Sharp 13VT-K100 Service Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. TV VCR Combo
  5. 13VT-K100
  6. Service manual

Sharp 13VT-K100 Service Manual

Tv/vcr combination
Hide thumbs
Table of Contents

Advertisement

Quick Links

In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its
original condition and only parts identical to those specified should be used.
» IMPORTANT SERVICE SAFETY PRECAUTION .................................................................................... 2
» ELECTRICAL SPECIFICATIONS ............................................................................................................ 6
» LOCATION OF USER'S CONTROL ........................................................................................................ 7
» DISASSEMBLY AND REASSEMBLY ...................................................................................................... 9
» INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................. 12
» PRECAUTIONS IN REASSEMBLING ................................................................................................... 17
» FUNCTION OF MAJOR MECHANICAL PARTS .................................................................................... 18
» ADJUSTMENT OF THE VCR ELECTRICAL CIRCUITRY ..................................................................... 40
» TROUBLESHOOTING ........................................................................................................................... 42
» CHASSIS LAYOUT ................................................................................................................................ 55
» BLOCK DIAGRAM OF TV SECTION..................................................................................................... 57
» BLOCK DIAGRAM OF VCR SECTION ................................................................................................. 59
» OVERALL SCHEMATIC DIAGRAM ....................................................................................................... 69
» DESCRIPTION OF SCHEMATIC DIAGRAM ......................................................................................... 71
» PRINTED WIRING BOARD ASSEMBLIES ........................................................................................... 83
» REPLACEMENT PARTS LIST ............................................................................................................... 89
» PACKING OF THE SET ....................................................................................................................... 108
SHARP CORPORATION
SERVICE MANUAL
TV/VCR COMBINATION
Chassis No. B97B
MODELS
CONTENTS
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
1
13VT-K100/150
13VT-CK10
13VT-K100/150
13VT-CK10
S48O413VT-K10
Page

Advertisement

Table of Contents
loading

Related Manuals for Sharp 13VT-K100

Summary of Contents for Sharp 13VT-K100

  • Page 1: Table Of Contents

    13VT-K100/150 13VT-CK10 SERVICE MANUAL S48O413VT-K10 TV/VCR COMBINATION Chassis No. B97B 13VT-K100/150 13VT-CK10 MODELS In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its original condition and only parts identical to those specified should be used.

  • Page 2: Important Service Safety Precaution

    13VT-K100/150 13VT-CK10 IMPORTANT SERVICE SAFETY PRECAUTION Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines which follow: WARNING X-RADIATION AND HIGH VOLTAGE LIMITS 1. For continued safety, no modification of any circuit 1.

  • Page 3: Safety Notice

    13VT-K100/150 13VT-CK10 IMPORTANT SERVICE SAFETY PRECAUTION (Continued) » Connect the resistor connection to all exposed metal BEFORE RETURNING THE RECEIVER parts having a return to the chassis (antenna, metal (Fire & Shock Hazard) cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop...
  • Page 4 13VT-K100/150 13VT-CK10 PRECAUTIONS A PRENDRE LORS DE LA REPARATION Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. AVERTISSEMENT LIMITES DES RADIATIONS X ET DE LA HAUTE TENSION 1.
  • Page 5 13VT-K100/150 13VT-CK10 PRECAUTIONS A PRENDRE LORS DE LA REPARATION (Suite) » Toucher avec la sonde d'essai les pièces métalliques VERIFICATIONS CONTRE L'INCEN-DIE ET exposées qui présentent une voie de retour au LE CHOC ELECTRIQUE châssis (antenne, coffret métallique, tête des vis, Avant de rendre le récepteur à...

  • Page 6: Electrical Specifications

    13VT-K100/150 13VT-CK10 ELECTRICAL SPECIFICATIONS TV SECTION POWER INPUT: 120 V AC 60 Hz POWER RATING: 65 W PICTURE SIZE Width: 37.8 cm Height: 38.7 cm Depth: 38.2 cm CONVERGENCE: Magnetic SWEEP DEFLECTION: Magnetic FOCUS: Hi-Bi-Potential Electrostatic INTERMEDIATE FREQUENCIES Picture IF Carrier Frequency: 45.75 MHz...

  • Page 7: Location Of User's Control

    13VT-K100/150 13VT-CK10 LOCATION OF USER'S CONTROL Description Of Controls FRONT REAR...

  • Page 8: Remote Control Battery Installation

    13VT-K100/150 13VT-CK10 LOCATION OF USER'S CONTROL (Continued) Location Of Control’s Buttons (Remote Control) Remote Control Battery Installation Before using the television, prepare the Remote Control. » Remote the battery cover as shown and insert two batteries (size Battery Cover “AA”) making sure the polarity matches the (+) and (–) marks inside the battery conpartment.

  • Page 9: Disassembly And Reassembly

    13VT-K100/150 13VT-CK10 DISASSEMBLY AND REASSEMBLY 1. Remove the 7 rear cover fixing screws and detach the rear cover. 2. Take out the anode cap, CRT PWB, connectors K and M, coating earth, Speaker chip fixing screws and others. 3. Take out the main PWB unit and the VCR unit.
  • Page 10 13VT-K100/150 13VT-CK10 DISASSEMBLY AND REASSEMBLY (Continued) 5. Remove the 4 cassette housing control fixing screws, and detach the cassette housing control. 6. Remove the 2 mechanism chassis angle fixing screws, and remove the 1 head amp shielding case fixing screw.
  • Page 11 13VT-K100/150 13VT-CK10 DISASSEMBLY AND REASSEMBLY (Continued) For servicing any of the components inside, disconnect the lead dressing holder. Position the main PWB unit upright as shown below and connect the leads for starting the services. FRONT...

  • Page 12: Installation And Service Instructions

    13VT-K100/150 13VT-CK10 INSTALLATION AND SERVICE INSTRUCTIONS Note: (1) When performing any adjustments to resistor controls and transformers use non-metallic screwdriver or TV alignment tools. (2) Before performing adjustment, TV set must be on at least 15 minutes. CIRCUIT PROTECTION HIGH VOLTAGE CHECK The receiver is protected by a 4.0A fuse (F701), mounted...

  • Page 13: Service Mode

    13VT-K100/150 13VT-CK10 The K-series SHARP TV/VCR COMBINATION have most of the analog setup adjustments eliminated. Coil and variable resistor adjustments are now performed digitally by using the remote transmitter or set’s volume and channel change function buttons. Note: There are still a few analog adjustments in the K-series such as 120V adjust, focus, master screen voltage and coils in the picture IF/detector circuit.
  • Page 14 13VT-K100/150 13VT-CK10 Table - A ADJUSTMENT DATA ADJUSTMENT ITEM INTIAL VALUE RANGE COMMENTS PICTURE 0~63 TINT 0~77 COLOR 0~63 BRIGHT 0~63 SHARPNESS 0~13 VERTICAL PHASE H-PHASE 0~31 RF-AGC 0~63 V-AMP 0-63 PIF-VCO 0-127 R CUT-OFF 0~255 G CUT -OFF 0~255...

  • Page 15: Service Adjustment

    13VT-K100/150 13VT-CK10 SERVICE ADJUSTMENT VCO Adjustment White Balance Adjustment 1. Connect a digital voltmeter between pin (44) of IC401 1. Have unit receive a good local channel. and ground. 2. Enter the service mode. Select service adjustment 2. Select a good local channel.
  • Page 16 13VT-K100/150 13VT-CK10 Vertical-Size adjustment 1. Have unit receive a good local channel. 2. Enter the service mode and select service adjustment item "V-AMP". 3. While observing the top and bottom of the screen, adjust "V-AMP" data value to proper vertical size and linearity.

  • Page 17: Precautions In Reassembling

    13VT-K100/150 13VT-CK10 PRECAUTIONS IN REASSEMBLING MOUTING THE CASSETTE CONTROLLER Initial setting is indispensable before placing the cassette controller in the mechanism. The initial setting is made in two ways;electrical and mechanical. Electrical setting: Make a short-circuit between TP7701 and TP7702 and be sure that the mechanism is back to its initial setting position (*1).

  • Page 18: Function Of Major Mechanical Parts

    13VT-K100/150 13VT-CK10 FUNCTION OF MAJOR MECHANICAL PARTS (TOP VIEW) Take-up Pole Base Ass'y Automatic Head Cleaner Ass'y Drum Ass'y Drum Motor A/C Head Ass'y Fixing Guide Pinch Roller Lever Ass'y Full Erase Head Pinch Drive Supply Pole Reverse Guide Base Ass'y...

  • Page 19: Bottom View

    13VT-K100/150 13VT-CK10 FUNCTION OF MAJOR MECHANICAL PARTS (BOTTOM VIEW) Capstan D. D. Motor Drive Belt Slow Brake Shifter Master Cam Casecon Drive Gear Limiter Pulley Ass'y Clutch Lever Function Function Slow brake Limiter pulley ass’y Gets in contact with the capstan D.D. motor Transmits the power of the capstan D.D.

  • Page 20: Adjustment, Replacement And Assembly Of Mechanical Units

    13VT-K100/150 13VT-CK10 ADJUSTMENT, REPLACEMENT AND ASSEMBLY OF MECHANICAL UNITS The explanation given below relates to the on-site general service (field service) but it does not relates to the adjustment and replacement which need high-grade equipment, jigs and skill. For example, the drum assembling, replacement and adjustment service must be performed by the person who have finished the technical courses.
  • Page 21 13VT-K100/150 13VT-CK10 Jig ltem Part No. Code Configuration Remarks These tapes are especially used for electrical fine adjustment. Video Audio Hi-Fi Audio Track 10. Alignment Tape 525 Monoscope — 58µm VROATSV NTSC Color Bar — 58µm VROBBZGS 525 Monoscope —...
  • Page 22 13VT-K100/150 13VT-CK10 MAINTENANCE CHECK ITEMS AND EXECUTION TIME Perform the maintenance with the regular intervals as follows so as to maintain the quality of machine. Maintained 500 1000 1500 2000 3000 Possible symptom Remarks Parts hrs. hrs. hrs. hrs. hrs.
  • Page 23 13VT-K100/150 13VT-CK10 REMOVING AND INSTALLING THE CAS- Notes: SETTE HOUSING 1. When fitting the S/E sensor holder to the cassette controller frame L/R, take care. • Removal 2. Misengagement of teeth of casecon drive gear and 1. In the cassette eject mode, remove the cassette.
  • Page 24 13VT-K100/150 13VT-CK10 REEL DISK REPLACEMENT AND HEIGHT 4. Assemble the Sup main brake ass'y. CHECK Notes: • Removal 1. When installing the reel disk, take due care so that the 1. Remove the cassette housing control assembly. tension band ass'y is not deformed and grease does 2.
  • Page 25 13VT-K100/150 13VT-CK10 Note: Notes: Whenever replacing the reel disk, perform the height 1. Hold the torque gauge by hand so that it is not moved. checking and adjustment. 2. Do not keep the reel disk in lock state. Do not allow long-time measurement.
  • Page 26 13VT-K100/150 13VT-CK10 Notes: CHECKING AND ADJUSTMENT OF TAKE- 1. Hold the torque gauge by hand so that it is not moved. UP TORQUE IN VIDEO SEARCH REWIND 2. Do not keep the reel disk in lock state. Do not allow MODE long-time measurement.
  • Page 27 13VT-K100/150 13VT-CK10 CHECKING THE VIDEO SEARCH REWIND BACK TENSION • Remove the cassette housing control assembly. • After short-circuiting TP7701 and TP7702 pro- Tension gauge Pinch roller vided at the left on the main PWB, plug in the 900 - 1,200g power cord, then turn on the power.
  • Page 28 13VT-K100/150 13VT-CK10 2. Visually check to see if the right edge of the tension Tension pole adjuster adjusting range pole is within the 1.5 ± 0.25mm from the right edge of the Sup guide shaft. Tension pole adjuster Sup guide shaft Tension pole 1.5 ±...
  • Page 29 13VT-K100/150 13VT-CK10 • Adjustment • Checking the brake torque at the take-up side 1. If the indication of torque cassette meter is lower than the setting, shift the tension spring engagement to the part A. Torque gauge 2. If the indication of torque cassette meter is higher than the setting, shift the tension spring engagement to the part B.
  • Page 30 13VT-K100/150 13VT-CK10 3. Align the left end of gear of A/C head arm with the REPLACEMENT OF A/C (Audio/Control) HEAD punched mark of chassis, tentatively tighten the screws 1. Remove the cassette housing control assembly. 1 and 2 so as to ensure smooth motion of A/C head 2.
  • Page 31 13VT-K100/150 13VT-CK10 A/C HEAD HEIGHT ROUGH ADJUSTMENT HEIGHT ADJUSTMENT OF REVERSE GUIDE • Setting 1. Adjust the height from the mechanism chassis to the reverse guide lower flange to 13.38 mm, using the Azimuth screw reverse guide height adjustment jig, in tape loading state.
  • Page 32 13VT-K100/150 13VT-CK10 Notes: ADJUSTMENT OF TAPE DRIVE TRAIN 1. Previously set the tracking control in the center posi- 1. Tape run rough adjustment tion, and adjust the envelope waveform to maximum 1 Remove the cassette housing control assembly. with X value adjustment nut. Thereby the tape run 2 After shortcircuiting TP7701 and TP7702 provided rough adjustment is facilitated.
  • Page 33 13VT-K100/150 13VT-CK10 3. Tape run adjustment PB CHROMA 1 Connect the oscilloscope to PB CHROMA envelope Envelope output test point, set oscilloscope sync to EXT, trigger-input the PB CHROMA signal (head switch- ing pulse). 2 Rough adjustment of X value...
  • Page 34 13VT-K100/150 13VT-CK10 REPLACEMENT OF DRUM D.D. MOTOR REPLACEMENT OF THE CAPSTAN D.D. 1. Set the eject mode. (DIRECT DRIVE) MOTOR 2. Withdraw the main power plug from the socket. • Remove the mechanism from the main PWB (refer to Page10 "DISASSEMBLY AND REASSEMBLY" Re- •...
  • Page 35 13VT-K100/150 13VT-CK10 REPLACING THE UPPER AND LOWER DRUM ASSEMBLING OF PHASE MATCHING ASSEMBLY MECHANISM COMPONENTS • Assemble the phase matching mechanism com- • Replacement (Perform in the numerical order) ponents in the following order. 1 Remove the motor as stated in Page 34 D.D. motor 1.
  • Page 36 13VT-K100/150 13VT-CK10 1Insert Reverse Guide Lever Ass’y Insert reverse guide lever ass'y 2 Insert pinch drive cam Align here. Turn the reverse guide lever assembly counterclockwise Fit the pinch drive cam so that the notch of pinch to the stopper.
  • Page 37 13VT-K100/150 13VT-CK10 1. Make sure that the loading gear is at the point 1 as INSTALLING THE SHIFTER shown below. 2. Install, paying attention to 6 insertion points and 3 release points. Drum 3. For the phase matching at the insertion point 1, see Capstan the point 2 as shown below.
  • Page 38 13VT-K100/150 13VT-CK10 INSTALLING THE MASTER CAM (AT REAR REPLACEMENT OF LOADING MOTOR • Removal SIDE OF MECHANISM CHASSIS) 1. Make sure beforehand that the shifter is at the point as shown below. 2. Place the master cam in the position as shown below.
  • Page 39 13VT-K100/150 13VT-CK10 ASSEMBLY OF CASSETTE HOUSING 1. Drive Gear and R Drive angle ass’y MSPRT0381AJFJ Apply grease Apply grease Apply grease Figure 1-47. 2. Synchro Gear, Drive Gear L and Drive Gear R LANGF9592AJFW Top surface should be free from scratches or soil.

  • Page 40: Adjustment Of The Vcr Electrical Circuitry

    13VT-K100/150 13VT-CK10 ADJUSTMENT OF THE VCR ELECTRICAL CIRCUITRY Notes: » Before the adjustment: Electrical adjustments described here are often required after replacement of electronic components and mechanical parts such as video heads. Check that the mechanism and all electric components are in good working condition prior to the adjustments, otherwise adjustments can not be completed.
  • Page 41 13VT-K100/150 13VT-CK10 Test points layout of Main Unit. Figure 2-2. ADJUSTMENT OF EP STILL PIC- TURE VERTICAL SYNC 1. Playback the EP Self-recorded tape in the still mode. Measuring Monitor TV 2. Using the CH '/" (TR ± — ) buttons on the remote...

  • Page 42: Troubleshooting

    13VT-K100/150 13VT-CK10 TROUBLESHOOTING OF VCR SECTION...
  • Page 43 13VT-K100/150 13VT-CK10...
  • Page 44 13VT-K100/150 13VT-CK10...
  • Page 45 13VT-K100/150 13VT-CK10...
  • Page 46 13VT-K100/150 13VT-CK10...
  • Page 47 13VT-K100/150 13VT-CK10...
  • Page 48 13VT-K100/150 13VT-CK10...
  • Page 49 13VT-K100/150 13VT-CK10...
  • Page 50 13VT-K100/150 13VT-CK10...
  • Page 51 13VT-K100/150 13VT-CK10...
  • Page 52 13VT-K100/150 13VT-CK10 TROUBLESHOOTING OF TV SECTION...
  • Page 53 13VT-K100/150 13VT-CK10...
  • Page 54 13VT-K100/150 13VT-CK10...

  • Page 55: Chassis Layout

    13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 CHASSIS LAYOUT PWB-B PWB-D PWB-C PWB-A...

  • Page 56: Block Diagram Of Tv Section

    13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 BLOCK DIAGRAM OF TV SECTION...

  • Page 57: Block Diagram Of Vcr Section

    13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 BLOCK DIAGRAM OF VCR SECTION OVERALL BLOCK DIAGRAM...
  • Page 58 13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 BLOCK DIAGRAM OF VCR SECTION SERVO PROCESS BLOCK DIAGRAM...
  • Page 59 13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 BLOCK DIAGRAM OF VCR SECTION SYSTEM CONTROL BLOCK DIAGRAM SAFETY DEVICE BLOCK DIAGRAM...
  • Page 60 13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 BLOCK DIAGRAM OF VCR SECTION VIDEO SIGNAL FLOW BLOCK DIAGRAM...
  • Page 61 13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 BLOCK DIAGRAM OF VCR SECTION AUDIO BLOCK DIAGRAM...

  • Page 62: Overall Schematic Diagram

    13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 OVERALL SCHEMATIC DIAGRAM...

  • Page 63: Description Of Schematic Diagram

    13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 DESCRIPTION OF SECTION SCHEMATIC DIAGRAM SCHEMATIC DIAGRAM : CRT, FRONT AV Unit NOTE: WAVEFORM MEASUREMENT CONDI- 1. The unit of resistance "ohm" is omitted TIONS: (K:1000 ohms, M:1 Meg ohm). 1. Photographs taken on a standard gated color bar 2.
  • Page 64 13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 SCHEMATIC DIAGRAM : MAIN-1 Unit (TV Section)
  • Page 65 13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 SCHEMATIC DIAGRAM : MAIN-2 Unit (TV Section)
  • Page 66 13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 SCHEMATIC DIAGRAM : POWER Unit (TV Section)
  • Page 67 13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 SCHEMATIC DIAGRAM : MAIN Unit (VCR-1 Section) DTC124ES...
  • Page 68 13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 SCHEMATIC DIAGRAM : MAIN Unit (VCR-2 Section)

  • Page 69: Printed Wiring Board Assemblies

    13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 PRINTED WIRING BOARD ASSEMBLIES PWB-B: CRT Unit (Wiring Side) PWB-D: FRONT AV Unit (Wiring Side) PWB-C: POWER Unit (Wiring Side)
  • Page 70 13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 PWB-A: MAIN Unit (Wiring Side)
  • Page 71 13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 PWB-A: MAIN Unit (Chip Parts Side)

  • Page 72: Replacement Parts List

    Q2224 VSUN2113///-1 UN2113 D7703 RH-PX0252GEZZ Gp1S563 3. NO. DE PIECE 4. DESCRIPTION in USA: Contact your nearest SHARP Parts Distributor to order. For Q2227 VSUN2213///-1 UN2113 D7704 RH-PX0253GEZZ Gp1S94 in CANADA: Contact SHARP Electronics of Canada Limited location of SHARP Parts Distributor, Please call Toll-Free;...
  • Page 73 13VT-K100/150 13VT-CK10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-A: DUNTK9489WEV2 C343 VCCCCY1HH151J 150p Ceramic C351 VCKYCY1HB272K 2700p 50V Ceramic MAIN Unit (Continued) C352 VCEAEA1CW107M J L3102 VP-XF100K0000 Peaking 10µH C354 VCEA0A1CW477M J L3301 VP-MK101K0000 Peaking 100µH...
  • Page 74 13VT-K100/150 13VT-CK10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-A: DUNTK9489WEV2 C3104 VCKYCY1HB102K 1000p 50V Ceramic C3105 VCCCCY1HH221J 220p Ceramic MAIN Unit (Continued) C3107 VCKYCY1HF103Z 0.01 Ceramic C804 VCKYCY1EB103K 0.01 Ceramic C3108 VCEAKA0JW107M 6.3V C805 VCKYCY1EB103K 0.01...
  • Page 75 13VT-K100/150 13VT-CK10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code RESISTORS PWB-A: DUNTK9489WEV2 (M.Ox. : Metal Oxide.) MAIN Unit (Continued) VRN-MD2AL000J 0.1W Metal Film AA C6632 VCKYCY1HF103Z 0.01 Ceramic VRN-MD2AL000J 0.1W Metal Film AA C6633 VCKYCY1HF103Z 0.01...
  • Page 76 13VT-K100/150 13VT-CK10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-A: DUNTK9489WEV2 R454 VRD-RA2EE184J 180k 1/4W Carbon R456 VRN-MD2AL273J 27k 0.1W Metal Film AA MAIN Unit (Continued) R466 VRN-VV3AB1R5J Metal Film AA R207 VRN-MD2AL391J 390 0.1W...
  • Page 77 13VT-K100/150 13VT-CK10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-A: DUNTK9489WEV2 R3109 VRD-RA2BE152J 1.5k 1/8W Carbon R3110 VRN-MD2AL102J 0.1W Metal Film AA MAIN Unit (Continued) R3111 VRN-MD2AL103J 10k 0.1W Metal Film AA R2055 VRN-MD2AL472J 4.7k 0.1W...
  • Page 78 13VT-K100/150 13VT-CK10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-A: DUNTK9489WEV2 R7743 VRD-RA2BE103J 10k 1/8W Carbon R7744 VRD-RA2BE103J 10k 1/8W Carbon MAIN Unit (Continued) R7745 VRD-RA2BE103J 10k 1/8W Carbon R5501 VRN-MD2AL122J 1.2k 0.1W Metal Film AA...
  • Page 79 13VT-K100/150 13VT-CK10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-A: DUNTK9489WEV2 P651 QPLGN0361CEZZ Plug 3-pin (TP651-3) P703 QPLGN0461CEZZ Plug 4-pin (YC) MAIN Unit (Continued) P2201 QPLGN0361CEZZ Plug 3-pin R7807 VRG-SC2EB1R8J 1/4W (TP2201-2, TP6601) Fuse Resistor...
  • Page 80 13VT-K100/150 13VT-CK10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code CAPACITORS PWB-C: DUNTK9490WEV2 (EL. : Electrolytic, M-Poly. : Metalized Polypro Film) POWER Unit å C702 VCKYPB2HE103P 0.01 500V Ceramic INTEGRATED CIRCUITS å C703 VCKYPB2HE103P 0.01 500V Ceramic å...

  • Page 81: Crt Unit

    13VT-K100/150 13VT-CK10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-C: DUNTK9490WEV2 PWB-B: DUNTK8606WEV4 POWER Unit CRT Unit (Continued) TRANSISTORS R743 VRD-RM2HD823J 82k 1/2W Carbon R744 VRD-RA2BE332J 3.3k 1/8W Carbon Q852 VS2SC2229O/1E 2SC2229 (O) R745 VRD-RA2BE332J 3.3k 1/8W...
  • Page 82 13VT-K100/150 13VT-CK10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code QCNW-0272AJZZ FFC for A/C Head MECHANISM CHASSIS QPWBF5469AJZZ A/C Head PWB QSOCN0605REN1 V Socket, 6 pin LBNDK1011AJZZ Tension Band Ass’y RHEDT0036AJZZ Full Erase Head LBOSZ1007AJZZ Tension Arm boss RHEDU0088GEZZ A/C Head Ass’y...
  • Page 83 13VT-K100/150 13VT-CK10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code MECHANISM CHASSIS PARTS...
  • Page 84 13VT-K100/150 13VT-CK10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code CASSETTE HOUSING CONTROL CHLDX3081TEV1 Cassette Housing LANGF9592AJFW Upper Plate LHLDX1028AJ00 Frame (L) LHLDX1032AJ00 Frame (R) LHLDX1030AJZZ Holder (L) LHLDX1031AJZZ Holder (R) MLEVF0469AJFW Proof Lever (R) MLEVP0281AJ00...
  • Page 85 13VT-K100/150 13VT-CK10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code CHASSETTE HOUSING CONTROL PARTS...
  • Page 86 TCAUS0010PEZZ Caution Label (13VT-K100/150) 1-13 TCAUS0004PEZZ Caution Label (13VT-CK10) 1-14 TCAUS0013PEZZ Caution Label(13VT-CK10) AB GCABB2349PEKA Rear Cabinet (13VT-K100) BB GCABB2349PEKB Rear Cabinet (13VT-K150) BB GCABB2351PEKA Rear Cabinet (13VT-CK10) BB QACCD3051CESA AC Cord (13VT-K100/CK10) QACCD3055CESB AC Cord (13VT-K150) QCNW-2206PEZZ Connecting Cord...
  • Page 87 13VT-K100/150 13VT-K100/150 13VT-CK10 13VT-CK10 CABINET AND MECHANICAL PARTS PWB-B 1-11 1-13 1-14 PWB-A PWB-C 42 43 1-10 1-12 @ @ @ @ @ PWB-D...

  • Page 88: Packing Of The Set

    13VT-K100/150 13VT-K100/150 13VT/CK10 13VT/CK10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING OF THE SET PACKING PARTS • SETTING POSITIONS OF THE KNOBS SUPPLIED ACCESORIES (NOT REPLACEMENT ITEM) Power SW TGAN-0018PEZZ Guarantee Card SPAKC6317PEZZ –...
  • Page 89 13VT-K100/150 13VT-CK10 Memo...
  • Page 90 13VT-K100/150 13VT-CK10 COPYRIGHT © 1998 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

This manual is also suitable for:

13vt-ck1013vt-k150

Table of Contents