Related Manuals for Yamaha CDR400tx
Summary of Contents for Yamaha CDR400tx
- Page 1 CDR400tx User Guide Guide de I’utilisateur Bedienungsanleitung P O W R E A W R IT O N / D IS C - 4 0 0 C D R da bl R ec or V O L...
- Page 2 If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Systems Technology, Inc. 100 Century Center Court, San Jose, CA95112, U.S.A.
- Page 3 Laser Diode Properties CAUTION Material : GaAlAs Use of controls or adjustments or performance of Wavelength : 780-790 nm procedures other than those specified herein may Emission Duration : Continuous result in hazardous radiation exposure. Laser Output Power : Less than 44.6 W* his output is value measured at a distance 200mm from the objective lens ADVARSEL...
-
Page 4: Important Precautions
Important Precautions Please read the following precautions before operat- ing CDR400tx. • Do not remove the CDR400tx’s top cover. This device uses semiconductor laser. Refer all servic- ing to qualified personnel. • Do not attempt to touch the inside of the CDR400tx. - Page 5 Do not block the CDR400tx ventilation slots. Install CDR400tx with at least 10 cm of free space all-around. • Make sure the CDR400tx power cord is not located in a position where it is likely to be walked on or pinched by other equipment.
- Page 6 Important Precautions Operating Precautions • Do not subject CDR400tx to impact or shock when in use. This may impair recording or playback. • Do not place heavy objects on CDR400tx. • Avoid moving CDR400tx from cold to warm places, and avoid sudden room temperature rises, as condensation that could cause CDR400tx to malfunction may occur.
- Page 7 If a disc tray accumulates dust, DO NOT USE IT FOR DISC RECORDING. Always use a clean, dust-free tray for disc recording. If CDR400tx is vibrated while recording, the recording may fail. To avoid such failures observe the following practices: •...
-
Page 8: Table Of Contents
About Discs ..............5 Chapter 2 - Touring Around CDR400tx ....6 Front Panel..............6 Rear Panel..............7 Chapter 3 - Installing the Yamaha CDR400tx Drive ..................8 CDR400tx drive settings ..........8 Cable Connection ............9 Chapter 4 - Operation ............ 10 Loading a Disc............. -
Page 9: Introduction
Introduction Introduction Thank you for purchasing a Yamaha CDR400tx drive. Please read this manual before using the drive in order to make the best use of the superior CDR400tx functions. After reading, please retain this man- ual for future reference. -
Page 10: Cdr400Tx Features
The CDR400tx can both record and read seven different formats: CD- ROM, CD-ROM XA, CD-I, CD-DA, CD-Bridge (multisession), CD- Extra, and Video CD. The CDR400tx is also equipped with an analog audio output terminal (headphones) for CD-DA. SCSI 2 for High-Volume, High-Speed Data Transfer The CDR400tx features SCSI 2, the second generation SCSI interface for connecting computers and peripheral devices. -
Page 11: Orange Book Compatible Recording
Track at Once In this mode, data can be recorded to disc one track at a time. Discs recorded in this mode can be played in the CDR400tx anytime. They cannot, however, be played in other CD players until the final record- ing is made. -
Page 12: Chapter 1 - System Configuration
CD-ROM. SCSI card and software Yamaha CDR400tx is a “SCSI” device. You will need to install a SCSI card and some mastering (writing) software in your host com- puter to connect the CDR400tx. -
Page 13: About Discs
Chapter 1 - System Configuration About Discs CD-R Discs On the CDR400tx, you can use conventional CD-R discs that con- form to the Recordable Compact Disc Systems Part II (Orange Book). Yamaha recommends the following Yamaha CD-R discs: > CDM12Y63 ( 120mm, 63 minutes) >... -
Page 14: Chapter 2 - Touring Around Cdr400Tx
This control adjusts the volume level of the headphone output. Rotat- ing the control clockwise will increase the volume level. 4 ON/DISC LED This indicator lights up in orange when the CDR400tx is powered on, and lights up in green when the CDR400tx contains a disc. 5 READ/WRITE LED This indicator lights up in green when data is being read, and flashes... -
Page 15: Rear Panel
1 AC IN Connect the included power cable here. 2 CDR ID Use this switch to set a unique SCSI ID number for the CDR400tx. 3 TERMINATOR This switch is used to set termination. Refer to the terminator setting section for details. -
Page 16: Chapter 3 - Installing The Yamaha Cdr400Tx Drive
Terminator setting The terminator setting indicates whether or not this device is the last connected SCSI device. Terminator ON — Use this setting if the CDR400tx is the last device in the TERMINATOR SCSI daisy-chain. Terminator OFF — Use this setting if devices other than the CDR400tx are... -
Page 17: Cable Connection
(1) or (2), and connect the other end of the SCSI cable to the host computer. The CDR400tx is not supplied with a SCSI cable. You will need to obtain one that will fit the drive and the host computer connectors. -
Page 18: Chapter 4 - Operation
Chapter 4 - Operation Chapter 4 - Operation Loading a Disc 1. Press the eject button to open the tray. 2. Carefully place the disc, label-side up, on the disc tray. 3. Press the disc tray softly or press the eject button again to close the disc tray. -
Page 19: Ejecting The Disc
Press the eject button to eject the disc. Note: You cannot eject the disc if the SCSI command prohibits the eject operation while the CDR400tx is reading data. Caution: Be sure to remove the disc after it is completely ejected. (Trying to remove the disc before it is completely ejected may cause the drive to malfunction.) -
Page 20: Troubleshooting
Troubleshooting Troubleshooting If CDR400tx is not performing as expected, look up the symptoms in the following table, then see what to do. Symptoms What to Do The power to the CDR400tx is off • Check the AC power cable connection. -
Page 21: Appendix
Appendix Specifications Interface SCSI 2 Data Capacity 1.2m/sec: 666MB 1.4m/sec: 540MB Record/Read Speed 1xS (real-time), 2xS, 4xS, 6xS (read) Data Transfer Rate 6xS: 900KB/sec 4xS: 600KB/sec 2xS: 300KB/sec 1xS: 150KB/sec Burst Transfer Rate 4.2MB/sec (record asynchronous) 3.4MB/sec (read asynchronous) Buffer Size 2MB (500 sectors) Access Speed 250ms... -
Page 22: Front Panel Indicator Key
Appendix Front Panel Indicator Key on: green flashing: green — off on: orange flashing: orange ON/DISC Read/Write Status — — Reset — Ready (no disc) Inserting disc — — Ejecting disc — Ready (disc inserted) Seeking Preparing to write Writing Writing (test mode) Playback —... - Page 23 YAMAHA CORPORATION Electronic Systems Division VY75090-1...