Contents For Your Safety ..................7 For Your Safety .........................7 Precautions ........................10 Usage ......................11 Included Accessories .....................11 Names and Uses of the Parts ..................12 Connecting External Components ................15 Installing the elite Panaboard software ................17 Setting the Projector .......................18 Setting Your System (Calibration) .................19 Starting the elite Panaboard software and Performing Calibration ......20 Uninstalling the elite Panaboard software ..............21...
For Your Safety For Your Safety For Users For Your Safety To prevent severe injury and loss of life, read this WARNING section carefully before using the unit to ensure proper and safe operation of your unit. The following graphic symbols are used in this Power Operating Instructions manual.
Page 8
For Your Safety Installation and Relocation Make sure that the battery is installed with the correct polarity as indicated on Have the unit installed, removed and the battery holder. Incorrectly installed disposed of only by qualified service batteries may burst or leak, resulting in personnel.
Page 9
For Your Safety When moving the unit, be sure to CAUTION disconnect the USB cable from the computer. If the unit is moved with the UBS cable attached, it can cause damage to the cable which could result Power in fire or electric shock. When the unit is not used over an Move this unit with two persons.
For Your Safety Operating Safeguards Precautions If the unit is fallen down or damaged, About Using the Battery disconnect the USB cable. Otherwise, it If a battery is used improperly, the battery may leak, may cause fire or electric shock. causing corrosion of the unit, or it may burst.
Usage Usage Included Accessories Check that all of the following items are included with your elite Panaboard. In the event that an item is missing, please contact your dealer. List of Accessories USB Cable AAA Battery (LR03) Software CD-ROM (5 m [16 ft. 4 in.]) (Disposable) Operating Instructions...
Usage Names and Uses of the Parts Screen Front View Position Sensor Detects the position of the electronic pen. Do not block the sensor while operating the elite Panaboard. Screen Board Project the contents of a computer screen using a projector.
Page 13
Usage Electronic Pen Penpoint When you push down on the penpoint, ultrasonic waves and infrared signals are transmitted, and equivalent of a left mouse click is performed. Ultrasonic Emitter Do not block this area with your fingers. Doing so will prevent the elite Panaboard from correctly detecting the electronic pen's position.
Page 14
Usage Inserting (Replacing) Batteries 1. Remove (replace) the battery cover. 2. Insert (exchange) the battery and replace the cover. • When replacing the cover, follow the procedure in • Make sure to use a AAA alkaline battery, and reverse. ensure that face the correct directions.
Usage Connecting External Components Connect the elite Panaboard to a computer using the USB cable (included). • Be sure the elite Panaboard software is installed on the computer before connecting it to the elite Panaboard. • elite Panaboard: Plug the B connector (smaller connector) into the elite Panaboard's USB port. Computer: Plug the A connector (larger connector) into a USB port on the computer.
Page 16
Usage Moving the elite Panaboard When Using the Stand (Sold Separately) Disconnect the USB cable from the elite Panaboard. Release the locks on the casters. Move the elite Panaboard, avoid banging or shaking the board. Notice • Always move the elite Panaboard with 2 people. •...
When installation has finished, click [Finish]. • Restart your computer if you are prompted to do • The group [elite Panaboard] will be created in the [Panasonic] group in the program menu. • The following items will appear in the [elite Panaboard] group: –...
Usage Project the Image as a Rectangle Setting the Projector • Adjust the location of the projector to project at a Set up your projector as instructed below. right angle with the elite Panaboard. About Positioning the Image • When you are projecting an image, make sure that the edge of the projected image is at least 5 mm in.) from the screen frame.
Usage Setting Your System • If the image is projected trapezoidally, the position of the electronic pen may not be read (Calibration) correctly. Adjust the projector so that the projected image is a rectangle. Refer to your projector's documentation for information on About Calibration adjusting the projected image.
Usage Starting the elite Panaboard software and Performing Calibration Connect the elite Panaboard to your computer with the USB cable. • The elite Panaboard software starts • automatically. Hold and press the electronic pen at a right • angle to the screen board. When you start the elite Panaboard software for •...
Control Panel. • In Windows 2000, select [Add/Remove Programs], and in Windows Vista or Windows 7, select [Uninstall a program]. Select Panasonic elite Panaboard, then remove Follow the on-screen instructions. When uninstallation is complete, restart your computer. [Desktop Drawing Tool] •...
"Operating Instructions (For Software)". Turn on your computer and start Windows. Open "Operating Instructions (For Software)" from the Start menu. ([Start] ® [All Programs] ® [Panasonic] ® [elite Panaboard] ® [Operating Instructions for Software]) • The electronic documentation will be displayed.
Appendix Appendix Daily Care When cleaning the elite Panaboard or inside the elite Panaboard, make sure to disconnect the USB cable. Cleaning the elite Panaboard Replacing the Battery in the Electronic Pen When the charge in the battery in the electronic pen is low, the message, "The pen battery is low.
Appendix Replacing the Penpoint of the Electronic Pen As the penpoint of the electronic pen becomes worn, a hole will appear in the penpoint. Continuing to use the electronic pen in this condition can cause damage to the screen or unsatisfactory operation, so replace the penpoint with a new one as soon as possible.
Appendix Troubleshooting When experiencing problems, please refer to the table below for possible solutions. If the problem persists, contact your dealer. Symptom Possible cause and solution page The LEDs do not light Check that the USB cable is properly connected. when the USB cable is →...
Page 26
Appendix Symptom Possible cause and solution page Apart from writing directly on the elite Panaboard with the electronic pen, you pushed the penpoint with your finger while Extra lines are displayed – holding it close to the elite Panaboard. on the computer screen. →...
Before constructing or installing the elite Panaboard, please read "Installation Manual (for qualified service personnel)" carefully. Especially, please read "For Your Safety" carefully and install the elite Panaboard safely. Panasonic System Networks Co., Ltd. cannot be held responsible for accidents or damage to property resulting from incorrect installation. •...
Page 30
Installation Manual Have the unit installed, removed and CAUTION disposed of only by qualified service personnel. After installing or moving the electronic board, lock the casters and set the fall-prevention extension legs. Locking the casters (Push this side) Push to lock If the unit is hung on a wall, confirm the wall must be capable of supporting at least the following weight.
Installation Manual Included Accessories Confirm that the following items are included with the elite Panaboard. Part Name Illustration Q’ty Remarks USB Cable For computer (5 m [16 ft. 4 in.]) connection Operating Instructions (For Software) CD-ROM Drivers Application software Wall Mounting Plate (Left) —...
Installation Manual Wall Mounting Construction Checking the Wall When mounting on a wall, consult with your building's owner, caretaker or construction manager to determine if the wall strength is sufficient to install the elite Panaboard. For safety, install the elite Panaboard only after thoroughly understanding the type of walls, the appropriate types of screws and the construction method (Page 34).
Installation Manual Installing the Wall Mounting Plates Ensure that the wall is strong enough to support the elite Panaboard. Rated strength: greater than 1,324 N (135 kgf) Using the measuring tape and level, mark the 8 locations to insert the screws. 469.5 mm 813 mm 222.5 mm (8...
Installation Manual • Tighten the bolt so that it will not become loose. • When drilling the holes and installing the wall mounting plates, follow the procedure in "Wall Types and Installation Procedures" (page 34). Mount the elite Panaboard on the wall. See "Assembling the elite Panaboard"...
Page 35
Installation Manual Plasterboard walls Split-wing toggles (not included) are needed. Insert the bolt through the hole in the wall Split-wing toggle mounting plate and into the hole in the wall Plasterboard so that the arms of the split-wing toggle are horizontal.
Installation Manual Stand Assembly (Sold Separately) Included Parts Check that the following parts are included with the stand (KX-B061). Part Name Illustration Q'ty Stand Base Support Beam Cross Bar (A) Cross Bar (B) Screw (M6 ´ 45 mm [1 in.]) Two-wing Bolt (M5 ´...
Installation Manual CAUTION Before assembly, be sure to lock the casters. Locking the casters (Push this side) Assembly Instructions Assemble the fall-prevention extension legs. Operating Instructions (For Basic Operations)
Page 38
Installation Manual Assemble the stand. Assemble with the holes toward the front. REAR Locking caster side (rear) Locking caster side (rear) FRONT Notice • Do not over-tighten the screw ( ). (Doing so can warp the support beams.) • Assemble the stand so that the locking casters are on the rear side. Operating Instructions (For Basic Operations)
Page 39
Installation Manual Pull the fall-prevention extension legs down. Note • When folding back the fall-prevention extension legs, release the lock as follows ( Mount the elite Panaboard. See "Assembling the elite Panaboard" (For Mounting on a Stand (Sold Separately) ® page 46). Operating Instructions (For Basic Operations)
Installation Manual Assembly Instructions Preparing for Removing the elite Panaboard from Its Packaging Open the box, remove the accessory box & packing foam and open the plastic sheet of the elite Panaboard. Shipping Box Accessory Box Contents ] ....•...
Installation Manual For Wall Mounting (with 2-part lower Assembling the elite Panaboard frame cover) Note Remove the screw (A) of the attachment cover • There are 2 types of lower frame covers for the (B), which is fixed to the attachment board, and elite Panaboard: a lower frame cover made slide the attachment cover down.
Page 42
Installation Manual Unscrew the 4 screws from the front lower Fasten to the wall. frame cover. Fasten the lower portion of the board attachment securely to the wall. Lift the bottom of the front lower frame cover to remove it. Attach the front lower frame cover.
Page 43
Installation Manual For Wall Mounting (with 1-part lower Wipe the screen board surface. Gently wipe the screen board surface with a soft, frame cover) moist cloth. Remove the screw (A) of the attachment cover (B), which is fixed to the attachment board, and slide the attachment cover down.
Page 44
Installation Manual How to Attach the Lower Frame Cover Remove the lower frame cover. Remove the left and right screws, and then remove Holding the lower frame cover with both the lower frame cover from the main unit of the elite hands, slide it into the guides on both sides.
Page 45
Installation Manual Pull the lower frame cover ( Wipe the screen board surface. Gently wipe the screen board surface with a soft, While keeping the rear section of the lower moist cloth. frame cover against the rear of the board, push the lower frame cover up into the rear of the board ( Push the lower frame cover backward (...
Page 46
Installation Manual For Mounting on a Stand (Sold Note Separately) • When installing the elite Panaboard on the Hang the elite Panaboard on the stand with the stand, you can adjust its height to 4 different screw heads. levels. When changing the height, remove the left and right screws from the back of the elite Panaboard, and securely insert them at the desired height.
Installation Manual Confirming the elite Panaboard Operation After assembling the elite Panaboard, confirm that it operates properly by following the procedure below. Checkpoints Action Operation Measure 1 Connect to a computer Green LED lights. (Normal operation) using a USB cable. Green LED does not light, or Check the USB cable.
Installation Manual Repackaging To repackage the elite Panaboard, perform steps in the following "Assembling the elite Panaboard" in reverse. For Wall Mounting (with 2-part lower frame cover) ® page 41 • • For Wall Mounting (with 1-part lower frame cover) ® page 43 •...