1. Manuals
  2. Brands
  3. Sony Manuals
  4. Monitor
  5. VAIO CPD-201VS
  6. Service manual

Sony TRINITRON VAIO CPD-201VS Service Manual

Trinitron multimedia computer display
Hide thumbs Also See for TRINITRON VAIO CPD-201VS:
Table of Contents

Advertisement

Quick Links

Download this manual

SERVICE MANUAL

Picture tube
0.25 mm aperture grille pitch,
17 inches measured diagonally
(16.0" viewable),
90-degree deflection,
AR coating
Viewable image size
Approx. 327 × 241 mm (w/h)
(12
16.0" viewing image
(measured diagonally)
Max. resolution
Horizontal: Max. 1280 dots
Vertical: Max. 1024 lines
640 × 480 at 85 Hz
VESA standards
800 × 600 at 85 Hz
1024 × 768 at 85 Hz
1280 × 1024 at 60 Hz
Deflection frequency
Horizontal: 30 to 70 kHz
Vertical: 50 to 120 Hz
Left, right: 3.0 W × 2
Speaker
50 Hz – 20 kHz
Microphones
Uni-directional, electret condenser
microphone
Microphones output
3.5 mm miniplug
Audio input
3.5 mm Stereo miniplug,
input impedance 47 kΩ,
input level 0.7 Vrms typical
TRINITRON
MICROFILM
SPECIFICATIONS
× 9
7
1
/
/
inches)
8
2
MULTIMEDIA COMPUTER DISPLAY
®
CPD-201VS
Canadian Model
Chassis No. SCC-L21A-A
V-3
Headphones output
Stereo minijack, 15 mW + 15 mW at
16 Ω
Subwoofer output
3.5 mm miniplug, volume variable
Controls
Front panel direct:
Audio volume/Contrast/Audio
mute/GPE (AUTO/off/mode 1/
mode 2)
OSD menu:
Brightness/Contrast/Picture size/
Picture zoom/Picture centering/
Sceen moiré/Color temperature
(5000K/6500K/9300K/11000K)/
Rotation/Pincushion/Pin balance/
Keystone/Key balance/Bass boost/
Manual Degauss/OSD position/
OSD language
AC input voltage/current
100 to 240 V, 50 – 60 Hz, 1.5 – 0.6 A
Power consumption
Max. 120 W
Approx. 415 × 451 × 423 mm
Dimensions
(w/h/d)
× 17
3
(16
/
8
Mass
Approx. 19.6 kg (43 lb 3 oz)
Design and specifications are subject to change without
notice.
US Model
CHASSIS
× 16
5
3
/
/
inches)
8
4

Advertisement

Table of Contents
loading

Related Manuals for Sony TRINITRON VAIO CPD-201VS

Summary of Contents for Sony TRINITRON VAIO CPD-201VS

  • Page 1: Service Manual

    CPD-201VS SERVICE MANUAL US Model Canadian Model Chassis No. SCC-L21A-A CHASSIS SPECIFICATIONS Picture tube 0.25 mm aperture grille pitch, Headphones output 17 inches measured diagonally Stereo minijack, 15 mW + 15 mW at 16 Ω (16.0” viewable), 90-degree deflection, Subwoofer output 3.5 mm miniplug, volume variable...

  • Page 2: Power Led

    Normal CPD-101VS: 110 W (max) Green Signaling (DPMS). By sensing the absence of the sync signal coming Operation CPD-201VS: 120 W (max) from the computer, it will reduce the power consumption as follows: Sleep 15 W (max) Approx. 3 sec.
  • Page 3 VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR Parts on Set SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS AP- PEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE- MENTS PUBLISHED BY SONY. CIRCUIT ADJUST- MENTS THAT ARE CRITICAL FOR SAFE OPERATION 0.15 µ...

  • Page 4: Table Of Contents

    CPD-201VS TABLE OF CONTENTS Section Title Page 1. GENERAL ..............1-1 2. DISASSEMBLY 2-1. Cabinet Removal ..........2-1 2-2. Service Position ........... 2-1 2-3. D Board Removal ..........2-2 2-4. U Board Removal ..........2-2 2-5. J Board Removal ..........2-3 2-6.

  • Page 5: General

    Congratulations on your purchase of a Sony Multimedia CPD-101VS/ Installation 201VS display! This display incorporates over 25 years of Sony experience with Trinitron • Prevent internal heat build-up by allowing adequate air circulation. display technology, ensuring excellent performance and outstanding Do not place the unit on surfaces (rugs, blankets, etc.) or near...

  • Page 6: Getting Started

    Although this display will sync to other platforms running at horizontal !¡ frequencies between 30 and 70 kHz, including Macintosh and Power Macintosh systems, a cable adapter is required. Please consult Sony Technical Support for advice on which adapter is !™ !∞ suitable for your needs.

  • Page 7: Using Your Display

    Beyond sound volume and picture contrast adjustment, most adjustments are made using the OSD menu system. Approx. 6 cm (2 inches) (CPD-201VS only) Using the OSD menu Damper wires Press the MENU button to display the MENU OSD. Approx. 6 cm...

  • Page 8: Adjusting The Sound Volume

    Summary of each item Adjusting the sound volume Press the . + or – button. MENU MENU The VOLUME/CONTRAST OSD appears. The horizontal and vertical frequencies for each input signal received COLOR CENTER SCREEN appear. VOLUME/CONTRAST BRIGHT EXIT ZOOM GEOM SIZE OPTION 65.

  • Page 9: Adjusting The Picture Size

    Press the ?// buttons to adjust the picture brightness. If you don’t touch any buttons, the OSD automatically disappears after 30 seconds. / for more brightness ? for less brightness Adjusting the picture size The adjustment data becomes the individual setting for each input signal received.

  • Page 10: Adjusting The Screen Moir

    Select the desired color temperature with the >/. buttons. Press the . button to select MOIRE ADJUST. 11000K for the brightest white SCREEN 9300K for TV white 6500K for video monitor white 5000K for printing paper white To exit the OSD MOIRE ADJUST Press the MENU button again.

  • Page 11: Available Gpe Modes

    For inquiries about “IntelliLight” and compatible software, check Sony’s web site (www.ita.sel.sony.com) or call Sony Technical Support (1-888- Resetting 4SONYPC).

  • Page 12: Troubleshooting

    Set the refresh rate on the computer to obtain the best possible picture by referring to your computer’s manual. • If the problem persists, call your authorized Sony dealer from a m If the GPE mode is set to AUTO, change it to OFF (page 32).

  • Page 13: Disassembly

    CPD-201VS SECTION 2 DISASSEMBLY 2-1. CABINET REMOVAL Cabinet Two claws Four screws (+BVTP 4 x 16) 2-2. SERVICE POSITION (1) D board (2) U board A block D board U board...

  • Page 14: D Board Removal

    CPD-201VS 2-3. D BOARD REMOVAL A block Screw (+BVTT 4 x 8) Five screws Cable stopper (+BVTP 3 x 12) Screw (+BVTP 3 x 12) Cable blacket CN904 CN512 CN601 CN607 D board 2-4. U BOARD REMOVAL CN5204 CN5200 CN5202...

  • Page 15: J Board Removal

    CPD-201VS 2-5. J BOARD REMOVAL Two screws (+BVTP 4 x 16) J board Screw (+BVTP 3 x 12) Seven screws (+BVTP 4 x 16) Stand base (Lower)

  • Page 16: Picture Tube Removal

    CPD-201VS 2-6. PICTURE TUBE REMOVAL Four screws (+BVTT 4 x 8) Two screws CN601 (+BVTP 4 x 16) A block CN314 CN303 CN304 Neck assy Stand assy Deflection yoke CN512 Four screws CN701 CN501 (Tapping screw 5) Picture tube shield...

  • Page 17: Harnes Location

    CPD-201VS 2-7. HARNESS LOCATION Microphone Picture tube Speaker Stand assy Demagnetic coil with screw (+BVTT4X8) CN6002 CN6003 CN6004 CN5204 CN5601 CN5606 D board CN5200 CN5202 CN902 CN503 CN5607 CN5605 J board CN903 CN904 CN607 U board DA board with screw...

  • Page 18: Safety Related Adjustment

    CPD-201VS SECTION 3 SAFETY RELATED ADJUSTMENT • HV Protector Circuit Check When replacing or repairing the shown below table, the following operational checks must be performed as a Confirm that the voltage between cathode of D517 on D safety precaution against X-rays emissions from the unit.

  • Page 19: Adjustments

    CPD-201VS SECTION 4 ADJUSTMENTS • Landing Rough Adjustment 5. Attach the sensor of the landing adjustment unit on the CRT 1. Enter the full white signal. (or the full black dots signal) surface. 2. Set the contrast to “CONT”=MAX. Purity magnet position 3.
  • Page 20 CPD-201VS Connect the communication cable of the computer to the connector located on the D board on the monitor. Run the service software and then follow the instruction. 1-690-391-21 A-1500-819-A 3-702-691-01 Interface Unit Connector Attachment IBM AT Computer To BUS CONNECTOR...

  • Page 21: Diagrams

    SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAMS SIGNAL-IN D-SUB15 (VIDEO) PIG-TAIL IC001 IC002 RGB OUT IC006 RGB PRE-AMP SPEAKER R-SP CN307 J001 BGND TO FBT FOCUS SPEAKER L-SP B IN B OUT B IN B OUT B IN B OUT BLUE GGND GREEN G IN...
  • Page 22 T505 HST IC501 PWM CONTROL IC902 T503 BUFF BUFF IC901 CPU BUFF D938 Q521 LED DRIVE MUTE LED KEY SCAN Q904 BUFF FUNCTION DF AMP OSC OUT V DF S-CAP Q505 Q504 D912 X901 CHANGE 24MHz Q512,515,516 IC900 LED RED OSC IN LED DRIVE H SYNC BUFF...

  • Page 23: Frame Schematic Diagram

    5-3. CIRCUIT BOARDS LOCATION Part replaced ( HV ADJ RV501 5-2. FRAME SCHEMATIC DIAGRAM AUDIO IN/ MIC OUT Part replaced ( PIG-TAIL HV Regulator D Board IC501, C553, C554 Circuit Check C555, C558, C561 R540, R564, R567 CN315 RV501, T501 (FBT) TEST SW TEST SW :S-MICRO...
  • Page 24 VIDEO — A BOARD (Conductor Side) — — A BOARD (Component Side) — • A BOARD SEMICONDUCTOR LOCATION Conductor Component Side Side IC001 B–2 B–3 IC002 A–3 A–2 IC003 A–2 A–4 IC004 B–4 B–1 IC005 B–4 IC006 B–2 B–3 IC008 A–1 IC009 B–1...

  • Page 25: Schematic Diagram Of A Board

    (1) Schematic Diagram of A Board IC002 LM2405T-C V901 RGB OUTPUT (VIDEO) J001 PICTURE TUBE 17FRFM IC001 R115 MM1382 TO D BOARD CN307 :RN-CP RGB PRE-MIX SG002 D-SUB 15 OSD MIX T501(HV) D301 C081 TO D BOARD (PIG TAIL) :S-MICRO 1SS226 R304 CN301...
  • Page 26 • D BOARD — D BOARD — POWER, DEFLECTION SEMICONDUCTOR LOCATION MICRO-CONTROLLER D515 – D516 – D517 – IC401 D518 – IC501 D520 – IC502 D521 – IC503 D522 – IC602 D523 – IC603 D524 – IC604 D525 – IC605 D526 –...

  • Page 27: Schematic Diagrams Of D Board

    (2) Schematic Diagram of D Board 5V-2 D GND KEY SCAN KEY SCAN R903 :CHIP 5V-2 IIC CLK C929 IIC DATA 0.001 B:CHIP R904 CN901 R940 5V-2 D905 D906 D901 :CHIP MA111 MA111 R908 R909 MA111 2.7k BRANDED :RN-CP :S-MICRO IC701 RN:CHIP RN:CHIP...

  • Page 28: Schematic Diagrams Of Aa, Da, J And U Boards

    (3) Schematic Diagrams of AA, DA, J and U Boards CN5204 :S-MICRO (HEADPHONE JACK) POWER SW R5222 +15V CN6001 A-GND :CHIP MUTE J6002 R1623 (AUDIO) C1610 R1608 TO U BOARD R6000 2.2k 470p IIC CLK D1605 JACK B:CP UDZ-TE-17-22B CN5605 R6001 IIC DATA HEAD-PHONE...
  • Page 29 (aa) (da) VIDEO (GPE) POWER CONTROL HEADPHONE JACK — AA BOARD (Conductor Side) — — AA BOARD (Component Side) — AA BOARD Terminal name of semiconductors in silk screen printed circuit ( Ref. Q801, Q803, Q805 Q806-Q810 D800-D805 : Refer to Terminal name of semiconductors in silk screen printed circuit (see page 5-7) —...

  • Page 30: Semiconductors

    5-5. SEMICONDUCTORS BA05T LA6500FA M62392FP PST600C-T TK75003D 1 TOP VIEW 24 pin SOP NJM4558M UPC1093J-1-T BA10324AF-E2 UPC4558G2 STK392-910A LA7840L SN74HC02ANS SN74HC02ANS-E20 XRA10324AF 1 TOP VIEW 8 pin SOP MARKING SIDE VIEW 1 TOP VIEW NJM78L09UA 14 pin SOP UPC5021-109 TA78L09F-TE12L ST72751N9B1/LAM LSC4514P2 CXA8070P...
  • Page 31 IRFI9630GS 2SA1175-HFE 2SJ175 D5S4M PC123F2 IRFI9630GS-LF 2SA1309A-QRSTA 2SJ175-02 PC123FY2 2SC2785-HFE 2SC3311A-QRSTA LETTER SIDE CATHODE ANODE EGP10D IRFU110 R2KS 2SK2194F08 IRFU110A RD6.2M-BT CATHODE 2SB798-DL 2SB798-DLDK ANODE EGP10GPKG23 SB340L-5009 DTZ10B MTZJ-T-77-18 IRLI530GLF33 DTZ33B RB441Q CATHODE MA111 RB441QT-77 RD12SB2 2SC2611 RD10ES-B2 RD5.6S-B RD12ES-B2 RD5.6SB3 RD18ES-B2 LETTER SIDE...

  • Page 32: Exploded Views

    CPD-201VS SECTION 6 EXPLODED VIEWS NOTE: • Items with no part number and no • Items marked " * " are not stocked since The components identified by shading description are not stocked because they they are seldom required for routine ¡...

  • Page 33: Stand Block

    CPD-201VS 6-2. STAND BLOCK 7-685-648-79 +BVTP 3X12 7-685-663-71 +BVTP 4X16 REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK * 4-058-388-01 COVER, CABLE 1-529-123-11 SPEAKER (5X9CM) * 4-058-385-01 STOPPER X-4035-821-1 BASE (LOWER) ASSY, STAND 4-066-421-01 COVER, BOTTOM * 4-061-996-01 CUSHION...

  • Page 34: Packing Materials

    CPD-201VS 6-3. PACKING MATERIALS The components identified by shading Les composants identifiés per un tramé ¡ ¡ and mark are critical for safety. et une marque sont critiques pour la Replace only with part number specified. sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.

  • Page 35: Electrical Parts List

    CPD-201VS CPD-201VS The components identified by shading Les composants identifiés per un tramé SECTION 7 ¡ ¡ and mark are critical for safety. et une marque sont critiques pour la (aa) Replace only with part number specified. sécurité. Ne les remplacer que par une ELECTRICAL PARTS LIST piéce portant le numéro spécifié.
  • Page 36 CPD-201VS The components identified by shading Les composants identifiés per un tramé ¡ ¡ et une marque sont critiques pour la and mark are critical for safety. (aa)(a) sécurité. Ne les remplacer que par une Replace only with part number specified.
  • Page 37 CPD-201VS The components identified by shading Les composants identifiés per un tramé ¡ ¡ and mark are critical for safety. et une marque sont critiques pour la Replace only with part number specified. sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
  • Page 38 CPD-201VS The components identified by shading Les composants identifiés per un tramé ¡ ¡ et une marque sont critiques pour la and mark are critical for safety. sécurité. Ne les remplacer que par une Replace only with part number specified.
  • Page 39 CPD-201VS The components identified by shading Les composants identifiés per un tramé ¡ ¡ and mark are critical for safety. et une marque sont critiques pour la (a)(d) Replace only with part number specified. sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
  • Page 40 CPD-201VS Les composants identifiés per un tramé The components identified by shading ¡ ¡ et une marque sont critiques pour la and mark are critical for safety. sécurité. Ne les remplacer que par une Replace only with part number specified.
  • Page 41 CPD-201VS The components identified by shading Les composants identifiés per un tramé ¡ ¡ and mark are critical for safety. et une marque sont critiques pour la Replace only with part number specified. sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
  • Page 42 CPD-201VS Les composants identifiés per un tramé The components identified by shading ¡ ¡ et une marque sont critiques pour la and mark are critical for safety. sécurité. Ne les remplacer que par une Replace only with part number specified.
  • Page 43 CPD-201VS The components identified by shading Les composants identifiés per un tramé ¡ ¡ and mark are critical for safety. et une marque sont critiques pour la Replace only with part number specified. sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
  • Page 44 CPD-201VS Les composants identifiés per un tramé The components identified by shading ¡ ¡ et une marque sont critiques pour la and mark are critical for safety. sécurité. Ne les remplacer que par une Replace only with part number specified.
  • Page 45 The components identified by [ in this CPD-201VS manual have been carefully factory- The components identified by shading Les composants identifiés per un tramé selected for each set in order to satisfy ¡ ¡ and mark are critical for safety.
  • Page 46 CPD-201VS The components identified by shading Les composants identifiés per un tramé ¡ ¡ et une marque sont critiques pour la and mark are critical for safety. (da)(u) sécurité. Ne les remplacer que par une Replace only with part number specified.
  • Page 47 CPD-201VS The components identified by shading Les composants identifiés per un tramé ¡ ¡ and mark are critical for safety. et une marque sont critiques pour la Replace only with part number specified. sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
  • Page 48 CPD-201VS The components identified by shading Les composants identifiés per un tramé ¡ ¡ et une marque sont critiques pour la and mark are critical for safety. (u)(j) sécurité. Ne les remplacer que par une Replace only with part number specified.

Table of Contents