Table of Contents
Advertisement
18 GAUGE BRAD NAILER
MODEL G6045/G6046/G6047
INSTRUCTION MANUAL
Model G6046
Nailer With Case
COPYRIGHT © OCTOBER, 2001 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
PRINTED IN TAIWAN
Model G6047
Model G6045 not shown
Advertisement
Table of Contents
Related Manuals for Grizzly G6045
Summary of Contents for Grizzly G6045
-
Page 1: Instruction Manual
COPYRIGHT © OCTOBER, 2001 BY GRIZZLY INDUSTRIAL, INC. 1821 VALENCIA ST., BELLINGHAM, WA 98227 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN TAIWAN Model G6047... -
Page 2: Safety Instructions For Power Tools
For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbols is described below. - Page 3 100ft 19. CHECK DAMAGED PARTS. Before 20. NEVER LEAVE TOOL RUNNING 21. NEVER 22. IF YOU ARE UNSURE OF THE G6045/G6046/G6047 18 Gauge Brad Nailer Keep tools sharp and clean for best and safest performance. Follow instructions lubricating changing accessories.
- Page 4 DO NOT USE A CHECK VALVE OR OTHER FITTING ALLOWS AIR TO REMAIN IN THE TOOL. G6045/G6046/G6047 18 Gauge Brad Nailer Operating this nailer can propel objects into the air, causing immedi- ate eye damage. To protect yourself, always Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment.
- Page 5 INTRODUCTION Commentary We are proud to offer the Grizzly Model G6045/G6046/G6047 18 Gauge Brad Nailer. This model is part of a growing Grizzly family of fine power tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer...
-
Page 6: Compressed Air System
Compressed Air System The Models G6045 & G6046 are designed to be operated at 60-100 psi. The Model G6047 is designed to be operated at 70- 110 psi. Do not exceed the maximum operating pressure for your model. Before using your new nailer, install the included ⁄... -
Page 7: Operation
Figure 3.) Figure 3. Example of brad nail deflection. G6045/G6046/G6047 18 Gauge Brad Nailer... -
Page 8: Oiling Nailer
As mentioned before, the best option is to install a filter/lubricator/regulator unit such as the Grizzly Model H2333 in your air line. Figure 4. Lubricating nailer via air inlet. G6045/G6046/G6047 18 Gauge Brad Nailer... -
Page 9: Clearing Jammed Nails
Close the magazine cover so it latch- To clear a jammed nail from the discharge area with the Model G6045/G6047: Disconnect the nailer from the air supply! Remove all of the brad nails from the magazine. -
Page 10: Replacing Pistons/O-Rings
Replacing Pistons/O-Rings If you use your nailer day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or pis- ton shaft becomes worn out. To replace a... - Page 11 G6045 PART BREAKDOWN G6045/G6046/G6047 18 Gauge Brad Nailer...
- Page 12 O-RING P6045038 TRGR VALVE GUIDE P6045039 SPRING 40A P6045040A TRIGGER ASSEMBLY 41A P6045041A LATCH * These items are not shown in the illustration. G6045/G6046/G6047 18 Gauge Brad Nailer PART # DESCRIPTION P6045042 CAP SCREW P6045043 LOCK WASHER P6045044 DRIVER GUIDE CVR...
- Page 13 G6046 PART BREAKDOWN G6045/G6046/G6047 18 Gauge Brad Nailer...
- Page 14 O-RING P6046037 O-RING P6046038 TRGR VALVE GUIDE P6046039 SPRING 40A P6046040A TRIGGER ASSEMBLY * These items are not shown in the illustration. G6045/G6046/G6047 18 Gauge Brad Nailer PART # DESCRIPTION P6045041 P6046042 CAP SCREW P6046043 LOCK WASHER P6046044 DRIVER GUIDE CVR...
- Page 15 G6047 PART BREAKDOWN G6045/G6046/G6047 18 Gauge Brad Nailer...
- Page 16 P6047038 TRGR VALVE GUIDE P6047039 SPRING 40A P6047040A TRIGGER ASSEMBLY 41A P6047041 LATCH * These items are not shown in the illustration. G6045/G6046/G6047 18 Gauge Brad Nailer PART # DESCRIPTION P6047042 CAP SCREW P6047043 LOCK WASHER P6047044 DRIVER GUIDE CVR...
-
Page 17: Troubleshooting
1. Nail is jammed in maga- zine or discharge area. 2. Piston shaft is damaged. 3. Air pressure too low. G6045/G6046/G6047 18 Gauge Brad Nailer ACTION 1. O-rings must be replaced & operation of safety yoke must be checked. -
Page 18: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. -
Page 19: Warranty Card
14. Do you think your purchase represents good value? 15. Would you recommend Grizzly to a friend? 16. Would you allow us to use your name as a refer- ence for Grizzly customers in your area? Note: We never use names more than three times. 17.Comments:________________________________... - Page 20 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...