Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NETGEAR ANT24D18v2
Summary of Contents for NETGEAR ANT24D18v2
- Page 1 14 dBi Patch Panel Directional Antenna ANT24D18v2 Installation Guide...
-
Page 2: Package Contents
Introduction Thank you for purchasing the NETGEAR ANT24D18v2 antenna. This Installation Guide provides installing instructions and guidelines for using the NETGEAR 14 dBi Patch Panel Directional Antenna. Package Contents Reverse N/SMA adapter 14 dBi Patch Panel Directional Installation Guide, Warranty and... -
Page 3: Pole Mount Configuration
To obtain optimal results in extending wireless range with antenna installations, consult a qualified professional installer for site survey and installation assistance. In the U.S., the ANT24D18v2 antenna should only be used with devices that have been FCC approved for use with it. Please check the NETGEAR web site at http://www.NETGEAR.com/go/antennas_fcc for an updated list of FCC approved devices. -
Page 4: Placement And Other Important Considerations
Provide a good visual office with low ceiling): WLAN communication can suffer from multiple reflections line of sight between the ANT24D18v2 and the other antenna (max. open space) and ideally which are environment, orientation and time dependent, called multipath fading. In no partial obstruction. -
Page 5: Pole Mount Installation
The best performance is achieved with a short cable between the antenna and the wireless Mount the antenna on a pole, or on a wall with adjustable brackets, or on a wall with device. The shortest approved cable to be used in conjunction with the ANT24D18v2 in fixed brackets. -
Page 6: Now, Connect The Antenna
Connect a NETGEAR cable model ACC-10314-01, 02, 03, 04 or 05 (sold separat ely) to the adapter. Locate the primary detachable antenna on the wireless access point. Remove the antenna and connect the other end of the NETGEAR cable ACC-10314-01, 02, 03, 04 or 05 to this port. -
Page 7: Connecting The Antenna For An Indoor Installation
If connecting 2 ANT24D18v2 antennas: repeat step 2 to 5 for the second antenna and connect it the secondary port. If the wireless device supports transmit/receive on both Note: On access points with two antennas, if you are only replacing one antenna, be sure to replace the primary antenna and do not remove the secondary antenna. -
Page 8: Specifications
Specifications This chapter provides the 14 dBi Patch Panel 14 dBi Patch Panel Directional Directional Antenna Antenna specifications. ANT24D18v2 and 2m cable Hardware 14 dBi Patch Panel Directional Antenna Description Description 2 Meter Antenna Cable and Mounting Assembly Frequency Range... -
Page 9: Lightning Arrestor
N/SMA Adapter Accessory Lightning arrestor Description Lightning Arrestor Description N/SMA Adapter Accessory 0 - 6 GHz 0 - 3 GHz Frequency Range Frequency Range VSWR 1.5 max. VSWR 1.5 max. Connector Type N type Male reverse to SMA Female reverse Insertion Loss 1.3 dB max. -
Page 10: Radiation Pattern: Elevation (Vertical Plane)
2. This device must accept any interference received, including interference that may cause undesired operation. In the U.S., the ANT24D18v2 antenna should only be used with devices that have been FCC approved for use with it. Please check the NETGEAR web site at http://www.NETGEAR.com/go/antannas_fcc for an updated list of FCC approved devices. -
Page 12: Technical Support
2004 NETGEAR, Inc. NETGEAR, the Netgear logo, ProSafe, Auto Uplink and Everybody's connecting are trademarks or registered trademarks of Netgear, Inc. in the United States and/or other countries. Other brand and product names are trademarks or registered trademarks of their respective holder. Information is subject to change without notice.