Table of Contents
Advertisement
Quick Links
34˚ FRAMING NAILER KIT
MODEL H5571
INSTRUCTION MANUAL
COPYRIGHT © SEPTEMBER, 2003 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN
ONLINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE
AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS
PRODUCT IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF
THE MACHINE, THIS MANUAL MAY NOT EXACTLY DEPICT YOUR MACHINE. CONTACT CUS-
TOMER SERVICE IF YOU HAVE ANY QUESTIONS ABOUT DIFFERENCES.
PREVIOUS VERSIONS ARE NOT AVAILABLE ONLINE.
Advertisement
Table of Contents
Related Manuals for Grizzly H5571
Summary of Contents for Grizzly H5571
-
Page 1: Instruction Manual
INSTRUCTION MANUAL COPYRIGHT © SEPTEMBER, 2003 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN TAIWAN ONLINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. -
Page 2: Safety Instructions For Pneumatic Tools
Keep work area well lighted. H5571 34˚ Framing Nailer Kit SAFETY Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. - Page 3 WHILE UNSUPERVISED. 23. IF YOU ARE UNSURE OF THE INTENDED OPERATION, STOP USING THE TOOL. Seek formal training or research books or maga- zines that specialize in pneumatic tools. RECOMMENDED Consult DAMAGED PARTS. ALLOW UNTRAINED H5571 34˚ Framing Nailer Kit...
- Page 4 DO NOT USE A CHECK VALVE OR ANY OTHER FITTING that allows air to remain in the tool. H5571 34˚ Framing Nailer Kit Operating this nailer can propel objects into the air, causing immedi- ate eye damage. To protect yourself,...
- Page 5 At 8 lbs., this model is very light for its size. We are pleased to provide this manual with the Model H5571. It was written to encourage safety considerations and guide you through general operating pro- cedures and maintenance. This manual represents our effort to produce the best documentation possible.
-
Page 6: Compressed Air System
Compressed Air System The Model H5571 is designed to be oper- ated at 85-115 psi. DO NOT exceed the maximum operating pressure! Before you use your new nailer, regulate the air pressure on your air compressor to barely over the minimum psi for your nail- er. -
Page 7: Operation
Oiling Nailer Special oil has been included with your new Grizzly nailer to help maintain its use- ful life. Place one drop of oil in the nailer air inlet (as shown in Figure 1) before every use. Wipe off any excess oil near the nail- er exhaust to avoid dust build-up. -
Page 8: Operating Nailer
If the nail either went too far or not far enough, adjust the depth. H5571 34˚ Framing Nailer Kit Adjusting Depth The nose of the gun houses a depth adjustment knob for setting the depth that the nailer drives nails into the workpiece. -
Page 9: Clearing Jammed Nails
Single/Bump Fire Mode The Model H5571 is equipped with a sin- gle/bump fire trigger. To select single or bump fire operation: Disconnect the air supply from the nailer! Locate the single/bump fire selector on the trigger. See Figure 5. To select Single Fire mode, push in the selector and rotate it down. - Page 10 Ignoring this warning may lead to serious personal injury or even death! H5571 34˚ Framing Nailer Kit Always disconnect air from nailer whenever servicing! During mainte- nance, a nailer connected to air may...
-
Page 11: Replacing Pistons/O-Rings
Replacing Pistons/O-Rings If you use your nailer day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or pis- ton shaft becomes worn out. Always disconnect air from nailer... - Page 12 H5571 PART BREAKDOWN H5571 34˚ Framing Nailer Kit...
- Page 13 LOCK WASHER 8MM PW05M FLAT WASHER 4MM PSB18M CAP SCREW M4-.7 X 8 PH5571091 SPRING PH5571092 SET BALL PH5571095 IDLE ROLLER PSB118M BTN HD CAP SCR M5-.8 X 20 PH5571097 MAGAZINE BLOCK 100 PH5571100 ROLLER H5571 34˚ Framing Nailer Kit...
-
Page 14: Troubleshooting
Tool runs slowly or has a loss of power. Fasteners frequently jam the nailer. Nailer does not fire. H5571 34˚ Framing Nailer Kit CAUSE 1. O-rings in trigger valve housing are damaged. 1. Loose screws in housing. 2. Damaged O-ring. -
Page 15: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. -
Page 16: Warranty Card
14. Do you think your purchase represents good value? 15. Would you recommend Grizzly to a friend? 16. Would you allow us to use your name as a refer- ence for Grizzly customers in your area? Note: We never use names more than three times. 17.Comments:________________________________... - Page 17 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT NAIL Place Stamp Here...