Table of Contents
Advertisement
ENGLISH
x
The charger automatically shuts off if the ambient
temperature becomes too high. As a consequence
the charger will be inoperable. The charging base
must be disconnected from the mains supply and
$
taken to an authorised service centre for repair.
The charging base is intended for indoor use only.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Bowl release button
3. Charging indicator
4. Charging socket (DV4800N, DV9610PN and
WD9610ECN Only)
5. Dust bowl
6. Charger
7. Charging base (WD4810N, WD7210N and WD9610N
Only)
Fig. A
8. Dry pick up cloth filter (DV4800N, DV9610PN Only)
9. Pre-filter (DV9610N Only)
10. Wet/Dry foam insert (WD4810N, WD7210N, WD9610ECN
and WD9610N Only)
11. Wet/Dry deflector (WD4810N, WD7210N, WD9610ECN
and WD9610N Only)
Fig. B
12. Squeegee (WD4810N, WD7210N, WD9610ECN and
WD9610N Only)
13. Powered brush head (DV9610PN Only)
Installation
Wall Mounting (fig. C) (DV9610PN and WD9610ECN
Only)
The product can be attached to a wall to provide a convenient
storage and charging point for the appliance.
When fixing to a wall, make sure that the fixing method is
suitable for the wall type and is appropriate to the weight of
the appliance.
Mark the location of the screw holes (within reach of an
u
electrical outlet for chargeing the vac while it is on the wall
bracket).
Insert the charger cord into the curved slot in the wall
u
mount bracket leaving approximately 8-9 inches excess.
Hang the appliance on the wall by placing the opening
u
on the base of the vac over the hooks in the wall mount
bracket.
6
(Original instructions)
Assembly
Accessories (fig .B)
These models may be supplied with some of the following
accessories:
A squeege tool (12) for wet use on hard surfaces.
u
(WD4810N, WD7210N, WD9610ECN and WD9610N
Only)
A powered brush head (13) for vacuuming on cut pile
u
carpeting. The brush head is particularly useful for picking
up hair, threads, etc. (DV9610PN Only)
Fitting (Fig. D)
Insert the appropriate accessory into the front of the appli-
u
ance. Make sure that the accessory is pushed fully in.
Use
Before first use, the battery must be charged for at least
u
24 hours.
Place the appliance on the charging base whenever it is
u
not in use. (WD4810N, WD7210N and WD9610N Only)
Warning! Before charging, be sure to empty all liquid contents
and dry thoroughly, to avoid damage to your appliance.
Charging the battery (Fig. E & F)
Make sure that the appliance is switched off. The battery
u
will not be charged with the on/off switch in the on posi-
tion.
Plug the jack plug of the charger (6) into the charg-
u
ing socket (4) of the appliance (Fig. E). (DV4800N,
WD9610ECN and DV9610PN Only)
Place the appliance on the charging base (7) (Fig. F).
u
(WD4810N, WD7210N and WD9610N Only)
Plug in the charger. Switch on at the mains. The charging
u
indicator (3) will be lit.
Leave the appliance to charge for at least 16 hours.
u
While charging, the charger may become warm. This is
normal and does not indicate a problem. The appliance can
be left connected to the charger indefinitely. The charging
indicator (3) will be lit as long as the appliance is connected to
the plugged-in charger.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C.
Switching on and off (fig. G)
To switch the appliance on, slide the on/off switch (1)
u
forward to position 1.
To switch the appliance off, slide the on/off switch (1) back
u
to position 0.
Advertisement
Table of Contents
