Maintenance - Black & Decker BDPS400 Instruction Manual

36 • ENGLISH
f Remove the front housing of the sprayer, by pressing
down on the release button and pulling the front
housing off of the sprayer (Fig. P5, P6).
f Remove the piston and spring (Fig P7).
f Clean the spray nozzle, pickup tube and filter,
atomizer, piston and spring with the cleaning brush in
the appropriate cleaning solution (Fig. P8).
f Thoroughly clean the inside of the piston chamber
with the cleaning brush (Fig. P9).
Important! Be sure to remove all material from inside
of piston chamber. A small amount of material that is not
removed with the cleaning brush can harden over time and
interfere with the movement of the piston causing damage
to the sprayer.
f Ensure that quick clean knob is oriented in the spray
position as shown in Fig. P10 with an arrow.
f Thoroughly clean the inside of the intake and return
openings with the cleaning brush (Fig. P10).
Important! Also thoroughly clean the smaller vent hole,
shown with an arrow in Fig. P11, with included cleaning pin.
f Dry all parts thoroughly.
CLEANING THE DIRECT TO CAN HOSE:
f Unplug the sprayer from the power source.
f Remove the suction tube from the material container
and submerge into a bucket containing solvent
appropriate to the type of material you sprayed (warm,
soapy water for latex-based materials; manufacturers
recommended cleaning solution for oil based
materials (Fig. Q).
f Plug in sprayer. Point sprayer into the side of another
waste container. Trigger the sprayer until the spray
pattern turns to only the color of the cleaning solution
(Fig. Q1).
f Unplug the sprayer from the power source.
f Remove the tubing from the intake and return ports
(Fig. Q2).
f Hold the tubing over the waste container and let any
remaining liquid in the hose drain out.
REASSEMBLy
f Slide the spring onto the front of the piston (Fig. R).
f Insert the piston and spring into the front housing
(Fig. R1).
f Pressing down on the release button, insert the front
housing with piston, into the sprayer until the release
button pops into place (Fig. R2).
Notice! The unit will not reassemble with- out the
piston and spring in place.
f Place a few drops of oil through the cylinder opening.
Insert the atomizer valve into the front housing.
Thread the spray nozzle onto the front housing and
hand tighten (Fig R3).
f Using the oil lubricant provided, place a few drops of
oil down the intake and return openings of the sprayer
as shown in Fig R4.
f Rotate the quick clean lever from paint to clean and
back 3 times after oiling.
f Insert the pickup tube into the intake opening on the
sprayer (Fig. R5).
f Thread the canister back onto the sprayer (Fig. R6)
making sure the tabs on the canister align with the
tabs on the threaded collar. The side fill lid should
always be on the left side of the sprayer.

MAINTENANCE

Use only mild soap and damp cloth to clean the power
unit. Never let any liquid get inside the power unit; never
immerse any part of the power unit into a liquid.
Important! To assure product SAFETy and RELIABILITy,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service organizations,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product are
available from your local dealer or authorized service center.
Warning! The use of any accessory not recommended
for use with this product could be hazardous.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black &
Decker product needs replacement, or if it is of
no further use to you, do not dispose of it with
household waste. Make this product available for
separate collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials. Local regulations may
provide for separate collection of electrical products
from the household, at municipal waste sites or by
the retailer when you purchase a new product.