Honeywell Lynx Plus Quick Manual To User Functions page 2

Checking Open Zones or System Status
Checking Zones: Before arming your system, all protected doors, windows and other
detection zones must be closed or bypassed; otherwise the keypad displays "Disarmed Not
Ready."
Function Press these keys...
Check General
 Announces general system status.
System Status STATUS
Zones
STATUS (2 times)  Displays system status and announces zone
Check Specific
faults.
(second depression must be
System Status
made within 10 seconds)
Arming the System
Before arming, close all perimeter doors and windows and make sure the "Ready to Arm"
message is displayed. Enter the 4-digit Security Code and select the desired key. The system
will beep three times to confirm the arming and will display the armed status.
After arming, leave the premises through an entry/exit door during the exit delay period and
be sure the door is reclosed to avoid causing an alarm.
When to use an arming mode
Mode Press these keys...
 Used to arm the system when persons are staying
inside (or if you have pets that are moving
throughout the premises).
User Code + STAY
Stay  Arms perimeter zones; interior zones left
disarmed.
 An alarm sounds if any protected window or non-
entry/exit door is opened.
 Used when staying inside and you do not expect
anyone to use an entry/exit door.
User Code + STAY +
Instant Stay  Same as Stay mode, except entry delay is Off.
NO DELAY
 An alarm sounds same as Stay mode, and sounds
upon opening entry/exit doors.
 Used when premises is vacant (including pets).
 Arms the entire system (interior and perimeter).
Away User Code + AWAY
 An alarm sounds if a protected window or any
door is opened, or if any movement is detected.
 If programmed, you can press the Quick Arm
Quick STAY OR AWAY
button in place of your security code when arming
Arming (for at least 2 seconds)
the system
Disarming the System and Silencing Alarms
The OFF key is used to disarm the system, silence alarm and trouble sounds, and clear
memory of alarm displays. Enter the 4-digit Security Code and select the OFF key.
Mode Press these keys ...
 System is disarmed and alarm sounding is
Disarm & User Code + OFF
silenced.
Silence
OR User Code
 To clear the memory of alarm display (if present),
Alarms (If Quick Disarm is active)
enter a second Off Sequence.
Bypassing Zones
Select the BYPASS key when you want to arm your system with one or more zones
intentionally unprotected. The system must be disarmed first.
Mode Press these keys...
 When finished, the keypad will provide a
confirmation beep and "Bypass" will be displayed
along with each bypassed Zone Number.
 When armed, the arming message is displayed
Bypass User Code + BYPASS
with "Bypass."
Individual + 2-digit zone number
 Bypassed zones are unprotected and will not
Zone(s)
(s)
trigger an alarm if violated.
 Fire zones cannot be bypassed.
 Bypasses are automatically removed when the
system is disarmed.
 All open (faulted) zones are bypassed (if
User Code + BYPASS +
Bypass all
programmed).
Open Zones
FUNCTION
Display  "Bypass" will be displayed along with each
User Code + BYPASS
Bypassed bypassed Zone Number
+ wait
Zones
21
What happens
20
19
18
17
and what happens
16
15
Index Item
1 Display Window
2 ARMED (Red)
LED Indicator
3 READY (Green)
LED Indicator
4 PLAY key
5 STAY/DELETE
key
What happens
6 AUX/Select key
7 BYPASS key
8 CHIME key
9 FUNCTION key
10 Microphone
11 NO DELAY key
What happens
12 CODE key
13 STATUS key
14 LIGHTS ON key
15 TEST key
16 LIGHTS OFF key
17 Speaker
18 AWAY/ADD key
19 OFF/ESCAPE key
20 RECORD key
21 0 -9 keys
1 2 3
ARMED READY
OFF 1 2 3 STAY
ESCAPE RECORD VOLUME PLAY DELETE
4 5 6
AWAY AUX
ADD LIGHTS ON TEST BYPASS SELECT
7 8 9
LIGHTS OFF CODE CHIME
0
STATUS NO DELAY FUNCTION
14 14 13 12 11 10 9
Description
Liquid Crystal Display (LCD). Displays protection point identification ,
system status, messages, and user instructions.
ON = System is armed (Stay or Away)
OFF = System is disarmed
Blinking = System is armed, and not ready to be armed (an alarm has
occurred)
Blinking once per second = AVM (VOX or Talk) or speaker phone mode is
active
ON = system is ready to be armed
OFF = System is armed
Blinking = System is disarmed, and not ready to be armed (a fault exists)
Blinking once per second = AVM (VOX or Talk) or speaker phone mode is
active
Play a recorded message or increase volume of voice messages.
Arms the perimeter burglary protection, (but not the motion sensor) or to
delete messages.
Program/perform a predefined function or to send a preset message to a
pager or "Follow Me" system phone number.
Bypasses individual protection zones or to decrease volume of voice
messages.
Turns the Chime mode On or Off.
Allows alternate key functions or as a "repeat" key during Clock/Calendar
setting.
Used to record personal messages via the Message Center, and for two-
way voice and speaker phone operation.
Used with STAY or AWAY function to bypass the entry delay
Allows entry of User Codes for additional system users
Use to display all open zones and announce system status when system is
disarmed
Turns lights or other devices On, if programmed by the installer
Tests the system and alarm sounder
Turns lights or other devices Off, if programmed by the installer
Source of alarms, audible internal warning and confirmation sounds, status
announcements, as well as alarms (Refer to the full User Guide for details)
Completely arms perimeter and interior burglary protection or to accept
entries in specific programming modes.
Disarms the burglary portion of the system, silences alarms and audible
trouble indicators, and clears alarm trouble display after the problem has
been corrected. Also used to exit/abort "Follow Me" phone number and
Clock/Calendar mode.
Activates the recording function to record personal messages.
Used to enter your individual security access code(s).
System Settings
Your system settings including volume level (message playback, system announcements,
and status beeps). Additionally, you can turn On/Off the Chime, Telephone Ringer and/or
System Voice Announcements.
4
Note: To enable or disable the Chime mode the system must be disarmed.
Mode Press these Keys...
Mute System
FUNCTION + VOLUME
5 Announcements
+ OFF
Restore System
6
Announcements FUNCTION + VOLUME
OR + 3 OR 6
Adjust Volume
Chime
Mode
FUNCTION + CHIME
7
8 Ringer Mode # + VOLUME + AUX
Security Codes
Your installer assigned a master code that is used to perform all system functions.
1000-300-013-V0
In addition, security codes can be assigned for up to 6 users. Only the Master User can
assign security codes to users. Note that User No. 07 is assigned to the Babysitter Code and
User No. 08 is the Duress Code.
To Add/Edit/Delete User Codes:
Follow the steps below:
Function
Enter Master User Code + CODE + User Number (03-08) + User Code
Add User Code
(Keypad beeps once confirming User Code addition)
Delete User Enter Master User Code + CODE + User Number (03-08)
Code (Keypad beeps once confirming User Code deletion)
Enter Master User Code + CODE + Master User Number (02) + New
Change Master
User Code (2 times)
User Code
(Keypad beeps 3 times confirming Master User Code change)
Panic Keys
Your system may have been programmed to use special keys to manually activate
emergency (panic) functions.
To activate a Panic Function:
Press and hold down the both keys of the Panic key pair for at least 2 seconds.
* All panic functions send signals to the Central Monitoring Station, if connected.
The functions that might be programmed are listed below. See your installer for the
function(s) that may have been programmed for your system.
functions that are active in your system.
Keys Zone
1 and  95
3 and # 96
 and # 99
What happens
 Disables the Voice announcement of
system status.
 Enables the Voice announcement of system
status.
 Adjusts the volume of the Voice
announcements.
 Alerts you to the opening of a perimeter
door or window while the system is
disarmed.
 Open (faulted) zone information is
displayed.
 Three tones sound at the keypad whenever
a perimeter door or window is opened
(faulted interior zones do not produce a
tone).
 Enables or disables the Telephone Ringer.
Perform the following...
Your Installer should note the
Sends this Signal*