Page 2
WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. •...
TABLE OF CONTENTS INTRODUCTION ...1 COMMENTARY ...1 III. SAFETY RULES ...2 UNPACKING ...3 AIR ...3 A. AIR PRESSURE ...3 B. AIR QUALITY...3 PRE-USE CHECKS ...4 A. CLEANING...4 B. OILING ...4 VII. OPERATIONS ...4 A. LOADING FASTENERS ...4 B. UNLOADING FASTENERS ...5 C.
But owing to Grizzly’s poli- " long. cy of continuous improvement, changes to the Model G3690 may occur at any time with no obligation on the part of Grizzly. Should you receive a manual update, please insert it into the manual and keep it for reference.
13. DO NOT carry gun with your finger on the trigger. Gun will fire if safety nose is acci- dentally depressed. - 2 - Grizzly Imports, Inc. G3690 14. DO NOT place your free hand or feet near the gun tip to support the work. If...
Keep air hoses as clean as possible inter- nally. Inspect nipples and couplers for any dirt and moisture. Blow out prior to connecting the gun. V. AIR clean operational. G3690 Grizzly Imports, Inc. - 3 -...
B. OILING Keep the gun oiled. Use special pneumatic tool oil to keep internal parts well lubricated. This tool oil is available through the Grizzly Catalog (G2820). If your air supply is not pre-lubricated, you must add 2 drops of oil directly into the air nozzle at the rear of the gun each time the magazine is loaded.
This tool is very simple to use and effectively speeds production. However, ease of use and routine production work may invite accidents. Please practice safe work habits at all times and always wear ANSI approved safety equip- ment. G3690 Grizzly Imports, Inc. - 5 -...
(120 p.s.i. for the gun). Disconnect the air hose from the gun when finished. Unload fasteners. See Section VII.B. - 6 - Grizzly Imports, Inc. G3690 E. ROUTINE USE To operate the nail gun under routine con- ditions, always wear safety glasses and: Line up the gun nose with the area on the workpiece you intend to fasten.
Page 10
Exhausted air will cause any dust near the operating gun to become airborne; use a res- pirator if using the gun in a dusty environment. G3690 Grizzly Imports, Inc. - 7 -...
If waiting for parts or repair, the tool must be tagged “do not use” and removed from the work area. - 8 - Grizzly Imports, Inc. G3690 Inspect air hoses and fittings for wear and tear and replace if necessary.
If the driver tip is worn, you may be able to recondition the tip by filing it square again. In any event, you must remove the damaged driver from the gun. See Section IX.B. G3690 Grizzly Imports, Inc. - 9 -...
NOTE: Before putting the gun back together, read through Section IX.C. - 10 - Grizzly Imports, Inc. G3690 C. O-RINGS AND RE-ASSEMBLY Since the gun is disassembled, inspect the condition of the visible O-rings. If the O-rings show signs of wear and tear, they should be replaced.
This could cause leaks anywhere in the gun. Again, if you have a problem and would like assistance, please call the appropriate service department. They will be glad to assist you. G3690 Grizzly Imports, Inc. - 11 -...
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom. We shall in no event be liable for death,...
Grizzly also carries an air hose, an in-line regulator/filter/water-separator/lubricator, quick con- nect couplers, and a complete line of fasteners for this gun. Please refer to a current Grizzly cat- alog for price and ordering information.
P3690440 RUBBER FOOT PLW01M LOCK WASHER 5mm P3690442 SPRING P3690443 LOCK HANDLE UNIT PRP43M ROLL PIN 3 x 22 PRP44M ROLL PIN 3 x 10 PRP02M ROLL PIN 3 x 16 G3690 Grizzly Imports, Inc. - 15 - " NPT...