Basic Operations; Display Indication; Setup Menu - Pioneer DEH-3490UB Owner's Manual

Operating this unit
Part Operation
Press to recall preset stations.
h Press to select the next/pre-
a/b
vious folder.
Press to select an audio func-
i
AUDIO
tion.
Press to select different dis-
plays.
j
DISP/SCRL
Press and hold to turn dimmer
on or off.
Press to pause or resume play-
k
e
back.
FUNC-
l Press to select functions.
TION
Press to display the disc title,
track title, folder, or file list de-
pending on the source.
LIST/
m
Press to display the list de-
ENTER
pending on the source.
While in the operating menu,
press to control functions.

Display indication

1
3 5 7 8 9
2 4 6
Indicator State
! Tuner: band and frequency
! RDS: program service
name, PTY information and
Main dis-
other literal information
1
play sec-
! Built-in CD, USB storage
tion
device and iPod: elapsed
playback time and text in-
formation
The list function is being oper-
2
(list)
ated.
3 LOC
Local seek tuning is on.
4
(TA) TA function is on.
5 (TP) A TP station is tuned in.
(re-
6 Track or folder repeat is on.
peat)
Random play is on.
(ran-
The iPod source is selected
7
dom/shuf-
and the shuffle or shuffle all
fle)
function is on.
The sound retriever function is
8
(sound re-
on.
triever)
(iPod This unit's iPod function is op-
9
control) erated from your iPod.
Set up menu
When you turn the ignition switch to ON after in-
stallation, set up menu appears on the display.
You can set up the menu options below.
1 After installation of this unit, turn the
ignition switch to ON.
SET UP appears.
Operating this unit
2 Turn M.C. to switch to YES. Press M.C. to
select.
# If you do not operate for 30 seconds, the set up
menu will not be displayed.
# If you prefer not to set up at this time, turn M.C.
to switch to NO. Press to select.
If you select NO, you cannot set up in the set up
menu.
3 Perform the following procedures to set
the menu.
To proceed to the next menu option, you need to
confirm your selection.
CLOCK SET (setting the clock)
1 Turn M.C. to adjust hour.
2 Press M.C. to select minute.
3 Turn M.C. to adjust minute.
4 Press M.C. to confirm the selection.
FM STEP (FM tuning step)
Normally, the FM tuning step employed by seek
tuning is 50 kHz. When AF or TA is on, the tuning
step automatically changes to 100 kHz. It may be
preferable to set the tuning step to 50 kHz when
AF is on.
! The tuning step remains at 50 kHz during man-
ual tuning.
1 Turn M.C. to select the FM tuning step.
50 (50 kHz)—100 (100 kHz)
2 Press M.C. to confirm the selection.
MW STEP (MW tuning step)
The MW tuning step can be switched between
9 kHz and 10 kHz.
1 Turn M.C. to select the MW tuning step.
9 (9 kHz)—10 (10 kHz)
2 Press M.C. to confirm the selection.
DEMO (demo display setting)
1 Turn M.C. to set the demo display to on or off.
2 Press M.C. to confirm the selection.
QUIT appears.
4 To finish your settings, turn M.C. to select
YES. Press to select.
# If you prefer to change your setting again, turn
M.C. to switch to NO. Press to select.
Notes
! You can set up the menu options in the initial
settings. For details about the settings, refer
to Initial settings on page 8.
! You can cancel set up menu by pressing
SRC/OFF.

Basic operations

Important
! Handle gently when removing or attaching
the front panel.
! Avoid subjecting the front panel to excessive
shock.
! Keep the front panel out of direct sunlight
and high temperatures.
! To avoid damaging the device or vehicle inte-
rior, remove any cables and devices attached
to the front panel before detaching it.
Section
02
3
En