Summary of Contents for HIKVISION Color Zoom Camera
Page 1
Color Zoom Camera USER’S MANUAL Version 2.0.0...
Page 2
Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable to DS-2CZ232P/N, DS-2CM232P/N, DS-2CZ252P/N, DS-2CM252P/N, DS-2CZ282P, and DS-CZ292P series color zoom cameras. This manual may contain several technically incorrect places or printing errors, and the content is subject to change without notice.
Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may cause if any of the warnings is neglected. Cautions: Injury or equipment damage may cause if any of the cautions is neglected.
Page 4
Cautions: Make sure the power supply voltage is correct before using the camera. Do not drop the camera or subject it to physical shock. Do not touch CCD (Charge Coupled Device) modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently.
Table of Contents C H A P T E R 1 ..........................1 INTRODUCTION ..........................1 1.1 P ..........................2 RODUCT EATURES ......................2 1.2 S LATE OF THE AMERA ......................3 1.3 R LATE OF THE AMERA ..................3 1.4 C HIEF NTRODUCTION ABOUT...
Page 6
......................20 4.2 OSD M ONFIGURATION 4.2.1 Menu Structure ........................20 4.2.2 Shutter ........................... 22 4.2.3 Auto Gain Control ........................22 4.2.4 White Balance ........................23 4.2.5 Auto Focus ..........................23 4.2.6 Day / Night ..........................24 4.2.7 Motion Detection ........................25 4.2.8 Special Fuctions ........................
1.1 Product Features DS-2CZ232P(DS-2CM232P),DS-2CZ252P (DS-2CM252P) series are high performance cameras which adopt 1/4" SONY Interline Transfer Super HAD CCD and advanced print circuit board design technology, and possess of high resolution, lower distortion, and lower noise features. They are extremely suitable for surveillance system and image process system.
Figure 1.2 DS-252P side plate 1.3 Rear Plate of the Camera Figure 1.3 Rear plate of DS-232P and DS-252P 1.4 Chief Introduction about Function Motion Detection: In the surveillance area, the appearing motion object will trigger alarm. User can select suitable sensitivity level with corresponding environment.
Page 10
OSD (On Screen Display): The camera supports friendly menu interface on the screen, and it’s convenient for user selecting expected function. White Balance: Because the camera could not adjust the color temperature according to the light alteration as the eyes, that will cause color deviation. White balance is the white rendition ability of the camera to adjust the problem according to the environment automatically.
Before mounting, please make sure that the device in the package is in good condition and all the assembly parts are complete. 2.1 Lens The lens of the automatic focus camera were installed inside of the camera, 232 series cameras with f=3.9-85.8mm, 252 series cameras with f=3.84-88.4mm.
The menu functions of the DS-2CZ232P/N will be introduced in this chapter. The first part is the instruction of keys and menu structure, the second part is to introduce the menu functions of all the items. 3.1 Keys Introduction In this section, it will introduce the keys on the rear plate. 3.1.1 Setting buttons Fig 3.1 The keys of camera There are two work modes for the setting buttons: Common and Menu modes.
3.1.3 Alarm in, GND, Alarm output, Alarm output Com “ ” When motion detection module detects moving objects, it will trigger alarm signal. 3.1.4 Power supply “ ” Before connecting power supply adapter to camera, please check the anode and cathode. 3.1.5 Interface Definition DS-2CZ232P interface definition: Zoom (Wire Control Port)
DS-2CM232P interface definition: Pin number Name Voltage CMOS 5V,series receive pin CMOS 5V,series send pin Series GND DC IN 12VDC±10% Power supply GND CVBS OUT 1.0V±0.2V Video Output Composite Video GND Fig 3.3 DS-2CM232P interface definition table 3.2 OSD Menu Configuration In this section, it will introduce the menu of DS-2CZ232P.
3.2.1 Menu Structure 1. CAM ID OFF/001~254,Edit camera ID number 2. Exposure Auto:Auto mode, Auto Iris,AGC , AES 1/50 AI…:Auto Iris, AGC, AES (1/50~1/10000) AE…:AES,AGC(Low、High、Close),AI(F1.6~F5.6) Manual…:Shutter, IRIS,AGC can be set by manual. 3. AGC Low/High/Close, if the exposure mode is Auto or AI, AGC will not be set ,it display “---” 4.
Main Menu CAM ID OFF/001—254 Shutter Auto/AI…/AE…/Manual… Low/High/Close ATW1/ATW2/Auto/Manual… Auto…/Manual/One Focus Color/B/W Color…/Auto…/B/W… Motion D Open…/Close Special … Exit Default/Abort/Save Fig 3.7 Main Menu structure 3.2.2 Exposure The iris can control output video signal according to the different intensity of light. (This product is already equipped with iris.) The “F”(F1.6~F5.6) value of the iris can be set by user.
temperature. If selecting the ATW mode, the camera will continue monitoring the color temperature according to the surrounding light and adjust WB based on the color temperature. Including ATW1, ATW2, Auto, and Manual modes. ATW1/ATW2/Auto/Manual… Setup User/3200K/6300K (+1F)--------|---------- Blue (-53 ) -|------------------ Back Fig 3.9 white balance setup ATW1: Camera recover color automatically based on TTL algorithm, temperature range is approximate from...
(b). If the exposure mode is manual or AE, the AGC should be set as High. 3.2.7 Motion Detection In Motion Detection, the Motion D functions, sensitivity and motion areas can be set by manual. After the setup, user can detect the motion situation of the intruder. The motion D has two work modes: When Motion D is Close, if alarm input occurs, the alarm output will directly respond.
Page 21
Right,Up Button Figure 3.12 BLC When select “Off”, camera will not take back light compensation. RS-485 Press MENU button to enter RS485 setup interface: RS485 Protocol PELCO-D Baud 2400 (1200, 2400, 4800, 9600, 19200, 38400, 115200 optional) Address (000 t o 254 optional) Back Figure 3.13 RS-485 Setup Interface POS/ NEG...
3.2.9 Exit Exit option is used for quit setting Menu, and return to normal work mode. Abort: Neglect all modifications, and resume the original setup. Save: Save all modifications. Default: Neglect all modifications, resume the default factory setup.
The menu functions of the DS-2CZ232P will be introduced in this chapter. The first part is the instruction of keys and menu structure, the second part is to introduce the menu functions of all the items. 4.1 Keys Introduction In this section, it will introduce the keys on the rear plate. 4.1.1 Setting buttons Fig 4.1 The keys of camera There are two work modes for the setting buttons: Common and Menu modes.
4.1.3 Alarm in, GND, Alarm output, Alarm output Com “ ” When motion detection module detects moving objects, it will trigger alarm signal. 4.1.4 Power supply “ ” Before connecting power supply adapter to camera, please check the anode and cathode.
DS-2CM252P interface definition Pin number Name Voltage CMOS 5V,series receive pin CMOS 5V,series send pin Series GND DC IN 12VDC±10% Power supply GND CVBS OUT 1.0V±0.2V Video Output Composite Video GND Fig 4.3 DS-2CM252P interface definition table 4.2 OSD Menu Configuration In this section, it will introduce the menu of DS-2CZ252P.
Page 27
Manual…:Shutter, IRIS, AGC can be set by manual. 3. AGC Low/High/Close, if the exposure mode is Auto or AI, AGC will not be set ,it display “---” 4. WB ATW1/ATW2/Auto/Manual… 5. AF Auto…:To enter submenu and set the focus mode, sensitivity and the least focus distance --- (1cm、50cm、1m) Manual One focus: triggered by button once, then turn to manual mode.
Main Menu CAM ID OFF/001—254 Shutter Auto/AI…/AE…/Manual… Low/High/Close ATW1/ATW2/Auto/Manual… Auto…/Manual/One Focus Day…/Auto…/Night… Motion D Open…/Close Special … Exit Default/Abort/Save Fig 4.7 Main Menu structure 4.2.2 Shutter The iris can control output video signal according to the different intensity of light. (This product is already equipped with iris.) The “F”(F1.6~F5.6) value of the iris can be set by user.
4.2.4 White Balance In the white balance options, user can set the white balance function to ensure it can render normal white in any color temperature. If selecting the ATW mode, the camera will continue monitoring the color temperature according to the surrounding light and adjust WB based on the color temperature. Including ATW1, ATW2, Auto, and Manual modes.
4.2.6 Day / Night Optional day to night modes: Auto day switch to night, day mode, night mode. Auto day switch to night: Camera will switch between color and B/W according to the environment illumination. Under low illumination condition, IR filter will move away and switch to B/W mode to improve the sensitivity. Day Mode: IR filter will move into, the image back to normal status.
4.2.7 Motion Detection In Motion Detection, the Motion D functions, sensitivity and motion areas can be set by manual. After the setup, user can detect the motion situation of the intruder. The motion D has two work modes: When Motion D is Close, if alarm input occurs, the alarm output will directly respond.
Page 32
Right Up Button Figure 4.16 BLC When select “Off”, camera will not take back light compensation. RS-485 Press MENU button to enter RS485 setup interface: RS485 Protocol PELCO-D (1200、2400、4800、9600、19200、38400、115200 optional) Baud 2400 (000---254 optional) Address Back Figure 4.17 RS-485 Setup Interface POS/ NEG Move cursor to “POS / NEG”, and press left / right to select POS or NEG.
4.2.9 Exit Exit option is used for quit setting Menu, and return to normal work mode. Abort: Neglect all modifications, and resume the original setup. Save: Save all modifications.
Auto White Balance Gain Correction) Motion Detection On / Off (Zone, sensitivity) Special Function BLC, POS/NEG, Zoom speed(4 levels), Definition Communication HIKVISION protocol, compatible of SONY VISCA protocol Interface Power Supply 9-12V DC Working Temperature -10℃ ~ 60℃ Power Consumption...
ATW1 / ATW2 /Auto / Manual( Pre-set 3200K, Pre-set 5600K, R / G Gain Correction) Motion Detection On / Off (Zone, Sensitivity) Special Function BLC, POS/NEG, Zoom Speed (4 levels), Definition Communication HIKVISION protocol, compatible of SONY VISCA protocol Interface Power Supply 12VDC, ±10% Working Temperature -10℃ ~ 60℃ Power Consumption 4W MAX 61.2 ×...
Table 5 DS-2CZ282P Parameter Model DS-2CZ282P Image Sensor 1/4"SONY Interline Transfer Super HAD CCD Signal System Effective Pixels 752(H)×582(V) Synchronous Internal Synchronization Day:540TVL Horizontal Resolution Night:600TVL Privacy 16 areas (area/position adjustable) Video Output 1.0Vp-p Composite Output(75Ω/BNC) S/N Ratio More than 52dB Day &...
Table 6 DS-2CZ292P Parameter Model DS-2CZ292P Image Sensor 1/4"SONY Interline Transfer Super HAD CCD Signal System Effective Pixels 752(H)×582(V) Synchronous Internal Synchronization Day:540TVL Horizontal Resolution Night:600TVL Privacy 16 areas(area/position adjustable) Video Output 1.0Vp-p Composite Output(75Ω/BNC) S/N Ratio More than 52dB Day &...