Camera Network Camera Quick Guide UD.6L0201D0186A01...
Page 2
Network Camera·Quick Guide Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. This manual applies to DS-2CD2612F-I(S), DS-2CD2632F-I(S) cameras. This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice.
Network Camera·Quick Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Page 4
Network Camera·Quick Guide equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information.
Network Camera·Quick Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
Page 6
Network Camera·Quick Guide To reduce the risk of fire or electrical shock, do not expose this product to rain or moisture. This installation should be made by a qualified service person and should conform to all the local codes. ...
Page 7
Network Camera·Quick Guide Do not place the camera in extremely hot, cold temperatures (the operating temperature should be between -30°C ~ 60°C), dusty or damp environment, and do not expose it to high electromagnetic radiation. To avoid heat accumulation, good ventilation is required for a proper operating environment.
Network Camera·Quick Guide Overview Appearance Figure 1-1 Overview Table 1-1 Overview Description Sun Shield Front Cover Zoom and Focus Lever...
Page 10
Network Camera·Quick Guide IR LED Lens Air Vent Video Output Interface Integrated Bracket Reset Button SD Card Slot Power Interface Network Interface Notes: To reset the default parameters to the camera, you need to press and hold the reset button and power on the camera. After the power on the camera, you must still press and hold the reset button for about 10 seconds.
Network Camera·Quick Guide Installation Before mounting, please make sure that the device in the package is in good condition and all the assembly parts are included. Notes: Please make sure that the device in the package is in good condition and all the assembly parts are included.
Page 13
Network Camera·Quick Guide Remove the front cover by rotating it counterclockwise as shown in Figure 2-1(right). Figure 2-1 Disassemble the Camera Insert the SD card to the SD card slot. Rotate the front cover clockwise back to the camera and install the sun shield according to the arrow direction as shown in Figure 2-2(right).
Network Camera·Quick Guide Slide the sun shield according to the arrow direction as shown in Figure 2-3(left). Rotate the TW M3X5 screw clockwise to tighten the sun shield. Rotating Label Figure 2-3 Assemble the Camera Note: For water-proof, please align the rotating label on the front cover with that on the camera when you rotate the front cover clockwise.
Page 15
Network Camera·Quick Guide 1. Attach the drill template (supplied) to the wall where the camera is to be mounted. Drill screw holes in the wall according to the number one holes of the drill template. Refer to the Figure 2-4. Screw Hole Cable Hole 2:Screw Hole...
Network Camera·Quick Guide Route the cables of the camera. Secure the camera to the wall(or ceiling) with expansion screws. Refer to the Figure 2-5. Figure 2-5 Secure the Camera Wall Mounting with a Junction Box Before you start: For mounting with a junction box, you have to purchase a junction box. Steps:...
Page 17
Network Camera·Quick Guide 1. Attach the drill template (supplied) to the wall where the camera is to be mounted. Drill holes in the wall according to the number two holes of the drill template. Refer to the Figure 2-4. If you need to route cables through the wall(or ceiling), cut a cable hole according to the drill template.
Network Camera·Quick Guide Figure 2-6 Secure the Camera Wall Mounting with a Gang Box Before you start: For mounting with a gang box, you have to purchase a gang box. Steps: 1. Secure the camera attachment to a gang box with screws. Route the cables of the camera.
Page 19
Network Camera·Quick Guide 3-axis (pan/tilt/rotation) adjusting allows adjustment for optimum camera rotation and placement. You can use this function to get the angle of view that you want. Pan Adjustment Steps: 1. Loosen the lock screw-1. Adjust the panning position of the camera. The adjusting range is from 0 degrees to 360 degrees.
Network Camera·Quick Guide Lock Screw-1 Rotation Lock Screw-2 Tilt Lock Screw-3 Figure 2-8 Lens Adjustment Zoom and Focus Adjusting Purpose: You can use the zoom lever and focus lever to adjust the zoom value and focus value. Steps: 1. Disassemble the camera. Refer to section 2.1. 2.
Page 21
Network Camera·Quick Guide Lever Lever Figure 2-9 Zoom and Focus Adjustment...
Network Camera·Quick Guide Setting the Network Camera over the LAN Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP or iVMS-4200 software to search and change the IP of network camera. ...
Page 23
Network Camera·Quick Guide 2. Change the IP address and subnet mask to the same subnet as of your PC. Refer to the following introductions to set IP address with SADP software: Search active devices online Search online devices automatically: After launch the SADP software, it automatically searches the online devices every 15 seconds from the subnet where your computer locates.
Page 24
Network Camera·Quick Guide Note: Device can be searched and displayed in the list in 15 seconds after it goes online; it will be removed from the list in 45 seconds after it goes offline. Search online devices manually: You can also click to refresh the online device list manually.
Page 25
Network Camera·Quick Guide 3). Enter the password of the admin account of the device in the Password field and click to save the changes. Figure 3-3 Select a device Figure 3-4 Modify Network Parameters...
Page 26
Network Camera·Quick Guide Enter the IP address of network camera in the address field of the web browser to view the live video. Notes: The default value of the IP address is 192.0.0.64. The default user name is admin, and password is 12345. ...
Network Camera·Quick Guide Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 7.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 3.5 and above version and Google Chrome8 and...
Page 28
Network Camera·Quick Guide Figure 4-1 Login Interface Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.
Page 31
Network Camera·Quick Guide Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to login. Note: For detailed instructions of further configuration, please refer to the user manual of network camera.