Disassembly/Assembly Procedures Of Deck Mechanism - AEG VCR 4500 Service Manual

DISASSEMBLY/ASSEMBLY PROCEDURES
Before following the procedures described below, be sure to remove the deck assembly from the cabinet. (Refer to
CABINET DISASSEMBLY INSTRUCTIONS.)
All the following procedures, including those for adjustment and replacement of parts, should be done in Eject
mode; see the positions of [44] and [45] in Fig. DM1H on page 2-4-3. When reassembling, follow the steps in
reverse order.
STEP START-
/LOC. ING
No. No.
[1] [1] Guide Holder A
Cassette Holder
[2] [1]
Assembly
[3] [2] Slider (SP)
[4] [2] Slider (TU)
[5] [4] Lock Lever
[6] [2] Cassette Plate
[7] [7] Cylinder Assembly
Loading Motor
[8] [8]
Assembly
[9] [9] ACE Head Assembly
Tape Guide Arm
[10] [2]
Assembly
[11] [10] C Door Opener
[12] [11] Pinch Arm (B)
Pinch Arm (A)
[13] [12]
Assembly
[14] [14] FE Head
[15] [15] Prism
[16] [2] Slider Shaft
[17] [16] C Drive Lever (SP)
[18] [16] C Drive Lever (TU)
[19] [19] Capstan Motor
[20] Clutch Assembly (HI)
[20]
[21] [20] Center Gear
*
F Brake Assembly (HI)
[22]
[22]
[23] [22] Worm Holder
[24] [22] Pulley Assembly (HI)
Mode Gear (LM)
[25]
[25]
[26] Mode Lever (HI)
[20],[25]
[22],[23],
[27] Cam Gear (A) (HI)
[26]
TR Gear C
[28] [26]
[29] [28] TR Gear Spring
[30] [29] TR Gear A/B
FF Arm (HI)
[31] [31]
[32] [26] Idler Assembly (HI)
OF DECK MECHANISM
PART
Fig. No.
T DM3H
T DM4H
T DM5H
T DM5H
T DM5H
T DM5H
T DM1H, DM6H
T DM1H, DM7H
T DM1H, DM7H
T DM1H, DM8H-1
T DM1H, DM8H-1
DM1H, DM8H-1,
T
DM8H-2
DM1H, DM8H-1,
T
DM8H-2
T DM1H, DM9H
T DM1H, DM9H
T DM10H
T DM10H
T DM10H
B DM2H, DM11H
B DM2H, DM12H
B DM12H
B DM2H, DM12H
B DM2H, DM13H-1 (S-9), *(L-7), *(L-8)
B DM2H, DM13H-1
B DM2H, DM13H-1 (C-2)
DM2H, DM13H-1,
B
DM13H-2
DM2H, DM13H-1,
B
DM13H-2
B DM2H, DM13H-1 (C-5)
B DM13H-1
B DM13H-1
B DM1H, DM14H
B DM1H, DM14H
REMOVAL
REMOVE/*UNHOOK/
UNLOCK/RELEASE/
UNPLUG/DESOLDER
2(S-1)
(S-1A), *(L-1)
*(L-2)
*(L-3), *(P-1)
Desolder, 3(S-2)
Desolder, LDG Belt,
2(S-3)
(S-4)
*(P-2)
(S-4A), *(L-4)
*(P-3)
(S-5)
(S-6)
*(L-5)
(S-7), *(P-4)
3(S-8), Cap Belt
(C-1)
*(L-6)
(C-3)
(C-4)
*(L-9)
2-4-1
INSTALLATION
ADJUSTMENT
CONDITION
(+)Refer to Alignment
Sec.Page 2-5-1
U29PHSDA