Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Advertisement
Table of Contents
Related Manuals for Grizzly G1067Z
Summary of Contents for Grizzly G1067Z
- Page 1 WOOD LATHE MODEL G1067Z INSTRUCTION MANUAL COPYRIGHT © 1996 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. REVISED FEBRUARY, 1999. PRINTED IN U.S.A.
-
Page 2: Table Of Contents
LATHE SAFETY RULES ...15 TEST RUN ...16 TOOL REST ...16 SPINDLE TURNING ...17 OUTBOARD TURNING ...18 INDEXING...18 MAINTENANCE...19 GENERAL...19 LUBRICATION ...19 BED...19 CLOSURE ...20 MACHINE DATA...21 PART BREAKDOWN ...22-23 PART LISTS ...24 WARRANTY AND RETURNS ...27 G1067Z Wood Lathe Table Of Contents PAGE... -
Page 3: Introduction
The time you invest before you begin to use your Model G1067Z will be time well spent. DO NOT operate this machine until you are completely familiar with the contents of this manual. -
Page 4: Safety Rules For All Tools
11. NEVER STAND ON, OR LEAN ON THE TOOL. Doing so could cause injury. G1067Z Wood Lathe 12. USE SAFETY GLASSES AND EAR PRO- TECTION. Also use a DUST MASK if the operation is dusty. -
Page 5: Unpacking
Unpacking The Model G1067Z Wood Lathe is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for delivery, please call Customer Service immediately for advice. Save the containers and all packing materials for possible inspection by the carrier or its agent. -
Page 6: Clean Up
Clean up The bed and other unpainted parts of the Model G1067Z are coated with a waxy oil that protects them from corrosion during shipment. Remove the protective coating with mineral spirits and paper towels. DO NOT use gasoline or other petroleum based solvents because of their extremely low flash points. -
Page 7: Circuit Requirements
Circuit Requirements The motor supplied with the G1067Z is wired for 110V only. Under normal use, the motor draws approximately 10 amps @ 110V. We recommend using a 15 amp cir- cuit breaker or a 20 amp fuse for 110V operation. -
Page 8: Assembly
SECTION 2: ASSEMBLY Pre-assembly Assembly of the G1067Z is straightforward. We have organized the assembly process into steps. Please follow them in sequence. Tools Required: Only a few common tools are needed to assemble this machine. Specifically, a 6" adjustable wrench, 12mm open end wrench, regular and Phillips ®... - Page 9 With an assistant, set the lathe bed assem- bly on the stand, orienting the front of the headstock with the switch opening in the stand leg. Bolt the lathe bed to the stand using the eight and Hex Nuts supplied and tighten down.
-
Page 10: Installing The Switch
Installing the Switch Do not plug cord in until you are ready to test run the lathe. See Test Run section for instructions before initial run. Locate the on/off switch and the front and rear covers which will be held in place by two Phillips ®... -
Page 11: Tool Rest
Tool Rest The tool rest is equipped with a cam-action clamping system to secure it to the lathe bed. When the lever is thrown, a locking plate lifts up and secures the tool rest to the bed. To install the... -
Page 12: Spur Center
Spur Center The G1067Z is supplied with a #2 Morse taper spur center for use when spindle turning. The spur center is used in conjunction with the tail- stock live center. Install the spur center by insert- ing into the hole in the inboard spindle. Figure 9. -
Page 13: Adjustments
SECTION 3: ADJUSTMENTS Headstock The Model G1067Z headstock can be swiveled 180˚ as well as positioned anywhere along the bed. To position the headstock along the bed: Loosen the quick release lever by pushing it down. Figure 12. Move the headstock to the desired position and re-engage the quick release lever. -
Page 14: Headstock
Serious personal injury may occur. Figure 15. Headstock set at 90˚. Figure 16. Headstock set at 180˚. G1067Z Wood Lathe Tailstock The tailstock is equipped with a cam-action clamping system to secure it to the lathe bed. -
Page 15: Live Center
''. Insert the live cen- ter back into the tailstock barrel. (1) The tailstock barrel lock handle must always be locked down while the lathe is in use. Figure 18. The workpiece can be thrown from the lathe if this step is not observed. -
Page 16: Operations
— particularly when testing new tools or machinery. Do not allow visitors into your workshop when testing or operating equipment. Serious personal injury may occur. The Model G1067Z is capable of causing seri- ous personal injury if used in a reckless man- ner. -
Page 17: Test Run
Ensure that the lathe chisel is fully supported by the tool rest. Support the lathe chisel on the tool rest with one hand, while controlling the chisel with the other hand. Figure 20. For outboard turning, it may be desirable to use a free standing tool rest. -
Page 18: Spindle Turning
For dense wood, drill a hole for the center and score lines with a saw blade for the spurs. G1067Z Wood Lathe Once the spur center is firmly attached to the workpiece, insert the spur center (with the attached workpiece) into the headstock spin- dle. -
Page 19: Outboard Turning
17'' and a maximum thickness of 2''. Figure 21 depicts the lathe setup for turning a bowl using the tool rest extension supplied. Figure 22 depicts the lathe setup for turning a bowl using a free standing tool rest (not supplied). -
Page 20: Maintenance
G1067Z Wood Lathe Lubrication The G1067Z Lathe is equipped with a split pulley system which allows the speed of the lathe to be changed while its running. To assure the smooth operation of this pulley system, we recommend the main spindle and motor spindle be greased occasionally. -
Page 21: Closure
Washington location using the address in the Introduction. The specifications, drawings, and photographs illustrated in this manual represent the Model G1067Z as supplied when the manual was prepared. However, due to Grizzly’s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly. -
Page 22: Machine Data
Customer Service #: (570) 326-3806 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 GRIZZLY MODEL G1067Z HEAVY-DUTY WOOD LATHE Design Type ...Floor Model Overall Dimensions: Including Stand ...45 Swing Over Bed...14" Swing Over Gap ...17" Distance Between Centers ...40"... -
Page 23: Part Breakdown
-22-... - Page 24 -23-...
-
Page 25: Part Lists
⁄ POWER CORD * ON/OFF SWITCH SAFETY LABEL * STOP BAR V-BELT M-22 SET SCREW ⁄ ''-18 x ⁄ LOCKING STUD KNOB TOOL REST EXTENSION HEX BOLT ⁄ ''-18 x 1'' LOCK WASHER ⁄ KNOCK OUT BAR G1067Z Wood Lathe... -
Page 26: Warranty Card
Do you think your purchase represents good value? ___Yes Would you recommend Grizzly Imports to a friend? ___Yes Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than three times. ___Yes Comments:_________________________________________________... - Page 27 FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...
-
Page 28: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.