FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH. FOR USE IN THE U.S. AND CANADA. SUITABLE FOR INSTALLATION IN MOBILE HOMES IF THIS HARMAN STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. FOR YOUR SAFETY, FOLLOW INSTALLATION DIRECTIONS.
Manufactured by: Harman Stove Co. 352 Mountain House Road Halifax, PA 17032 CONTENTS INTRODUCTION ...3 INSTALLATION ...4 Clearances...4 Venting ...5 Requirements for Terminating the Venting ...6 Assembly ...7 Connecting to a Gas Supply ...9 Connecting the Cordset ... 10 Connecting the Thermostat ... 10 Air Shutter Adjustment ...
The Harman Clarity Direct Vent 929DV Gas Heater is a listed gas-fired direct vent room heater tested by Inchcape Testing/Warnock Hersey to ANSI standard Z21.88-2002, CSA 2.33-M02, and CAN/CGA-2.17-M91. The installation of the Clarity Direct Vent Gas Heater must conform with local codes, or in the absence of local codes, with National Fuel Gas Code, ANSI Z223.1 —...
IMPORTANT NOTICE Due to high temperatures, the Clarity Direct Vent Gas Heater should be located out of traffic and away from furniture and draperies. Children and adults should be alerted to the haz- ards of high surface temperatures and should stay away to avoid burns or clothing ignition.
Use Only Approved Venting The Clarity Direct Vent Gas Heater has been tested and is listed for installation with Simpson Duravent GS vent- ing components. The Simpson Duravent GS warranty will be voided, and serious fire, health, or other safety hazards may result from any of the following actions: •...
Requirements for Terminating the Venting WARNING: Venting terminals must not be recessed into a wall or siding. In addition, the following must be observed: A. The clearance above grade, or a veranda, porch, deck or balcony must be a minimum of 12" (30 cm). B.
To keep the levers in the disengaged position, tighten the wing nuts. Lift the glass front slightly and remove it from the stove. Set the glass aside in a safe place where it will not be damaged.
Page 8
Install the Branch Orient the branch with the forked end toward the left rear of the stove and slip it over the two locator pins, one on top of the back log and the other on the top of the center log.
Making The Connection The gas inlet is located at the bottom right rear of the stove. The inlet fitting is a 1/ 2" female flare flexible pipe. A separate gas shut-off valve an d a 1/8" N.P.T.
CONNECTING THE HEATER TO CORDSET Connecting the Cordset The Clarity Direct Vent Gas Heater must be installed in accordance with local codes or, in the absence of local codes, with the most recent edition of the National Electrical Code ANSI/NFPA 70, or the current Canadian Electrical Code C22.1.
Two of them are accessible through the side access port on the right side of the stove. The third is accessible from the front when the control door is open. The screws may become hot to the touch after prolonged operation.
HOW TO LIGHT THE FIRE 1. STOP! Read the safety information on the left side of the panel on page 13. 2. If using the optional thermostat, set thermostat to the lowest setting. 3. Turn off electric power to the appliance. 4.
Handling dam- age to the ceramic logs is not covered by warranty. DO NOT HANDLE LOGS WHILE THEY ARE HOT. ALLOW PLENTY OF TIME FOR THE STOVE TO COOL COMPLETELY BEFORE HANLDING. Remove the Branch Detach the branch from the two locator pins and re- move it.
Page 15
WIRING DIAGRAM Clarity Direct Vent Wiring Diagram The Clarity Direct Vent gas heater, when installed, must be electrically grounded in accordance with current local codes or, in the absence of local codes, with the current edition of National Electrical Code, ANSI/NFPA 70 in the United States or the current Canadian Electrical Code CSA 22.1 in Canada.
The following replacement parts for your Harman Clarity Direct Vent are available from your Harman dealer. Part No. Part 1-89-08250 DVG weldment 3-44-08294 Starting Collar Gasket 3-40-3849239 Starting Collar 1/2” gas inlet flex 3-40-08286 3-40-08235 Rear log 3-40-08236 Front log 3-40-08237 Top log 3-40-08401...
9 in. (230 mm) 9 in. (230 mm) 4 in. (100 mm) 3 in. (75 mm) 18 in. (460 mm) 14 in. (460 mm) Manufactured by: Harman Stove Company 352 Mountain House Road Halifax, PA 17032 PROPANE 40,000 28,000 56/71/53 10.0/2.49...
To keep the levers in the disengaged position, tighten the wing nuts. Lift the glass front slightly and remove it from the stove. 3. Remove the Log Set See the directions on page 14.
De-rating for High Altitude For U.S. installations, the Clarity Direct Vent is approved for elevations up to 2000 feet using the factory-installed burner injectors. At elevations above 2000 feet, U.S. codes require a decrease in the input rating by changing the burner injectors to a smaller size.
MERCHANTABILITY, OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. No employee, agent, dealer, or other person is authorized to give any warranty on behalf of Harman Stove Company. This warranty does not apply if the product has been altered in any way after leaving the factory. Harman Stove Company and its agents assume no liability for “resultant damages of any kind”...