Error Messages - Husqvarna FS5000 D Operator's Manual

Error messages

Message on the
Fault Code
display
U100087 I/O Controller
U100088 I/O Controller
P060745 IOC MPU
P060742 IOC MPU
Blade depth
C1E0111
sensor signal
Blade depth
C1E0112
sensor signal
C1D0115 Starter
C1D0111 Starter
Power supply
C1D0711
external device
C1D0815 AUX1
C1D0811 AUX1
C1D0215 AUX2
C1D0211 AUX2
TROUBLESHOOTING
DTC description Indication on the machine
Engine can not be started. No
No CAN
machine function can be
communication
controlled.
Engine can not be started. No
Software download
machine function can be
failed
controlled.
Engine can not be started. No
Program memory
machine function can be
failure
controlled.
Engine can not be started. No
General memory
machine function can be
failure
controlled.
Blade depth can not be
Circuit short to
displayed. Blade depth stop
ground
can not be used.
Blade depth can not be
Circuit short to
displayed. Blade depth stop
battery
can not be used.
Engine starter can not be
Circuit short to
controlled. Cutting can not
battery or open
continue.
Circuit short to
Engine can not be started.
ground
Circuit short to
Cutting can not continue.
ground
Circuit short to AUX1 can not be controlled by
battery or open the HMI.
Circuit short to AUX1 can not be controlled by
ground the HMI.
Circuit short to AUX2 can not be controlled by
battery or open the HMI.
Circuit short to AUX2 can not be controlled by
ground the HMI.
Possible action
Check damage to HMI connector and chassis harness. If
found, repair and restart system, reset fault code.
If problem still exists, contact your service agent for further
information.
Contact your service agent.
Contact your service agent for further information.
Contact your service agent for further information.
Disconnect sensor and reset fault code. If fault code no longer
exists check sensor and sensor harness.
Check damage to HMI connectors and harness to sensors. If
found, repair and restart system, reset fault codes.
Contact your service agent for further information.
Disconnect sensor and reset fault code. If fault code no longer
exists check sensor and sensor harness.
Check damage to HMI connectors and harness to sensors. If
found, repair and restart system, reset fault codes.
Contact your service agent for further information.
Check damage to HMI and ECU connector and harness. If
found, repair and restart system, reset fault code.
It problem still exists, contact your service agent for further
information.
Check damage to HMI and ECU connector and harness. If
found, repair and restart system, reset fault code.
If problem still exists, contact your service agent for further
information.
Check cables to:
Blade depth sensor and sensor itself
E-track position sensor and sensor itself
Neutral start switch and switch itself
Fuel level sensor and sensor itself
Lower/raise switch and switch itself
Water safety switch and switch itself
Change HMI
Check AUX1 relay in relay/fuse box.
Check damage to HMI connector, harness to relay/fuse box
and relay/fuse box connector. If found, repair and restart
system, reset fault code.
If problem still exists, contact your service agent for further
information.
Check AUX1 relay in relay/fuse box.
Check damage to HMI connector, harness to relay/fuse box
and relay/fuse box connector. If found, repair and restart
system, reset fault code.
If problem still exists, contact your service agent for further
information.
Check AUX2 relay in relay/fuse box.
Check damage to HMI connector, harness to relay/fuse box
and relay/fuse box connector. If found, repair and restart
system, reset fault code.
If problem still exists, contact your service agent for further
information.
Check AUX2 relay in relay/fuse box.
Check damage to HMI connector, harness to relay/fuse box
and relay/fuse box connector. If found, repair and restart
system, reset fault code.
If problem still exists, contact your service agent for further
information.
– 57
English