Table of Contents
Related Manuals for HIKVISION UD04285B
Summary of Contents for HIKVISION UD04285B
- Page 1 Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Hikvision DS-2CD4A26FWD-IZHS/P o cerca il tuo prodotto tra le migliori offerte di Videosorveglianza Network Bullet Camera Quick Start Guide UD04285B...
- Page 2 Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
- Page 3 LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.
- Page 4 Network Bullet Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules.
- Page 5 Network Bullet Camera·Quick Start Guide 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.
- Page 6 Network Bullet Camera·Quick Start Guide Warnings Follow these Cautions Follow these safeguards to prevent precautions to prevent serious injury or death. potential injury or material damage. Warnings ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. ●...
- Page 7 Network Bullet Camera·Quick Start Guide ● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. Cautions ● Make sure the power supply voltage is correct before using the camera.
- Page 8 Network Bullet Camera·Quick Start Guide ● While in delivery, the camera shall be packed in its original packing, or packing of the same texture. ● Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment shall be replaced regularly according to their average enduring time.
-
Page 9: Table Of Contents
Network Bullet Camera·Quick Start Guide Table of Contents 1 Appearance Description ..............9 1.1 Overview ................. 9 1.2 Micro SD Card Installation ..........10 2 Installation ..................12 Ceiling Mounting ............13 Wall Mounting with a Junction Box ....... 17 Wall Mounting with a Gang Box ........ -
Page 10: Appearance Description
Network Bullet Camera·Quick Start Guide 1 Appearance Description Overview The overview of the network bullet camera is shown below. Figure 1-1 Overview Table 1-1 Description Description Photoresistor Lens Sun Shield 3-axis Bracket Network Cable Interface... -
Page 11: Micro Sd Card Installation
Network Bullet Camera·Quick Start Guide Description Power Cable Interface Alarm Cable Interface Video Cable Interface Audio Out Audio In Reset Button Micro SD Card Slot Serial Port The standard power supply is 12V DC or 24V AC, please make sure ... - Page 12 Network Bullet Camera·Quick Start Guide Slot Cover Figure 1-2 Remove Card Cover 2. Insert the SD card into the SD card slot. Micro SD Card Figure 1-3 Insert the Card 3. (Optional) Push the inserted micro SD card inside to remove the micro SD card.
-
Page 13: Installation
Network Bullet Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. -
Page 14: Ceiling Mounting
Network Bullet Camera·Quick Start Guide Ceiling Mounting Steps: 1. Drill the screw holes and the cable hole in the ceiling according to the supplied drill template. Ceiling Mounting 1:Screw Hole for 2:Screw Hole for Bracket Mounting Base Figure 2-1 Drill Template 2. - Page 15 Network Bullet Camera·Quick Start Guide Please insert the expansion screws first if the camera is mounted to the cement ceiling. And you can use the self-tapping screws directly if camera is mounted to the wooden ceiling. Figure 2-2 Install the Camera 3.
- Page 16 Network Bullet Camera·Quick Start Guide 0° ~ 360° 0° ~ 360° 0° ~ 100° Figure 2-3 Adjust the Surveillance Angle Figure 2-4 Supplied Wrench 4. (Optional) Install the water-proof jacket for network interface. It is recommended to adopt the water-proof jacket (supplied) for the network interface when the camera is installed outdoor.
- Page 17 Network Bullet Camera·Quick Start Guide 3). Insert the water-proof ring into the main body of the water-proof jacket, to increase the sealing ability of the components. 4). Wire the plug and network cables up. 5). Fix the O-ring to the network interface of the camera, and then connect the network cables.
-
Page 18: Wall Mounting With A Junction Box
Network Bullet Camera·Quick Start Guide Wall Mounting with a Junction Box Steps: 1. Drill the screw hole and cable hole according to the supplied drill template (shown as Figure 2-1). 2. Align the screw holes of the junction box to the drill template, and fix the junction box to the wall with screws. -
Page 19: Wall Mounting With A Gang Box
Network Bullet Camera·Quick Start Guide Wall Mounting with a Gang Box An adapter plate should be purchased separately if you mount the camera to a gang box. Steps: 1. Install the adapter plate to the gang box. 2. Route the cables. 3. -
Page 20: Setting The Network Camera Over The Lan
Network Bullet Camera·Quick Start Guide 3 Setting the Network Camera over the Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. -
Page 21: Activating The Camera
Network Bullet Camera·Quick Start Guide Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. -
Page 22: Activation Via Sadp Software
Network Bullet Camera·Quick Start Guide Figure 3-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. - Page 23 Network Bullet Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2.
-
Page 24: Modifying The Ip Address
Network Bullet Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. - Page 25 Network Bullet Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Figure 3-5 Modify the IP Address...
- Page 26 Network Bullet Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.
-
Page 27: Accessing Via Web Browser
Network Bullet Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps:... - Page 28 Network Bullet Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.
-
Page 29: Operating Via Hik-Connect App
Network Bullet Camera·Quick Start Guide 5 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so Note: Hik-Connect service is not supported by certain camera models. Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using... -
Page 30: Enable Hik-Connect Service Via Web Browser
Network Bullet Camera·Quick Start Guide Figure 5-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 5.1.2 Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service. - Page 31 Network Bullet Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Figure 5-2 Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4.
-
Page 32: Hik-Connect Setup
Network Bullet Camera·Quick Start Guide Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google Play 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. Adding Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before... - Page 33 Network Bullet Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number.
-
Page 34: Initializing The Memory Card
Network Bullet Camera·Quick Start Guide Initializing the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.