Honeywell 40015 User Manual page 3

WALL CONTROL UNIT
WALL OUTLET BOX
FIG 5
WALL CONTROL INSTALLATION
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the
following measures: Reorient or relocate the receiving antenna. Increase
the separation between the equipment and receiver. Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. ‐‐Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of
this device could void the user's authority to operate the equipment.
FCC ID：KUJCE10005 & KUJCE10006
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
One Year Limited Warranty
If you have questions regarding this product, before returning
to your retailer, call our customer service department toll free
at 1-877-580-4359
Model 40015 / Item # 0374122
User Guide (For Handheld Control)
ACTIVATING THE LEARNING PROCESS (SMART SYNC)
1. After installation is complete and power is turned on, remove the battery cover on
transmitter. Insert batteries (2 AAA, included).
NOTE: Do not mix old and new batteries, alkaline, standard (carbon‐zinc) or
rechargeable (nickel‐cadmium) batteries.
2. Turn off the main power and re‐start the power again. Press and hold the "FAN OFF"
button on transmitter for 3 seconds. Fan will turn on at high speed and light (if
installed) blinks 3 times. This confirms that the SMART SYNC setting is active. You now
have 30 seconds to press the FAN OFF button. Tap the FAN OFF button again to turn
WALL PLATE
Available at www.HoneywellStore.com
off the fan.
3. If user cannot finish the setting within the 30 seconds time
frame the main power must be turned off and re‐started
again. This will reset the unit. Repeat step 2 until the
LEARNING feature is activated as indicated.
NOTE: User must press "LEARN" key within 30 seconds after
main power is turned on. It is not necessary to redo the
LEARNING setting if just replacing batteries.
DIMMER ON/OFF SETTING (D/ O SWITCH)
)
Slide the D/O switch, located in the battery compartment (See
FIG. 1), to match the bulb type in your fan. "D" is for
incandescent bulbs and "O" indicates compact fluorescent bulbs
(CFL). Use a small screwdriver or ballpoint pen to slide firmly left
or right.
CAUTION: Incorrect bulb setting can damage the receiver.
TRANSMITTER OPERATION (FIG.2)
)
High / Medium / Low Speed – Tap lightly to turn the fan on at
high, medium or low speed respectively.
Fan Off – Tap lightly to turn the fan off.
Light – Tap lightly to turn light on or off.
Dimmer – Hold down for 2 seconds to cycle through dimmer
setting. The light button has an auto resume feature so the light
will re‐activate at the same brightness as the last time it was
turned off.
NOTE: The dimmer function does not work with CFL bulbs.
D/O – Set the light for use with incandescent bulbs or compact
fluorescent bulbs (CFL).
NOTE: Factory default setting is CFL.
INSTALLING THE WALL MOUNT BRACKET
S
1. Locate wall mount in a convenient location
2. Use two screws (included) and wall anchors to install wall
mount bracket as shown in FIG. 3 (Tools required for assembly:
Philips screwdriver, not included)
S
The Honeywell Trademark is used under license from Honeywell
International Inc. Honeywell International Inc. makes no representations
or warranties with respect to this product.
This product is manufactured for:
Hong Kong China Electric Appliance Manufacture Co., Ltd.
3059 Forest Hill Irene Rd, Ste 103
Germantown, TN 38138
1‐877‐580‐4359