Panasonic KX-FP85 Service Manual page 91

2.4.4. SERVICE FUNCTION TABLE
Code Function
501 Pause time set
502 Flash time
503 Dial speed select
510 VOX time
511 VOX sense
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
533 Setting the number of times that
massage transfer is redialed.
534 Setting the massage transfer/pager
call redial interval
550 Memory clear: To reset the value to the default one, except the top margin
(853) and left margin (854).
551 ROM check
552 DTMF single tone test
553 Monitor on FAX communication
select
554 Modem test
555 Scan check
556 Motor test
557 LED test
558 LCD test
559 Document jam detection select
561 KEY test
570 BREAK % select
571 ITS auto redial time set
572 ITS auto redial line disconnection
time set
573 Remote turn-on ring number set
580 TAM continuous tone detection
590 FAX auto redial time set
591 FAX auto redial time disconnection
time set
592 CNG transmit select
Set Value Effective Default
Range
X 100 msec 001~600
X 10 ms 01~99
1:10 pps 2:20 1, 2
pps
1:6 sec 2:4sec 1, 2
1:High 2:Low 1, 2
1:2100 Hz 1, 2
2:1100 Hz
1:ON 2:OFF 1, 2
1:ON 2:OFF 1, 2
1:0 km 2:1.8 1~4
km 3:3.6 km
4:7.2 km
1:0 km 2:1.8 1~4
km 3:3.6 km
4:7.2 km
00~99 00~99
001~999 sec 001~999
1:ON 2:OFF 1, 2
1:OFF 1~3
2:PHASE B
3:ALL
1:ON 2:OFF 1, 2
1:61% 2:67% 1, 2
X number of 00~99
times
X second 001~999
X number of 01~99
rings
1:ON 2:OFF 1, 2
X number of 00~99
times
X second 001~999
1:OFF 1~3
2:ALL
3:AUTO
91
Remarks
50 ----------
70 ----------
1 ----------
1 ----------
1 When the TAM (or EXT TAM) does not stop
recording the ICM because noise is detected on
the telephone line, change this setting to "LOW".
1 See Symptom/Countermeasure Table for long
distance and international calls in 2.3.5.1.5 THE
UNIT CAN COPY, BUT CANNOT EITHER
TRANSMIT/RECEIVE LONG DISTANCE OR
INTERNATIONL COMMUNICATIONS(P.51).
1 See Symptom/Countermeasure Table for long
distance and international calls in 2.3.5.1.5 THE
UNIT CAN COPY, BUT CANNOT EITHER
TRANSMIT/RECEIVE LONG DISTANCE OR
INTERNATIONL COMMUNICATIONS(P.51).
1 The resolution reverts to the default when
transmission is complete.
1 When the telephone station is far from the unit or
reception cannot be performed correctly, adjust
accordingly.
1 When the telephone station is far from the unit or
transmission cannot be performed correctly, adjust
accordingly.
03 Selects the number of times that message
transfer is redialed (not including the first dialing).
30 Sets the interval of message transfer/pager call
redial.
"START" input
See 2.5 TEST FUNCTIONS(P.103).
2 See 2.5 TEST FUNCTIONS(P.103).
1 Sets whether to monitor the line signal with the
unit´s speaker during FAX communication or not.
See 2.5 TEST FUNCTIONS(P.103).
See 2.5 TEST FUNCTIONS(P.103).
0 See 2.5 TEST FUNCTIONS(P.103).
See 2.5 TEST FUNCTIONS(P.103).
See 2.5 TEST FUNCTIONS(P.103).
1 See 2.2.1 DOCUMENT JAMS(P.28).
See 2.5 TEST FUNCTIONS(P.103).
1 Sets the % break of pulse dialing according PBX.
0 Selects the number of times that ITS is redialed
(not including the first dial).
30 Sets the interval of ITS redialing.
15 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
1 ON : Stops TAM operation when Dial tone, etc.
are detected.
2 Selects the number of redial times during FAX
communication (not including the first dial).
45 Sets the FAX redial interval during FAX
communication.
2 Lets you select the CNG output during FAX
transmission. ALL: CNG is output at phase A.
AUTO: CNG id output only when automatic dialing
is performed. OFF: CNG id not output at phase A.
Refer to 2.3.5.1.2 SOMETIME THERE IS A
TRANSMIT PROBLEM(P.49).
KX-FP85