Related Manuals for Horizon Fitness Adventure E
Summary of Contents for Horizon Fitness Adventure E
- Page 1 Adventure TREADMILL OWNER’S MANUAL Read the TREADMILL gUIDE before using this OWNER’S MANUAL.
- Page 3 ASSEMBLY WARNING There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises.
- Page 4 TOUCH PAD PANEL AND DISPLAY WINDOWS WATER BOTTLE HOLDER SAFETY KEY PLACEMENT GRIP PULSE HANDRAILS SUPPORT BAR ON/OFF SWITCH CONSOLE MAST FOOT LOCK LATCH (UNDERNEATH DECK) CIRCUIT BREAKER MOTOR COVER POWER CORD SIDE RAIL TRANSPORT WHEEL ROLLER END CAP REAR ROLLER RUNNING BELT / RUNNING DECK ADJUSTMENT BOLTS...
-
Page 5: Tools Included
PRE ASSEMBLY TooLS INCLUDED: 6 mm T-Wrench UNPACKING 5 mm L-Wrench 4 mm T-Wrench Place the treadmill carton on a level flat surface. It is recommended that you place 4 mm L-Wrench a protective covering on your floor. Take CAUTION when handling and transporting this unit. -
Page 6: Assembly Step
ASSEMBLY STEP 1 HARDWARE FoR STEP 1 PART TYPE DESCRIPTIoN SOCKET BOLT M6X1.0PX10L Open HARDWARE bAG 1. Cut the yellow banding and get console mast Attach the LEFT SoCKET (1) to the LEFT CoNSoLE MAST (2) using 4 SoCKET boLTS (A). - Page 7 ASSEMBLY STEP 2 HARDWARE FoR STEP 2 PART TYPE DESCRIPTIoN BOLT M8X1.25PX20L SPRINg WASHER Φ8.2xΦ15.4x2.0T FLAT WASHER Φ8.4xΦ15.5x1.6T Lift the RUNNING DECK upward until the FooT LATCH locks. Remove all contents from underneath the running deck. Open HARDWARE bAG 2. With the RUNNING DECK in the raised position, attach the LEFT CoNSoLE...
- Page 8 ASSEMBLY STEP 3 HARDWARE FoR STEP 3 PART TYPE DESCRIPTIoN BOLT M8X1.25PX20L SPRINg WASHER Φ8.2xΦ15.4x2.0T FLAT WASHER Φ8.4xΦ15.5x1.6T Open HARDWARE bAG 3. Pull LEAD WIRE (8) through RIGHT CoNSoLE MAST (4). After pulling the lead wire through the mast, the top of the CoNSoLE CAbLE (9) should be located at the top of the mast.
- Page 9 ASSEMBLY STEP 4 HARDWARE FoR STEP 4 PART TYPE DESCRIPTIoN SPRINg WASHER Φ8.2xΦ15.4x2.0T FLAT WASHER Φ8.4xΦ15.5x1.6T BOLT M8X1.25PX15L Disengage the DECK LoCK LATCH with your foot to lower the RUNNING DECK. Open HARDWARE bAG 4. gently place the CoNSoLE (10) on top of the CoNSoLE MASTS.
- Page 10 ASSEMBLY STEP 5 HARDWARE FoR STEP 5 PART TYPE DESCRIPTIoN BOLT M6X1.0PX15L Open HARDWARE bAG 5. Align SUPPoRT bAR (11) with holes in CoNSoLE MASTS. Insert boLTS (F) into all 4 holes of the SUPPoRT bAR (11). NOTE: Look into holes in the right mast before inserting bolts to avoid pinching cables.
- Page 11 ASSEMBLY STEP 6 Adventure E Overall Dimension : 1800 x 860 x 1360 mm / 71” x 34” x 53.5” Folding Dimension : 1210 x 860 x 1510 mm / 48” x 34” x 59.5” Max. User Weight: 125 kg / 275 lbs Net Weigh: 86 kg / 189.5 lbs...
-
Page 13: Treadmill Operation
TREADMILL OPERATION This section explains how to use your treadmill’s console and programming. The BASIC OPERATION section in the TREADMILL gUIDE has instructions for the following: • LoCATIoN oF THE TREADMILL • USING THE SAFETY KEY • FoLDING THE TREADMILL •... - Page 14 TIME DISTANCE TARGETS ZEIT ENTFERNUNG ZIELE TIME ZEIT DISTANCE ENTFERNUNG CALORIES INCLINE SPEED KALORIEN ENERGY SAVER STEIGUNG GESCHWINDIGKEIT ENERGIESPARMODUS CALORIES KALORIEN HEART RATE HERZFREQUENZ INCLINE SPEED STEIGUNG GESCHWINDIGKEIT km/h km/h km/h km/h km/h km/h INCLINE SPEED STEIGUNG GESCHWINDIGKEIT S T A R T S T O P ENTER COOL...
- Page 15 ADVENTURE E CoNSoLE oPERATIoN Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use. A) * LED DISPLAY WINDoWS: time, distance, calories, heart rate, speed, incline and workout profiles.
-
Page 16: Display Windows
TIME DISTANCE ZEIT ENTFERNUNG TARGETS ZIELE TIME ZEIT DISTANCE ENTFERNUNG CALORIES INCLINE SPEED KALORIEN ENERGY SAVER ENERGIESPARMODUS STEIGUNG GESCHWINDIGKEIT CALORIES KALORIEN HEART RATE HERZFREQUENZ DISPLAY WINDoWS • TIME: Shown as minutes : seconds. View the time • PRoGRAM PRoFILES: Represents the profile of the remaining or the time elapsed in your workout. -
Page 17: Getting Started
GETTING STARTED NOTE: If no TARgET or WORKOUT is selected, the program will function as a MANUAL program. All changes in speed 1) Check to make sure no objects are placed on the and incline will need to be from the user in this setting. belt that will hinder the movement of the treadmill. - Page 18 TARGET PRoFILES TARGET 1 – TIME: Allows user to set a target based on how long they would like to workout. Time targets can range from 15:00 – 99:00. TIME will count down. DISTANCE and CALORIES will count up from zero. TARGET 2 –...
- Page 19 3) WEIGHT LoSS – ALL MoDELS: Promotes weight loss by increasing and decreasing the speed, while keeping you in your fat burning zone. Segment Warm Up Time 4:00 Mins 30 sec 30 sec 30 sec 30 sec 30 sec 30 sec 30 sec 30 sec Segments 1–8 repeat...
-
Page 20: Finishing Your Workout
To RESET THE CoNSoLE Hold STOP key for 3 seconds. CooL DoWN Puts treadmill into cool down mode. Cool down lasts for four minutes and reduces speed and incline to allow your heart to readjust to decreased demand. FINISHING YoUR WoRKoUT When your workout is complete, the monitor display will flash “FINISHED”... - Page 21 ADVENTURE E EXPLoDED VIEW P13x2 Q33x4 V03x2 M40x4 M38x4 P14x4 P27x2 B35x8 M16x2 Q34x2 Z05x1 B31x8 M09x2 Z03x1 Z04x1 M07x2 Z04x2 B32x6 Z03x2 B28x8 Z05x2 P18x4 B48x2 Z09x4 B46x2 M11x2 B33x4 R04x2 Q32x2 Z05x2 Z02x2 Z05x1 Z03x2 Z02x2 Z03x2 Z03x1...
- Page 22 DESCRIPTION DESCRIPTION FRAME SET-EXTRAWORK;SCREEN PRINT;TM65 CONSOLE MAST SET;SEMI-ASSY;LEFT;TM657F FINISHED TREADMILL DECK;675X1220X18T;SI FIXED SET;CONSOLE MAST;L;PAINTINg;MM384 CUSHION;FIXINg;C;BLACK; CONSOLE MAST SET;SEMI-ASSY;RIgHT;TM657 FIXINg BUMPERC¡FBLACK¡FTM616-1US FIXED SET;CONSOLE MAST;R;PAINTINg;MM384 SCREW;FH;M8X1.25PX28L;HS;BP SUPPORT TUBE SET;CONSOLE MAST;M;PAINTINg SCREW;BUTTON HEAD;Φ4x10L;SHEET METAL THR RACK SET;PAINTINg;MM384-DARK SILVER;T ELASTOMER;DECORATIVE;FRONT;TPR;BLUE/301C NUT;NLK;M8X1.25P;BZN; ELASTOMER;L;INSIDE;422C;TM622 SCREW;M8X1.25PX9L-D10X11.2L;HE;45#;BOX SCREW;TRH;Φ4x12L;TC;PH;BAN;POT WASHER;FLT;Φ10.5xΦ20.0x1.0T;TFN;...
- Page 23 DESCRIPTION DESCRIPTION SCREW;SH;5/16"18UNCX16L;HS;BP MOTOR COVER SET;SEMI-ASSY;TM657F;SER WASHER;ARC;Φ8.2xΦ18.0x1.5T;BAN; COVER;MOTOR;DOWN;PP;TM639-1US SCREW;HEX HEAD;3/8-16UNCX45L-15L;BLAC SIDE RAIL;LEFT;PAINT;TM658;TOOLINg SHARI NUT;NYLOCK;3/8''-16UNC;BLACK ANNODIZED; COVER;SIDE RAIL;LEFT;BLACKE;TM626; WASHER;FLAT;Φx10.2xΦx19.0x2.0T;CHROME; END CAP;LEFT-REAR;75140;ABS;TM621;TOOL SCREW;HEX;M10X55L-14L;BED END CAP;RIgHT-REAR;75140;ABS;TM621;TOO NUT;NYLOCK;M10X1.5P;BLACK ANNODIZED; SCREW;TRH;Φ4x12L;TC;PH;BAN;POT CONSOLE SET;SEMI-ASSY;TM657F;SERVICE SCREW;TRHW;Φx4x20L;TC;PH;BED;POT; SAFETY KEY;ASSEMBLY;TM622 SCREW;BH;Φ4x25L;SM;PH;BZN;POT POWER SOCKET SET;CE(80,800,300);16AWg SIDE RAIL;RIgHT;PAINT;TM658;TOOLINg SHAR BREAKER;THROUgH ELECTRIC CURRENT;7A 250V COVER;SIDE RAIL;RIgHT;BLACKE;TM626;...
- Page 24 DESCRIPTION EXTERNAL PWR WIRE SET;ISRAEL;1.5MM;2 EXTERNAL PWR;IN;1.5MM;2M; EXTERNAL PWR;NEW ZEALAND;1.5MM;2M; EXTERNAL PWR;EUROPE;1.5MM;2M; EXTERNAL PWR;SWEDEN;2M;1.5MM EXTERNAL PWR;ARgENTINA;1.5MM;2M; EXTERNAL PWR;CHINA;1.5MM;2M EXTERNAL PWR;HK/KW/gB;1.5MM;2M; EXTERNAL PWR;JAPAN;1.5MM;2M; EXTERNAL PWR;BR;LENgTH:2M;1.5MM2 WIRE;EXTERNAL PWR;SET;CHILE USED;JIS2 U EXTERNAL PWR;TAIWAN;2.0MM2;2M;MEET T...
- Page 25 Horizon Fitness - Produkte sind recyclebar. Führen Sie das gerät am Ende der Nutzungsdauer einer sachgerechten Entsorgung zu (örtliche Sammelstelle). Gb: Waste Disposal Horizon Fitness products are recyclable. At the end if its useful life please dispose of this article correctly and safely (local refuse sites). F: Remarque relative à la gestion des dèchets Horizon Fitness sont recyclables.
- Page 28 TREADMILL OWNER’S MANUAL Adventure E Treadmill Owner’s Manual 061614’ Rev1.4 © 2014 Horizon Fitness...