Makita SP6000 Instruction Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Saw
  5. SP6000
  6. Instruction manual

Makita SP6000 Instruction Manual

Plunge cut circular saw
Hide thumbs Also See for SP6000:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual
INSTRUCTION MANUAL
Plunge Cut Circular Saw
SP6000
007654
DOUBLE INSULATION
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
1

Advertisement

Table of Contents
loading

Related Manuals for Makita SP6000

Summary of Contents for Makita SP6000

  • Page 1 INSTRUCTION MANUAL Plunge Cut Circular Saw SP6000 007654 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

  • Page 2: Specifications

    Standard and can, therefore, also be used from sockets without earth wire. Makita Corporation responsible ENG102-2 manufacturer declare that the following Makita For European countries only machine(s): Noise Designation of Machine: Plunge Cut Circular Saw The typical A-weighted noise level determined according Model No./ Type: SP6000...

  • Page 3: General Power Tool Safety Warnings

    Europe who is: Keep cord away from heat, oil, sharp edges or Makita International Europe Ltd, moving parts. Damaged or entangled cords Michigan, Drive, Tongwell, increase the risk of electric shock.

  • Page 4: Specific Safety Rules

    power tool will do the job better and safer at the Do not reach underneath the workpiece or tool rate for which it was designed. base. The guard cannot protect you from the 18. Do not use the power tool if the switch does blade below the workpiece.
  • Page 5 toward the operator; − if the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and jump back toward the operator.
  • Page 6 illustrates the RIGHT way to cut off the end of a board, and Fig. 2 the WRONG way. If the workpiece is short or small, clamp it down. DO NOT TRY TO HOLD SHORT PIECES BY HAND! Fig. 1 000194 Never force the saw.

  • Page 7: Functional Description

    19. Do not stop the blades by lateral pressure on Quick stop button for 2 to 3 mm depth of cut the saw blade. when using guide rail (accessory) 20. Always use blades recommended in this 1. Quick stop manual. Do not use any abrasive wheels. button 21.
  • Page 8 Tilting to the right NOTE: Returning the blade to the right angle makes the 1. Positive stopper • shifting lever return to 0° by itself. Sighting 1. Base 2. Cutting line 007659 Turn the positive stopper so that the arrow on it points one of two positions (vertical for 22.5°, horizontal for 45°).

  • Page 9: Assembly

    6 and back to 1. Do not force it past 6 or 1, or at the front of the tool. the speed adjusting function may no longer work. Use only the Makita wrench to install or remove the • The speed adjusting dial is not for using low speed •...

  • Page 10: Operation

    When using with guide rail (accessory) 1. Adjusting screws 007673 When you wish to perform clean cutting operation, connect a Makita vacuum cleaner to your tool. Connect a hose of the vacuum cleaner to the dust port as shown 007685 in the figure.

  • Page 11: Maintenance

    When bevel cutting with the guide rail, slide the slide When using the tool with guide rail lever on the tool base so that the tool does not fall down Place the tool on the guide rail with the rear edge of tool on its side.

  • Page 12: Accessories

    Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. Saw blades • Guide rail • 007668 Rip fence (Guide rule) •...
  • Page 16 Makita Corporation Anjo, Aichi, Japan 884683F228...

Table of Contents