The hood is supplied as an extractor unit and can also be used with a filtering function by fitting activated carbon filters (special accessory). You will need original AEG activated carbon filters for this function (see Special Accessories). The air is forced out through a hose fitted to the...
You will need an original AEG KF2000 activated carbon filter for the filtering function. (See Special Accessories). Unplug the unit or disconnect it from the power supply Fig.
Electrical connections Electrical connections Electrical connections Electrical connections Electrical connections Safety warnings for electrician Safety warnings for electrician Safety warnings for electrician Safety warnings for electrician Safety warnings for electrician Check that the power supply voltage shown on the rating plate corresponds to the mains supply before proceeding to make any electrical connections.
T T T T T echnic Details echnic Details echnic Details echnic Details echnic Details Dimensions: Height x Width x Depht (in cm) 84-134 x 89,8 x 51 Weight: Net: Gross: 22,3 kg 29 kg Maximum absorbed power: 240 W Motor absorption: 1 x 215 W Lighting:...
Installation Installation Installation Installation Installation Safety warnings for kitchen unit installer Safety warnings for kitchen unit installer Safety warnings for kitchen unit installer Safety warnings for kitchen unit installer Safety warnings for kitchen unit installer When used as an extractor unit, the hood must be fitted with a 150mm diameter hose.
Page 8
Hoods can only be used safely with appliances connected to a chimney if the room and/or flat (air/environment combination) is ventilated from outside using a suitable ventilation hole approximately 500-600 cm large to avoid the possibility of a depression being created during operation of the hood.
Installation Installation Installation Installation Installation Rest the template correctly against the wall. The lower corner of the template corresponds to the lower corner of Fig. 3. Fig. 3. the extractor hood. Fig. 3. Fig. 3. Fig. 3. A cross is marked on the template to indicate the centre.
Page 10
From inside the hood, mark the final points at which the hood has to be fixed to the wall. Fig. 5. Fig. 5. Fig. 5. Fig. 5. Fig. 5. (to reach these points it will be necessary to remove activated carbon filter frame until the filter itself is Fig.
Page 11
Remove the telescopic chimney support M M M M M by unscrewing the side screws R R R R R (one on each side - these screws must be kept). Fig. 6 Fig. 6 Fig. 6 Fig. 6. Fig. 6 Remove the air pipe L L L L L from the telescopic chimney support M M M M M ;...
Page 12
Select the hood operating mode Extractor operation Extractor operation Extractor operation Extractor operation Extractor operation Fix the 150 mm diameter ABS pipe to the hood outlet and ensure that the other end discharges into the open air. The hood is supplied with a reducer for 120 mm diameter pipes.
Safety warnings for user Safety warnings for user Safety warnings for user Safety warnings for user Safety warnings for user Never leave a cooking hob or ring on without a pot or pan on top of it, to avoid the possibility of excess heat damaging the unit.
V V V V V iew of the hood iew of the hood iew of the hood iew of the hood iew of the hood 1. 1. 1. 1. 1. Control panel 2. 2. 2. 2. 2. Lighting units 3. 3. 3. 3. 3. Metal grease filters 4.
Setting the fan speed Setting the fan speed Setting the fan speed Setting the fan speed Setting the fan speed Fig. 9 Fig. 9 Fig. 9 Fig. 9 Fig. 9 Press the ( ) button (F) to select the fan speed from 1 to 9, keeping it pressed until the speed you want, e.g.
Intensive speed P Intensive speed P Intensive speed P Intensive speed P Intensive speed P Fig. 10 Fig. 10 Fig. 10 Fig. 10 Fig. 10 To select the intensive speed (P), press the increase speed button ( ) (F) until the letter P (high speed) is shown on Fig.
Switching of Switching of f the fan (Figures 10 - 11) Switching of f the fan (Figures 10 - 11) f the fan (Figures 10 - 11) f the fan (Figures 10 - 11) Switching of Switching of f the fan (Figures 10 - 11) Press the key (B) to switch off the fan at any speed including P.
A decisive parameter for the elimination of cooking odours is what is known as the “residence time” of the air sucked into the hood in the activated carbon filter. The correct “residence time” can only be obtained using original AEG activated carbon filters (see Special Accessories).
Display warning on saturation of activated Display warning on saturation of activated Display warning on saturation of activated Display warning on saturation of activated Display warning on saturation of activated carbon filter carbon filter carbon filter carbon filter carbon filter After 120 operating hours, the letter (C) (activated carbon filter) will flash on and off on the display (D) in alternation with the fan speed setting.
Page 20
Proceed as follows to remove and change my activated carbon filter: Switch of the fan motor by pressing the button. Take the precaution of removing my cartridge fuses from their fuse holders or tripping my automatic circuit breaker to ensure the fan motor cannot be switched on accidentally.
Display warning on saturation of metal grease Display warning on saturation of metal grease Display warning on saturation of metal grease Display warning on saturation of metal grease Display warning on saturation of metal grease filter filter filter filter filter After 30 operating hours the letter (F- grease filters) will flash on and off on the display (D) in alternation with the Fig.
Page 22
Hand washing Hand washing Hand washing Hand washing Hand washing Soak grease filters for about one hour in hot water with a grease-loosening cleaner, then rinse off thoroughly with hot water. Repeat the process if necessary. Refit the grease filters when it are dry. Dishwasher machine Dishwasher machine Dishwasher machine...
W W W W W arning arning arning arning arning Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations.
Cleaning Cleaning Cleaning Cleaning Cleaning Warning: always disconnect the hood from the mains power supply before cleaning it. Never insert pointed objects in the motor’s protective grid. Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders.