Changing The Display Brightness; Turning Line Direct On And Off; Making Sounds Natural; Changing The Source Name - JVC RX-DP10VBK Instructions Manual

Changing the Display Brightness

You can dim the display.
Press DIMMER.
• Each time you press the button, the brightness level of the display
changes as follows:
D I M M E R
On the unit
Dimmer
Canceled
(Normal display)
Note:
Even though the dimmer is in use, the display brightens for a while
when you operate the receiver (except when changing the source).

Turning Line Direct On and Off

You can enjoy the sound closer to original source by skipping the
sound adjustments such as Midnight mode (see page 38), speaker
output level adjustments (see page 44) and Parametric Equalizer (see
page 44). You can only adjust the volume level while Line Direct is
in use.
• You have to make this setting for each source.
Press LINE DIRECT.
• Each time you press the button, Line Direct turns on and off.
– When Line Direct turns on, "LINE DIRECT" appears in the
main display.
LINE DIRECT
On the unit
(inside the front door)
ANALOG
L R
SUBWFR
Ex. When the source is "VIDEO."
Notes:
• This function is applied only to the main room sources.
• If you turn on Line Direct while using the Surround and DSP
modes, the effect changes as follows:
Mode
Surround
Input
Analog Not valid
Digital
• If you turn on Line Direct, CC Converter (see the right column) is
canceled.
• Turning off Line Direct activates the sound adjustments previously
selected such as Midnight mode, speaker output level adjustments
and Parametric Equalizer.
• If you turn off Line Direct while listening to an analog source,
muting time* will be a little longer. (* The period during which no
sound comes out.)
25
DIMMER
On the remote control
Much dimmer
LINE DIRECT
On the remote control
SPEAKERS 1
VOLUME
DSP
Not valid
Valid Not valid

Making Sounds Natural

JVC's CC (Compensative Compression) Converter eliminates jitter
and ripples, achieving a drastic reduction in digital distortion by
processing the digital music data in 24 bit–quantization and by
expanding the sampling frequency to 176.4 kHz (for fs 44.1 kHz
signals)/192 kHz (for fs 48 kHz signals).
By using the CC Converter, you can obtain a natural sound field
from any source.
Press CC CONVERTER so that the CC
CONVERTER lamp lights up.
• Each time you press the button, CC Converter turns on and off (the
lamp goes off) alternately.
CC CONVERTER
On the unit
Note:
• This function is applied only to the main room sources.
• You cannot use this function while Line Direct or THX Surround is in
use. If you turn on Line Direct or THX Surround while this function
is in use, this function will be canceled.

Changing the Source Name

When you have connected an MD recorder to the TAPE/MD jacks
or the DBS tuner to the TV SOUND/DBS jacks on the rear panel,
change the source name which will be shown on the display when
you select the MD recorder or DBS tuner as the source.
On the unit ONLY:
When changing the source name from "TAPE" to
"MD":
1. Press TAPE/MD.
2. Press and hold TAPE/MD until
"ASSGN. MD" appears on the display.
ANALOG
L R
SUBWFR
dB
When changing the source name from "TV " to
"DBS":
1. Press TV/DBS.
2. Press and hold TV/DBS until "ASSGN.
DBS" appears on the display.
ANALOG
L R
SUBWFR
To change the source name to "TAPE" or "TV," repeat the same
procedure above — press and hold TAPE/MD to select "TAPE," or
press and hold TV/DBS to select "TV" in step 2.
• While selecting "DBS" as the sub-room source, you cannot
change the source name to "TV."
CC CONVERTER
On the remote control
TAPE/MD
SPEAKERS 1
VOLUME
dB
TV/DBS
SPEAKERS 1
VOLUME
dB