Honeywell VisionPRO IAQ Product Data page 15

ISU
Parameter Installer Setup
Number Name
345 Dual Fuel Heat
Pump Control
346 Dual Fuel Heat
Pump Upstage to
Furnace Timer
350 Heat Pump
Balance Point
(also compressor
lockout)
Temperature
360 Heat Pump
Auxiliary Heat
Lockout
Temperature
365 Discharge Temp
Sensor
366 Zoning High
Temperature
Limit
367 Zoning Low
Temperature
Limit
368 Staging
Discharge
Temperature
High Limit
369 Staging
Discharge
Temperature
Low Limit
370 Indoor Humidity
Sensor
372 Indoor
Humidification
Control
Table 3. Installer Setup Menu. (Continued)
Settings
(Factory Defaults Shown in Bold)
0 Balance point only
1 Balance point plus 2° droop
2 Balance point/auxiliary heat lockout plus 2° droop.
0 Disabled
30 30 minutes
45 45 minutes
60 60 minutes
75 75 minutes
0 No heat pump compressor lockout
5 -15 5°F -15.0°C
10 -12 10°F -12.0°C
15 -9.5 15°F -9.5°C
20 -6.5 20°F -6.5°C
25 -4 25°F -4.0°C
30 -1 30°F -1.0°C
35 1.5 35°F 1.5°C
40 4.5 40°F 4.5°C
45 7 45°F 7.0°C
50 10 50°F 10.0°C
55 13 55°F 13.0°C
60 15.5 60°F 15.5°C
(Show 1/2 degree C)
0 No heat pump auxiliary lockout
5 -15 5°F -15.0°C
10 -12 10°F -12.0°C
15 -9.5 15°F -9.5°C
20 -6.5 20°F -6.5°C
25 -4 25°F -4.0°C
30 -1 30°F -1.0°C
35 1.5 35°F 1.5°C
40 4.5 40°F 4.5°C
45 7 45°F 7.0°C
50 10 50°F 10.0°C
55 13 55°F 13.0°C
60 15.5 60°F 15.5°C
65 18.5 65°F 18.5°C
(Show 1/2 degree C)
0 None
1 Remote
E Auto Discover
160 160°F (71°C)
0 Disabled
110–170 110°F to 170°F (43.5°C to 76.5°C)
40 160°F (71°C)
0 Disabled
35-50 35°F to 50°F (1.5°C to 10°C)
110 110°F (43.5°C)
0 Disabled
80-130 80°F to 130°F (26.5°C to 54.5°C)
55 55°F (13°C)
0 Disabled
50-60 50°F to 60°F (10°C to 15.5°C)
0 Disabled
1 Internal—sensor in thermostat
2 Remote
E Auto Discovered
0 Off
1 Humidify with no Frost Protection
3 Humidify with Frost Protection
E Auto Discover
VISIONPRO
See Dual Fuel Heat Pump control on page 22.
See Dual Fuel Heat Pump control on page 22.
Only shown for heat pump applications with an
outdoor temperature sensor present.
Only shown for heat pump applications with an
outdoor temperature sensor present.
Only Shown if ISU110 = 1 (Master Zone Controller)
and Discharge Temperature Sensor is available.
Only Shown if ISU110 = 1 (Master Zone Controller)
and Discharge Temperature Sensor is available.
Only Shown if ISU110 = 1 (Master Zone Controller)
and ISU174 = 2 or more. Must have Discharge
Temperature Sensor present.
Only Shown if ISU110 = 1 (Master Zone Controller)
and ISU176 = 2. Must have Discharge Temperature
Sensor present.
If there is a remote sensor installed and the setting is
either auto discover or "remote" the internal thermostat
humidity sensor is disabled. If set to "internal" the
internal thermostat sensor is presented on the screen.
If set to "disabled" the internal sensor and any remote
sensors are disabled, there will be no humidity
displayed and will have no humidification/
dehumidification control.
Shown only if ISU370 = 1, 2 or E.
15
®
IAQ TOTAL HOME COMFORT SYSTEM
Notes
68-0287—1