Sharp 13VT-L200 Service Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. TV VCR Combo
  5. 13VT-L200
  6. Service manual

Sharp 13VT-L200 Service Manual

Sharp tv vcr combo service manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its
original condition and only parts identical to those specified should be used.
» IMPORTANT SERVICE SAFETY PRECAUTION .................................................................................... 2
» ELECTRICAL SPECIFICATIONS ............................................................................................................ 6
» LOCATION OF USER'S CONTROL ........................................................................................................ 7
» DISASSEMBLY AND REASSEMBLY ...................................................................................................... 9
» INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................. 12
» PRECAUTIONS IN REASSEMBLING ................................................................................................... 17
» FUNCTION OF MAJOR MECHANICAL PARTS .................................................................................... 18
» ADJUSTMENT OF THE VCR ELECTRICAL CIRCUITRY .................................................................... 40
» TROUBLESHOOTING ........................................................................................................................... 43
» CHASSIS LAYOUT ................................................................................................................................ 56
» BLOCK DIAGRAM OF TV SECTION..................................................................................................... 58
» BLOCK DIAGRAM OF VCR SECTION ................................................................................................. 60
» OVERALL SCHEMATIC DIAGRAM ....................................................................................................... 70
» DESCRIPTION OF SCHEMATIC DIAGRAM ......................................................................................... 72
» PRINTED WIRING BOARD ASSEMBLIES ........................................................................................... 84
» REPLACEMENT PARTS LIST ............................................................................................................... 88
» PACKING OF THE SET ....................................................................................................................... 105
SHARP CORPORATION
SERVICE MANUAL
TV/VCR COMBINATION
Chassis No. B97B
MODEL
CONTENTS
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
1
13VT-L200
13VT-L200
S29D413VTL200
Page

Advertisement

Table of Contents
loading

Related Manuals for Sharp 13VT-L200

Summary of Contents for Sharp 13VT-L200

  • Page 1: Table Of Contents

    13VT-L200 SERVICE MANUAL S29D413VTL200 TV/VCR COMBINATION Chassis No. B97B 13VT-L200 MODEL In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its original condition and only parts identical to those specified should be used.

  • Page 2: Important Service Safety Precaution

    13VT-L200 IMPORTANT SERVICE SAFETY PRECAUTION Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines which follow: WARNING X-RADIATION AND HIGH VOLTAGE LIMITS 1. For continued safety, no modification of any circuit 1.
  • Page 3 13VT-L200 IMPORTANT SERVICE SAFETY PRECAUTION (Continued) » Connect the resistor connection to all exposed metal BEFORE RETURNING THE RECEIVER parts having a return to the chassis (antenna, metal (Fire & Shock Hazard) cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop Before returning the receiver to the user, perform across the resistor.
  • Page 4 13VT-L200 PRECAUTIONS A PRENDRE LORS DE LA REPARATION Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. AVERTISSEMENT LIMITES DES RADIATIONS X ET DE LA HAUTE TENSION 1.
  • Page 5 13VT-L200 PRECAUTIONS A PRENDRE LORS DE LA REPARATION (Suite) » Toucher avec la sonde d'essai les pièces métalliques VERIFICATIONS CONTRE L'INCEN-DIE ET exposées qui présentent une voie de retour au LE CHOC ELECTRIQUE châssis (antenne, coffret métallique, tête des vis, Avant de rendre le récepteur à...

  • Page 6: Electrical Specifications

    13VT-L200 ELECTRICAL SPECIFICATIONS TV SECTION POWER INPUT: 120 V AC 60 Hz POWER RATING: 65 W PICTURE SIZE Width: 37.8 cm Height: 38.7 cm Depth: 38.2 cm CONVERGENCE: Magnetic SWEEP DEFLECTION: Magnetic FOCUS: Hi-Bi-Potential Electrostatic INTERMEDIATE FREQUENCIES Picture IF Carrier Frequency: 45.75 MHz...

  • Page 7: Location Of User's Control

    13VT-L200 LOCATION OF USER'S CONTROL Description Of Controls FRONT REAR...

  • Page 8: Remote Control Battery Installation

    13VT-L200 LOCATION OF USER'S CONTROL (Continued) Location Of Control’s Buttons (Remote Control) Remote Control Battery Installation Before using the television, prepare the Remote Control. » Remote the battery cover as shown and insert two batteries (size Battery Cover “AA”) making sure the polarity matches the (+) and (–) marks inside the battery conpartment.

  • Page 9: Disassembly And Reassembly

    13VT-L200 DISASSEMBLY AND REASSEMBLY 1. Remove the 7 rear cover fixing screws and detach the rear cover. 2. Take out the anode cap, CRT PWB, connectors K and M, coating earth, Speaker chip fixing screws and others. 3. Take out the main PWB unit and the VCR unit.
  • Page 10 13VT-L200 DISASSEMBLY AND REASSEMBLY (Continued) 5. Remove the 4 cassette housing control fixing screws, and detach the cassette housing control. 6. Remove the 2 mechanism chassis angle fixing screws, and remove the 1 head amp shielding case fixing screw. 7. Remove the 3 mechanism chassis fixing screws, and detach the mechanism chassis from the main PWB.
  • Page 11 13VT-L200 DISASSEMBLY AND REASSEMBLY (Continued) For servicing any of the components inside, disconnect the lead dressing holder. Position the main PWB unit upright as shown below and connect the leads for starting the services. FRONT...

  • Page 12: Installation And Service Instructions

    13VT-L200 INSTALLATION AND SERVICE INSTRUCTIONS Note: (1) When performing any adjustments to resistor controls and transformers use non-metallic screwdriver or TV alignment tools. (2) Before performing adjustment, TV set must be on at least 15 minutes. CIRCUIT PROTECTION HIGH VOLTAGE CHECK The receiver is protected by a 4.0A fuse (F701), mounted...
  • Page 13 13VT-L200 The L-series SHARP TV/VCR COMBINATION have most of the analog setup adjustments eliminated. Coil and variable resistor adjustments are now performed digitally by using the remote controller or set’s volume and channel change function buttons. Note: There are still a few analog adjustments in the L-series such as 120V adjust, focus, master screen voltage and coils in the picture IF/detector circuit.
  • Page 14 13VT-L200 Table - A ADJUSTMENT DATA ADJUSTMENT ITEM INTIAL VALUE RANGE COMMENTS PICTURE 0~63 TINT 0~77 COLOR 0~63 BRIGHT 0~63 SHARPNESS 0~13 VERTICAL PHASE H-PHASE 0~31 RF-AGC 0~63 V-AMP 0~63 PIF-VCO 0~127 R CUT-OFF 0~255 G CUT -OFF 0~255 B CUT-OFF...

  • Page 15: Picture Adjustment

    13VT-L200 SERVICE ADJUSTMENT VCO Adjustment White Balance Adjustment 1. Connect a digital voltmeter between pin (44) of IC401 1. Have unit receive a good local channel. and ground. 2. Enter the service mode. Select service adjustment 2. Select a good local channel.
  • Page 16 13VT-L200 Vertical-Size adjustment 1. Have unit receive a good local channel. 2. Enter the service mode and select service adjustment item "V-AMP". 3. While observing the top and bottom of the screen, adjust "V-AMP" data value to proper vertical size and linearity.

  • Page 17: Precautions In Reassembling

    13VT-L200 PRECAUTIONS IN REASSEMBLING MOUTING THE CASSETTE CONTROLLER Initial setting is indispensable before placing the cassette controller in the mechanism. The initial setting is made in two ways;electrical and mechanical. Electrical setting: Make a short-circuit between TP7701 and TP7702 and be sure that the mechanism is back to its initial setting position (*1).

  • Page 18: Function Of Major Mechanical Parts

    13VT-L200 FUNCTION OF MAJOR MECHANICAL PARTS (TOP VIEW) Take-up Pole Base Ass'y Automatic Head Cleaner Ass'y Drum Ass'y Drum Motor A/C Head Ass'y Fixing Guide Pinch Roller Lever Ass'y Full Erase Head Pinch Drive Supply Pole Reverse Guide Base Ass'y...

  • Page 19: Bottom View

    13VT-L200 FUNCTION OF MAJOR MECHANICAL PARTS (BOTTOM VIEW) Capstan D. D. Motor Drive Belt Slow Brake Shifter Master Cam Casecon Drive Gear Limiter Pulley Ass'y Clutch Lever Function Function Slow brake Limiter pulley ass’y Gets in contact with the capstan D.D. motor Transmits the power of the capstan D.D.

  • Page 20: Adjustment, Replacement And Assembly Of Mechanical Units

    13VT-L200 ADJUSTMENT, REPLACEMENT AND ASSEMBLY OF MECHANICAL UNITS The explanation given below relates to the on-site general service (field service) but it does not relates to the adjustment and replacement which need high-grade equipment, jigs and skill. For example, the drum assembling, replacement and adjustment service must be performed by the person who have finished the technical courses.
  • Page 21 13VT-L200 Jig ltem Part No. Code Configuration Remarks These tapes are especially used for electrical fine adjustment. Video Audio Hi-Fi Audio Track 10. Alignment Tape 525 Monoscope — 58µm VROATSV NTSC Color Bar — 58µm 46/58 VRONBZGS — 525 Monoscope µm...
  • Page 22 13VT-L200 MAINTENANCE CHECK ITEMS AND EXECUTION TIME Perform the maintenance with the regular intervals as follows so as to maintain the quality of machine. Maintained 500 1000 1500 2000 3000 Possible symptom Remarks Parts hrs. hrs. hrs. hrs. hrs. encountered Abnormal rotation or significant vi- Guide roller ass’y...
  • Page 23 13VT-L200 REMOVING AND INSTALLING THE CAS- Notes: SETTE HOUSING 1. When fitting the S/E sensor holder to the cassette controller frame L/R, take care. • Removal 2. Misengagement of teeth of casecon drive gear and 1. In the cassette eject mode, remove the cassette.
  • Page 24 13VT-L200 REEL DISK REPLACEMENT AND HEIGHT 4. Assemble the Sup main brake ass'y. CHECK Notes: • Removal 1. When installing the reel disk, take due care so that the 1. Remove the cassette housing control assembly. tension band ass'y is not deformed and grease does 2.
  • Page 25 13VT-L200 Note: Notes: Whenever replacing the reel disk, perform the height 1. Hold the torque gauge by hand so that it is not moved. checking and adjustment. 2. Do not keep the reel disk in lock state. Do not allow long-time measurement.
  • Page 26 13VT-L200 Notes: CHECKING AND ADJUSTMENT OF TAKE- 1. Hold the torque gauge by hand so that it is not moved. UP TORQUE IN VIDEO SEARCH REWIND 2. Do not keep the reel disk in lock state. Do not allow MODE long-time measurement.
  • Page 27 13VT-L200 CHECKING THE VIDEO SEARCH REWIND BACK TENSION • Remove the cassette housing control assembly. • After short-circuiting TP7701 and TP7702 pro- Tension gauge Pinch roller vided at the left on the main PWB, plug in the 900 - 1,200g power cord, then turn on the power.
  • Page 28 13VT-L200 2. Visually check to see if the right edge of the tension Tension pole adjuster adjusting range pole is within the 1.5 ± 0.25mm from the right edge of the Sup guide shaft. Tension pole adjuster Sup guide shaft Tension pole 0.25mm...
  • Page 29 13VT-L200 • Adjustment • Checking the brake torque at the take-up side 1. If the indication of torque cassette meter is lower than the setting, shift the tension spring engagement to the part A. Torque gauge 2. If the indication of torque cassette meter is higher than the setting, shift the tension spring engagement to the part B.
  • Page 30 13VT-L200 3. Align the left end of gear of A/C head arm with the REPLACEMENT OF A/C (Audio/Control) HEAD punched mark of chassis, tentatively tighten the screws 1. Remove the cassette housing control assembly. 1 and 2 so as to ensure smooth motion of A/C head 2.
  • Page 31 13VT-L200 A/C HEAD HEIGHT ROUGH ADJUSTMENT HEIGHT ADJUSTMENT OF REVERSE GUIDE • Setting 1. Adjust the height from the mechanism chassis to the reverse guide lower flange to 13.38mm, using the Azimuth screw reverse guide height adjustment jig, in tape loading state.
  • Page 32 13VT-L200 Notes: ADJUSTMENT OF TAPE DRIVE TRAIN 1. Previously set the tracking control in the center posi- 1. Tape run rough adjustment tion, and adjust the envelope waveform to maximum 1 Remove the cassette housing control assembly. with X value adjustment nut. Thereby the tape run 2 After shortcircuiting TP7701 and TP7702 provided rough adjustment is facilitated.
  • Page 33 13VT-L200 3. Tape run adjustment PB CHROMA 1 Connect the oscilloscope to PB CHROMA envelope Envelope output test point, set oscilloscope sync to EXT, trigger-input the PB CHROMA signal (head switch- ing pulse). 2 Rough adjustment of X value Tentatively fix A/C head arm screws 1 and 2 by...
  • Page 34 13VT-L200 REPLACEMENT OF DRUM D.D. MOTOR REPLACEMENT OF THE CAPSTAN D.D. 1. Set the eject mode. (DIRECT DRIVE) MOTOR 2. Withdraw the main power plug from the socket. • Remove the mechanism from the main PWB (refer to Page9 "DISASSEMBLY AND REASSEMBLY" Re- •...
  • Page 35 13VT-L200 REPLACING THE UPPER AND LOWER DRUM ASSEMBLING OF PHASE MATCHING ASSEMBLY MECHANISM COMPONENTS • Assemble the phase matching mechanism com- • Replacement (Perform in the numerical order) ponents in the following order. 1 Remove the motor as stated in Page 34 D.D. motor 1.
  • Page 36 13VT-L200 1Insert Reverse Guide Lever Ass’y Insert reverse guide lever ass'y 2 Insert pinch drive cam Align here. Turn the reverse guide lever assembly counterclockwise Fit the pinch drive cam so that the notch of pinch to the stopper. drive cam aligns with the dent of pinch drive lever assembly.
  • Page 37 13VT-L200 1. Make sure that the loading gear is at the point 1 as INSTALLING THE SHIFTER shown below. 2. Install, paying attention to 6 insertion points and 3 release points. Drum 3. For the phase matching at the insertion point 1, see Capstan the point 2 as shown below.
  • Page 38 13VT-L200 INSTALLING THE MASTER CAM (AT REAR REPLACEMENT OF LOADING MOTOR • Removal SIDE OF MECHANISM CHASSIS) 1. Make sure beforehand that the shifter is at the point as shown below. 2. Place the master cam in the position as shown below.
  • Page 39 13VT-L200 ASSEMBLY OF CASSETTE HOUSING 1. Drive Gear and R Drive angle ass’y MSPRT0381AJFJ Apply grease Apply grease Apply grease Figure 1-47. 2. Synchro Gear, Drive Gear L and Drive Gear R LANGF9592AJFW Top surface should be free from scratches or soil.

  • Page 40: Adjustment Of The Vcr Electrical Circuitry

    13VT-L200 ADJUSTMENT OF THE VCR ELECTRICAL CIRCUITRY Notes: » Before the adjustment: Electrical adjustments described here are often required after replacement of electronic components and mechanical parts such as video heads. Check that the mechanism and all electric components are in good working condition prior to the adjustments, otherwise adjustments can not be completed.
  • Page 41 13VT-L200 2 Pressing both the CH " (TR — ) and the "0" button SERVO CIRCUIT ADJUSTMENT transmits the test code. When the unit receives this ADJUSTMENT OF HEAD SWITCHING test code in the playback mode, the unit is turned into...
  • Page 42 13VT-L200 Note: 1 The data of this adjustment is memorized in the E ROM IC. 2 Pressing both the CH " (TR — ) button and the "0" button at the same time transmits the test code. When the unit receives this test code in the slow mode, the unit is turned into the adjustment mode for the SP or EP slow tracking preset and "T"...

  • Page 43: Troubleshooting

    ELECTRICAL TROUBLESHOOTING FLOW CHART NO.1-2 FLOW CHART NO.1-1 KEY-IN TROUBLESHOOTING VCR POWER TROUBLESHOOTING Key-in input for VCR is not received. The VCR is dead.(No power) Unplug the AC power cord. Is the key switch in good Check the switch contact. Replug it a few minutes later.
  • Page 44 LOADING MOTOR AND EJECT TROUBLESHOOTING FLOW CHART NO.1-4 CASSETTE CONTROL TROUBLESHOOTING FLOW CHART NO.1-3 A cassette tape fails to eject. A cassette tape is not taken in. Does the capstan motor start Fix or replace the cassette Is the cassette housing distored? See FLOW CHART NO.1-6.
  • Page 45 SYSTEM CONTROL TROUBLESHOOTING FLOW CHART NO.1-5 CAPSTAN MOTOR TROUBLESHOOTING FLOW CHART NO.1-6 No power. The capstan motor fails to run. Are serial clock pulse and TV Check the AT5V line. Is 5V at pin (8) of AC connector? data pulse applied to pins (67) and (66) of IC7701 from IC2001? Check between...
  • Page 46 TAKE-UP REEL PULSE GENERATOR TROUBLESHOOTING FLOW CHART NO.1-7 DRUM MOTOR TROUBLESHOOTING FLOW CHART NO.1-9 No reel sensor pulse appears. The drum motor fails to run. Check between the ME socket Insert the cassette, and Is the voltage more than about and pin (78) of IC7701, and put the unit in FF or REW 2.6V applied at pin (1) of ME...
  • Page 47 13VT-L200...
  • Page 48 CAPSTAN SERVO TROUBLESHOOTING FLOW CHART NO.1-11 Capstan servo does not function. Only PB mode inoperetive. Only REC mode inoperetive. Are REC and /or PB mode inoperative? Is there 16MHz oscillation at pins (38) and (39) of IC7701. Check X7701, C7705 and C7706.
  • Page 49 13VT-L200...
  • Page 50 13VT-L200...
  • Page 51 SOUND E-E MODE TROUBLESHOOTING SOUND RECORDING MODE TROUBLESHOOTING FLOW CHART NO.1-16 FLOW CHART NO.1-15 No E-E signal No record. Check circuits around the audio output Is there a signal at pin (87) or Is there "H" level at pin (70) of Check BIAS CTL (H) line.
  • Page 52 13VT-L200...
  • Page 53 13VT-L200 TROUBLESHOOTING OF TV SECTION...
  • Page 54 Circuit to be checked: FLOW CHART NO.2-3 FLOW CHART NO.2-4 NO PICTURE, NO SOUND NO VERTICAL SCAN 1. TUNER 2. PIF 3. Automatic gain control 4. 9V power source Does the noise level increase at max, Vertical freq check Abnormal Contrast, Brightness, and Sound Control? Noise increases but Picture noise...
  • Page 55 13VT-L200...

  • Page 56: Chassis Layout

    13VT-L200 CHASSIS LAYOUT PWB-B PWB-D PWB-C...
  • Page 57 13VT-L200 PWB-A...

  • Page 58: Block Diagram Of Tv Section

    13VT-L200 BLOCK DIAGRAM OF TV SECTION...
  • Page 59 13VT-L200...

  • Page 60: Block Diagram Of Vcr Section

    13VT-L200 BLOCK DIAGRAM OF VCR SECTION Ë OVERALL BLOCK DIAGRAM...
  • Page 61 13VT-L200...
  • Page 62 13VT-L200 BLOCK DIAGRAM OF VCR SECTION Ë SERVO PROCESS BLOCK DIAGRAM...
  • Page 63 13VT-L200...
  • Page 64 13VT-L200 BLOCK DIAGRAM OF VCR SECTION Ë SYSTEM CONTROL BLOCK DIAGRAM...
  • Page 65 13VT-L200 Ë SAFETY DEVICE BLOCK DIAGRAM...
  • Page 66 13VT-L200 BLOCK DIAGRAM OF VCR SECTION Ë VIDEO SIGNAL FLOW BLOCK DIAGRAM...
  • Page 67 13VT-L200...
  • Page 68 13VT-L200 BLOCK DIAGRAM OF VCR SECTION Ë AUDIO BLOCK DIAGRAM...
  • Page 69 13VT-L200...

  • Page 70: Overall Schematic Diagram

    13VT-L200 OVERALL SCHEMATIC DIAGRAM...
  • Page 71 13VT-L200...

  • Page 72: Description Of Schematic Diagram

    13VT-L200 DESCRIPTION OF SECTION SCHEMATIC DIAGRAM NOTE: WAVEFORM MEASUREMENT CONDI- 1. The unit of resistance "ohm" is omitted TIONS: (K:1000 ohms, M:1 Meg ohm). 1. Photographs taken on a standard gated color bar 2. All resistors are 1/8 watt, unless otherwise noted.
  • Page 73 13VT-L200 SCHEMATIC DIAGRAM : CRT Unit...
  • Page 74 13VT-L200 SCHEMATIC DIAGRAM : MAIN-1 Unit (TV Section)
  • Page 75 13VT-L200...
  • Page 76 13VT-L200 SCHEMATIC DIAGRAM : MAIN-2 Unit (TV Section)
  • Page 77 13VT-L200...
  • Page 78 13VT-L200 SCHEMATIC DIAGRAM : POWER Unit (TV Section)
  • Page 79 13VT-L200...
  • Page 80 13VT-L200 SCHEMATIC DIAGRAM : MAIN Unit (VCR-1 Section)
  • Page 81 13VT-L200...
  • Page 82 13VT-L200 SCHEMATIC DIAGRAM : MAIN Unit (VCR-2 Section)
  • Page 83 13VT-L200...

  • Page 84: Printed Wiring Board Assemblies

    13VT-L200 PRINTED WIRING BOARD ASSEMBLIES PWB-B: CRT Unit (Wiring Side) PWB-D: FRONT AV Unit (Wiring Side)
  • Page 85 13VT-L200 PWB-C: POWER Unit (Wiring Side)
  • Page 86 13VT-L200 PWB-A: MAIN Unit (Wiring Side)
  • Page 87 13VT-L200 PWB-A: MAIN Unit (Chip Parts Side)

  • Page 88: Replacement Parts List

    2. NO. DE REF 3. NO. DE PIECE 4. DESCRIPTION in USA: Contact your nearest SHARP Parts Distributor to order. For in CANADA: Contact SHARP Electronics of Canada Limited location of SHARP Parts Distributor, Please call Toll-Free; Phone (416) 890-2100...
  • Page 89 13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-A: DUNTK9489WEW7 D2001 RH-DX0475CEZZ Diode D2002 RH-DX0475CEZZ Diode MAIN Unit (Continued) D2003 VHD1SS119//-1 Diode Q2206 VS2SA1037KQ-1 2SA1037 D2060 RH-DX0475CEZZ Diode Q2207 VS2SA1037KQ-1 2SA1037 D2201 RH-DX0475CEZZ Diode Q2208 VS2SC2412KQ-1...
  • Page 90 13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-A: DUNTK9489WEW7 C355 VCEA0A1CW226M J C356 VCQYTA1HM104K Mylar MAIN Unit (Continued) C357 VCKYCY1CF474Z 0.47 Ceramic L6601 VPADK153J0000 Peaking C360 VCKYCY1HF103Z 0.01 Ceramic L6604 VP-DF221K0000 Peaking 220µH C361...
  • Page 91 13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-A: DUNTK9489WEW7 C3107 VCKYCY1HF103Z 0.01 Ceramic C3108 VCEAKA0JW107M 6.3V MAIN Unit (Continued) C3109 VCKYCY1CB104K Ceramic C2041 VCKYCY1CB104K Ceramic C3110 VCKYCY1HB222K 2200p 50V Ceramic C2060 VCKYCY1EB223K 0.022 25V...
  • Page 92 13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code RESISTORS PWB-A: DUNTK9489WEW7 (M.Ox. : Metal Oxide) MAIN Unit (Continued) VRN-MD2AL000J 0.1W Metal Film AA VRN-MD2AL000J 0.1W Metal Film AA C6630 VCQPSA2AA562J 5600p 100V VRN-MD2AL000J 0.1W Metal Film AA...
  • Page 93 13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-A: DUNTK9489WEW7 R456 VRN-MD2AL273J 0.1W Metal Film AA R466 VRN-VV3AB1R5J Metal Film AA MAIN Unit (Continued) R501 VRN-MD2AL101J 0.1W Metal Film AA R504 VRD-RA2BE471J 1/8W Carbon R207 VRN-MD2AL391J 0.1W Metal Film AA...
  • Page 94 13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-A: DUNTK9489WEW7 R3104 VRN-MD2AL561J 0.1W Metal Film AA R3107 VRN-MD2AL102J 1.0k 0.1W Metal Film AA MAIN Unit (Continued) R3108 VRN-MD2AL102J 1.0k 0.1W Metal Film AA R2061 VRN-MD2AL152J 1.5k...
  • Page 95 13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-A: DUNTK9489WEW7 R7738 VRN-MD2AL103J 0.1W Metal Film AA R7739 VRN-MD2AL562J 5.6k 0.1W Metal Film AA MAIN Unit (Continued) R7740 VRN-MD2AL103J 0.1W Metal Film AA R3308 VRN-MD2AL102J 1.0k 0.1W Metal Film AA...
  • Page 96 13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-A: DUNTK9489WEW7 P703 QPLGN0461CEZZ Plug 4-pin (YC) P2201 QPLGN0361CEZZ Plug, Test Point MAIN Unit (Continued) P2401 QPLGN0561CEZZ Plug, Test Point R7806 VRD-RA2BE103J 1/8W Carbon P3301 QPLGN0352GEZZ Plug, Test Point å...
  • Page 97 13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-C: DUNTK9490WEW4 CAPACITORS (EL. : Electrolytic) POWER Unit C702 VCKYPB2HE103P 0.01 500V Ceramic å INTEGRATED CIRCUITS C703 VCKYPB2HE103P 0.01 500V Ceramic å C705 RC-EZ0613CEZZ 200V EL. IC701...
  • Page 98 13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-C: DUNTK9490WEW4 PWB-B: DUNTK8606WEW4 CRT Unit POWER Unit (Continued) TRANSISTORS R744 VRD-RA2BE332J 3.3k 1/8W Carbon R745 VRD-RA2BE332J 3.3k 1/8W Carbon Q852 VS2SC2229O/1E 2SC2229 R746 VRD-RA2BE122J 1.2k 1/8W Carbon...
  • Page 99 13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code QCNW-0272AJZZ FFC for A/C Head MECHANISM CHASSIS QPWBF5469AJZZ A/C Head PWB QSOCN0605REN1 V Socket, 6-pin LBNDK1011AJZZ Tension Band Ass’y RHEDT0036AJZZ Full Erase Head LBOSZ1007AJZZ Tension Arm Boss RHEDU0088GEZZ A/C Head Ass’y...
  • Page 100 13VT-L200 MECHANISM CHASSIS PARTS Ref. No. Part No. Description Code Ref. No. Part No. Description Code...
  • Page 101 13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code MSLiF0076AJFW Slider CASSETTE HOUSING CONTROL MSPRD0151AJFJ Proof Lever (R) Spring MSPRD0166AJFJ Drive Gear (R) Spring CHLDX3081TEV2 Cassette Housing MSPRP0175AJFJ Cassette Spring LANGF9592AJFW Upper Plate MSPRT0381AJFJ Double Action Spring...
  • Page 102 13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code CABINET AND MECHANICAL PARTS CCABA2477WEV7 Front Cabinet Ass'y Not Available – Front Cabinet — GCOVA0084PESA Cover, R/C HBDGB0018PESA SHARP Badge HDECQ0129PESA Cassette Flap Door HDECQ0109PEKA Decoration Plate...
  • Page 103 13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code CABINET AND MECHANICAL PARTS...
  • Page 104 13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING PARTS SUPPLIED ACCESORIES (NOT REPLACEMENT ITEM) TGAN-0018PEZZ Guarantee Card SPAKC6388PEZZ – Packing Case — TCAUH0011PEZZ Caution Card SSAKA0031PEZZ – Polyethylene Bag — TiNS-6665PEZZ Operation Manual SPAKP0095PEZZ –...

  • Page 105: Packing Of The Set

    13VT-L200 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING OF THE SET SETTING POSITIONS OF THE KNOBS Power SW Polystyrene Bag Operation Manual Guarantee Card Batteries Rod Antenna Infrared R/C Unit Polyethylene Sack Buffer Material...
  • Page 106 Code Ref. No. Part No. Description Code COPYRIGHT © 1999 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

This manual is also suitable for:

13vt-l10013vt-l15013vt-cl10

Table of Contents