JVC HR-XV38SAG Instructions Manual page 69

Dvd player & video cassette recorder
Hide thumbs Also See for HR-XV38SAG:
Table of Contents

Advertisement

TIMER RECORDING (VHS deck)
Timer recording won't work.
● The clock and/or the timer have been set incorrectly.
]Re-perform the clock and/or timer settings.
● The timer is not engaged.
]Press # and confirm that "#" is displayed on the front display
panel.
Timer programming is not possible.
● Timer recording is in progress.
]Timer programming can't be performed while a timer
recording is in progress. Wait until it finishes.
"
" on the front display panel won't stop blinking.
● The timer is engaged but there's no cassette loaded.
]Load a cassette with the record safety tab intact.
"
", "
" and "
" on the front display panel won't stop
blinking.
● The loaded cassette has had its record safety tab removed.
]Remove the cassette and cover the hole with adhesive tape, or
insert a cassette with the record safety tab intact.
● The end of the tape was reached during timer recording.
]The programme may not have been recorded in its entirety.
Next time make sure you have enough time on the tape to
record the entire programme.
]Turn off the timer mode by pressing timer button or next
operations cannot be carried on.
"
" blinks for 10 seconds and the Timer mode is
disengaged.
● # has been pressed when there are no programs in memory,
or the timer record information has been programmed
incorrectly.
]Check the programmed data and re-program as necessary,
then press # again.
The S
V
system does not timer-record properly.
HOW
IEW
● The unit's channel positions have been set incorrectly.
]Refer to "G-
/S
®
CODE
HOW
(
pg. 27) and re-perform the procedure.
"
" and "
" on the front display panel won't stop blinking.
● The end of the tape was reached during Instant Timer
Recording.
]The programme may not have been recorded in its entirety.
Next time make sure you have enough time on the tape to
record the entire programme.
"
", "
" and "
" on the front display panel won't stop
blinking.
● The loaded cassette has had its record safety tab removed.
]Remove the cassette and cover the hole with adhesive tape, or
insert a cassette with the record safety tab intact.
● The end of the tape was reached during Automatic Satellite
Programme Recording.
]The programme may not have been recorded in its entirety.
Next time make sure you have enough time on the tape to
record the entire programme.
]Turn off the timer mode by pressing REC LINK button or next
operations cannot be carried on.
V
Timer Programming"
TM
IEW
OTHER PROBLEMS
Whistling or howling is heard from the TV during camcorder
recording.
● The camcorder's microphone is too close to the TV.
]Position the camcorder so its microphone is away from the TV.
● The TV's volume is too high.
]Turn the TV's volume down.
When scanning channels, some of them are skipped over.
● Those channels have been designated to be skipped.
]If you need the skipped channels, restore them. (
Channel settings that were made manually seem to have
changed or disappeared.
● After the manual settings were made, Auto Channel Set was
performed.
]Perform the manual settings again.
No channels are stored in the unit's memory.
● The TV aerial cable was not connected to the unit when Auto
Set Up was performed.
]Turn off the unit once and connect the TV aerial cable to the
unit properly, then turn on the unit again. Then perform Auto
Set Up again. (
pg. 14)
ATTENTION
This unit contains microcomputers. External electronic noise
or interference could cause malfunctioning. In such cases,
switch the unit off and unplug the mains power cord. Then
plug it in again and turn the unit on. Take out the cassette.
After checking the cassette, operate the unit as usual.
69
EN
pg. 61)

Advertisement

Table of Contents
loading

Table of Contents