Advertisement
I
Hor [Pixels]
PC system
PC98
VESA350
PC/AT
PC98
DOS/V
VGA 60Hz
VGA 72Hz
VGA 75Hz
VGA 85Hz
SVGA 56Hz
SVGA 60Hz
SVGA 72Hz
SVGA 75Hz
SVGA 85Hz
XGA 43Hz
XGA 60Hz
XGA 70Hz
XGA 75Hz
XGA 85Hz
SXGA 43Hz
SXGA 60Hz
SXGA 75Hz
SXGA 85Hz
UXGA 60Hz
Mac
MAC13
MAC16
MAC19
MAC21
Video system
Video
HDTV (1035i) 60Hz
HDTV (1035i) 59Hz
480p
720p 60Hz
720p 59Hz
1080i 60Hz
1080i 59Hz
1080 24sF
NTSC
PAL
SECAM
• The resolution for the input signals is listed in the above table.
• Even signals in the frequency range that can be input may not be displayed normally depending on the type of the signal.
• When a signal other than listed above is input, the image could be partially erased or an unneeded fold-over image could
appear.
• Some signals other than listed above can be displayed. But they may require adjustment.
• Even some of the signals listed above may require adjustment depending on the video board used.
• Composite sync (C
) and G on Sync signals cannot be handled depending on the devices connected.
S
• The VGA signal of the PC system could be displayed in 480p mode of the VIDEO system. (In this case, the projector enters
video menu mode when the MENU button is pressed.)
Ver [Lines]
H [kHz]
V [Hz]
640
350
37.86
84.13
640
400
24.83
56.42
640
480
31.47
59.94
640
480
37.86
72.81
640
480
37.50
75.00
640
480
43.27
85.01
800
600
35.16
56.25
800
600
37.88
60.32
800
600
48.08
72.19
800
600
46.88
75.00
800
600
53.67
85.06
1024
768/2
35.52
43.48
1024
768
48.36
60.00
1024
768
56.48
70.07
1024
768
60.02
75.03
1024
768
68.68
85.00
1280
1024/2
46.43
43.44
1280
1024
63.98
60.02
1280
1024
79.98
75.03
1280
1024
91.15
85.02
1600
1200
75.00
60.00
640
480
35.00
66.67
832
624
49.73
74.55
1024
768
60.24
74.93
1152
870
68.68
75.06
33.75
60.00
33.72
59.94
720
483
31.47
59.94
1280
720
45.00
60.00
1280
720
44.96
59.94
1920
1080/2
33.75
60.00
1920
1080/2
33.72
59.94
1920
1080
27.00
24.00
15.734
60
15.625
50
15.625
50
• Read thoroughly the manual that comes with each video device.
• Use the supplied video cable. An video cable with an S-video (Y/C) terminal is not supplied.
Y/C
VIDEO
R
P
/R-Y
R
G
Y
H
B
V
P
/B-Y
B
REMOTE
RS-232C
• Connect a composite image signal output device or Y/C (S-video) image output device.
• When connecting the S-video cable, refer to "How to attach the ferrite core" on page 29.
• When connecting a video device, use a TBC along with it, or one which has a built-in TBC.
• Use of an extension cable to connect a video device and the projector could cause video degradation.
• When a signal with much jitter is reproduced on a VCR, or special-effect playback is performed, the upper part of the image
or the image itself may be erased or distorted.
Advertisement
