Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AEG 65402 G
Summary of Contents for AEG 65402 G
- Page 1 65402 G 65852 G Instruction Booklet Gas Hob...
-
Page 3: Table Of Contents
Contents Important Safety Information ..................4 Instructions for the User ....................6 Description of the Hob ......................6 Operation ............................7 Maintenance and Cleaning ....................10 The Hob Top ..........................10 The Pan Supports ........................10 The Burners ..........................11 The Ignition Electrode ...................... -
Page 4: Important Safety Information
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation This appliance must be installed and serviced by a competent person as stated in the Gas Safety (Installation and Use) Regulations Current Editions and the IEE Wiring Regulations. - Page 5 by opening a window or increasing the extractor speed. Do not use this hob if it is in contact with water. Do not operate the hob with wet hands. Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance.
-
Page 6: Instructions For The User
Description of the Hob Mod. 65852 G Mod. 65402 G 1. Hob Top 2. Semi-rapid Burner 3. Triple Crown Burner 4. Rapid Burner 5. Auxiliary Burner 6. Control knob for front left burner (semi-rapid) 7. Control knob for back left burner (semi-rapid) 8. -
Page 7: Operation
Operation Hob burners control knobs The symbols on the knobs mean that : there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support. To light a burner: turn the relevant knob anticlockwise to maximum position (... - Page 8 Do not keep the control knob pressed for more than 15 seconds. If the burner does not light even after 15 seconds, release the control knob, turn it the “off” position ( ) and wait for at least one minute before trying to light the burner again.
- Page 9 As soon as a liquid starts boiling, turn down the flame so that it will barely keep the liquid simmering. Use only pans or pots with flat bottom. If you use a saucepan which is smaller than the recommended size, the flame will spread beyond the bottom of the vessel, causing the handle to overheat.
-
Page 10: Maintenance And Cleaning
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. This appliance cannot be cleaned with steam or with a steam cleaning machine. -
Page 11: The Burners
The Burners The burner caps and crowns can be removed for cleaning. Wash the burners caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. -
Page 12: Something Not Working
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM SOLUTION There is no spark when lighting Check that the unit is plugged in the gas. and the electrical supply is switched on. -
Page 13: Instructions For The Installer
Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width: 594 mm Depth: 510 mm CUT OUT DIMENSIONS Width: 560 mm Depth: 480 mm SUPPLY CONNECTIONS Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V 50 Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. - Page 14 BURNER RAPID SEMI-RAPID A U X I L I A R Y TRIPLECROWN TYPE OF GAS POSITION M A X MIN M A X MIN M A X MIN M A X NOMINAL THERMAL POWER 3. 0 0. 7 5 2.
-
Page 15: Important Safety Requirements
Important Safety Requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. -
Page 16: Installation
Installation IMPORTANT This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a registered competent person. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. -
Page 17: Gas Connection
Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. -
Page 18: Location
Location The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but not in a bathroom, shower room or garage. Ensure that there is a minimum distance of 55 mm between the rear cut out edge and the wall. -
Page 19: Fitting The Hob Into The Worktop
Fitting the Hob into the Worktop Carry out the building in of the hob as follows: 1) place the seals supplied with the hob on the front edge of the cut out. Then, place them at 11 mm from the side edges and at 10 mm from the rear edge, as shown in the diagram, taking care that the seals meet without overlapping. -
Page 20: Building In
Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2. -
Page 21: Electrical Connections
Electrical Connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230 V 50 Hz AC electrical supply. -
Page 22: Permanent Connection
The switch must not break the yellow and green earth cable at any point. Ensure that the hob supply cord does not come into contact with surfaces with temperatures higher than 50 deg. C. Wiring Diagram Mod. 65852 G Mod. 65402 G... -
Page 23: Fault Finding
Fault Finding Preliminary Electrical Systems Check Blue Brown Green Yellow START Isolate appliance Blue and carry out: Green Brown A: Earth Continuity Yellow check. Carry out: Y E S Carry out: D: Resistance to C: Polarity check. Earth check. Has inlet fuse blown? Electricity supply should now be Y E S... - Page 24 A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 W (Ohm), check all earth wires for continuity and all contacts clean and tight.
-
Page 25: Ignition System / Gas Ignition
Ignition System / Gas Ignition Y E S Check gas supply at Ignitor does not spark burner Check plug top fuse and Light burner manually replace if necessary Check by pass simmer Check polarity and earth adjusted continuity of supply point Check fitting Check position of the Check earth continuity... -
Page 26: Commissioning
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. -
Page 27: Conversion From Natural Gas To Liquid Gas
Conversion from Natural Gas to Liquid Gas IMPORTANT The replacement/conversion from natural gas to LPG should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted. -
Page 28: Guarantee/Customer Service
Guarantee/Customer Service Standard guarantee conditions We, AEG-Electrolux, undertake that if within 12 months of the date of the pur- chase this AEG-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or... -
Page 29: Service And Spare Parts
Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning 0870 5 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your postcode area. -
Page 30: European Guarantee
European Guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications: •... - Page 32 www.aeg-electrolux.co.uk...