1. Manuals
  2. Brands
  3. GE Manuals
  4. Oven
  5. r08654v-1
  6. Installation instructions manual

GE r08654v-1 Installation Instructions Manual

Built-in wall oven 27” (68.6 cm) and 30” (76.2 cm) models
Hide thumbs
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

Installation
Instructions
If you have questions, call 1.800.GE.CARES or visit our website at:
ge.com

Before You Begin

Read these instructions carefully and completely.
IMPORTANT
•
instructions for local inspector's use.
IMPORTANT
•
governing codes and ordinances.
• Note to Installer—Be sure to leave these
instructions with the consumer.
• Note to Consumer—Keep these
instructions for future reference.

Parts Included

(Appearance will vary)
Screws For Installation
(8-18 x .750 flat head
Phillips wood screws)
WB07T10578 – Black
WB07T10579 – SS
Optional 27" (68.6 cm)
Metal Bottom Trim Assembly
(on some models or can be
purchased separately)
31-10647-3
11-07 JR
—Save these
—Observe all
27" (68.6 cm)
Metal Bottom Trim
30" (76.2 cm)
Metal Bottom Trim
Assembly
Built-In Wall Oven
27" (68.6 cm) models
JKS10, JKP30, JKP35, JKP55, JKP70, JKP75,
PK916, PK956, ZEK938, ZEK958
30" (76.2 cm) models
JTP30, JTP35, JTP55, JTP70, JTP75, PT916,
PT920, PT956, PT960, ZET938, ZET958
• Proper installation is the responsibility
of the installer and product failure due
to improper installation is NOT covered
under warranty.
• NOTE—This appliance must be properly
grounded.
ATTENTION INSTALLER
•
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT permitted
on these products.
Materials Needed
Strain Relief Clamp
for 1/2" conduit
Tools Needed
1/8" (3 mm) Drill Bit and
Electric or Hand Drill
1
Wire Nuts
Junction
Box
36" (91 cm)
of String
Phillips
Screwdriver

Advertisement

Table of Contents
loading

Related Manuals for GE r08654v-1

Summary of Contents for GE r08654v-1

  • Page 1: Installation Instructions

    Installation Instructions If you have questions, call 1.800.GE.CARES or visit our website at: ge.com Before You Begin Read these instructions carefully and completely. IMPORTANT • —Save these instructions for local inspector’s use. IMPORTANT • —Observe all governing codes and ordinances.

  • Page 2: Important Safety Instructions

    • Be sure your oven is installed properly by a qualified installer or service technician. • Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury.
  • Page 3 Door removal is not a requirement for installation of the product, but is an added convenience. To remove the door: Open the oven door as far as it will go. Push both hinge locks down toward the door frame, to the unlocked position.
  • Page 4 If the cabinet does not have a solid bottom, two braces or runners must be installed level with the bottom of the cutout to support the weight of the oven. For single ovens, the runners and braces must support 150 lbs (68 Kg).
  • Page 5 If the cabinet does not have a solid bottom, two braces or runners must be installed to support the weight of the oven. For double ovens, the runners and braces must support 300 lbs (135 Kg).
  • Page 6 For JKS10, JKP30, JKP70, PK916, ZEK938 models only. Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models. 25” (63.5 cm) Top and/or side fillers may be necessary...

  • Page 7: Warming Drawer

    1” (2.5 cm) Min. Above Toekick or Adjust to Oven Installation Height NOTE: Additional clearances between cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height.

  • Page 8: Microwave Oven

    Per Warming Drawer Requirement NOTE: Additional clearances may be required. Check to be sure the oven supports above the Warming Drawer do not obstruct the required interior depth and height. The middle rail separating the openings may need to be larger than the 2”...
  • Page 9 If the cabinet does not have a solid bottom, two braces or runners must be installed level with the bottom of the cutout to support the weight of the oven. For single ovens, the runners and braces must support 150 lbs (68 Kg).
  • Page 10 If the cabinet does not have a solid bottom, two braces or runners must be installed level with the bottom of the cutout to support the weight of the oven. For double ovens, the runners and braces must support 275 lbs (124 Kg).
  • Page 11 Cutout for 30″ only Under Counter For JTP30, JTP70, PT916, PT920, ZET938 models only. Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models.
  • Page 12 1” (2.5 cm) Min. Above Toekick or Adjust to Oven Installation Height NOTE: Additional clearances between cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height.
  • Page 13 Per Warming Drawer Requirement NOTE: Additional clearances may be required. Check to be sure the oven supports above the Warming Drawer do not obstruct the required interior depth and height. The middle rail separating the openings may need to be larger than the 2”...

  • Page 14: Electrical Connections

    Position the conduit in such a manner that it will lie on top of the oven in a natural loop when the oven is installed. You will need to purchase...
  • Page 15 (white or gray) in accordance with local codes, using a wire nut. d. Connect the oven red lead to the branch circuit red lead and the oven black lead to the branch circuit black lead in accordance with local codes, using wire nuts.

  • Page 16: Securing The Oven In The Opening

    Carefully push against oven front frame. Do not push against outside edges. c. As you slide the oven back, pull the string so that the conduit will lie on top of the oven in a natural loop.
  • Page 17 Installation Instructions Preparing for the Bottom Trim Installation a. With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening. For 27″ (68.6 cm) b. Using the trim models with Lower as a template,...

  • Page 18: Replacing The Oven Door

    Hinge Arm Bottom Edge of Slot Hinge Notch Open the oven door as far as it will open. Push the hinge locks up against the front frame of the oven cavity, to the locked position. Hinge in...

  • Page 19: Operation Checklist

    Remove all items from the inside of the oven. Check that conduit is securely connected to the junction box. Turn on the power to the oven. (Refer to your Owner’s Manual.) Verify that the bake and broil units, and all cooking functions operate properly.
  • Page 20 Notes...

  • Page 21: Instrucciones De Instalación

    Instrucciones de instalación ¿Preguntas? Visite nuestro sitio en la Web: ge.com Antes de empezar Lea estas instrucciones cuidadosa y completamente. IMPORTANTE • —Guarde estas instrucciones y téngalas disponibles para el inspector local. IMPORTANTE • —Observe todos los códigos y ordenanzas vigentes.

  • Page 22: Instrucciones De Seguridad Importantes

    Instrucciones de instalación INSTRUCCIONES DE SEGURIDAD IMPORTANTES Para su seguridad • Cerciórese de que su horno sea instalado adecuadamente por un instalador calificado o por un técnico de servicio. • Cerciórese de que su horno esté firmemente instalado en un gabinete que esté firmemente adherido a la estructura de la casa.

  • Page 23: Lista De Control Antes De La Instalación

    Parrillas del horno EASY INSTALLATION OF YOUR NEW 30" WALL OVEN Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully.
  • Page 24 Instrucciones de instalación Corte para los hornos de una unidad de 27″ Para los modelos JKS10, JKP30, JKP70, PK916, ZEK938 solamente. Ancho del gabinete 27” (68,6 cm) Ancho del corte 25” (63,5 cm) Mín. 25 1/4” (64,1 cm) Permita 1” (2,5 cm) Máx.
  • Page 25 Instrucciones de instalación Corte para los hornos de dos unidades de 27″ Para los modelos JKP35, JKP55, JKP75, PK956, ZEK958 solamente. 5” (12,7 cm) Máx. espacio para el lado izquierdo o derecho Ancho del gabinete 27” (68,6 cm) Ancho del corte 25”...
  • Page 26 Instrucciones de instalación Corte para los hornos de una unidad– debajo de la superficie del gabinete de 27″ Para los modelos JKS10, JKP30, JKP70, PK916, ZEK938 solamente. Las estufas eléctricas o de gas se pueden instalar sobre este horno. Consulte las instrucciones de la estufa para el tamaño del corte.
  • Page 27 Disyuntor para 27″ para hornos individuales o dobles empotrados – Sobre una gaveta de calentamiento Para los modelos JKS10, JKP30, JKP35, JKP55, JKP70, JKP75, PK916, PK956, ZEK938, ZEK958 solamente. Horno individual de 27″ (68,6 cm) sobre una gaveta de calentamiento Para la gaveta de calentamiento...
  • Page 28 Disyuntor para 27″ individuales – Debajo de un Advantium o de un horno de microondas o Entre un horno Advantium o un horno de microondas y Gaveta de calentamiento Para los modelos JKS10, JKP30, JKP70, PK916, ZEK938 solamente. Horno individual de 27″ (68,6 cm) debajo de un horno Advantium o un horno de microondas Por Advantium o horno...
  • Page 29 28 5/8” 28 5/8" MAX. (72,7 cm) Máx. Permita 11/16” ALLOW 11/16" FOR (1,75 cm) para OVERLAP OF THE sobrepaso del OVEN OVER SIDE Abertura horno sobre los EDGES OF CUTOUT entre los bordes laterales paredes THE OPENING del corte...
  • Page 30 28 5/8” 28 5/8" MAX. (72,7 cm) Máx. Permita 11/16” ALLOW 11/16" (1,75 cm) para FOR OVERLAP Abertura sobrepaso del OF THE OVEN entre los horno sobre los OVER SIDE EDGES paredes bordes laterales OF CUTOUT interiores del corte debe estar un mínimo...
  • Page 31 Instrucciones de instalación Corte para los hornos de una unidad – debajo de la superficie del gabinete de 30″ Para los modelos JTP30, JTP70, PT916, PT920, ZET938 solamente. Las estufas eléctricas o de gas se pueden instalar sobre este horno. Consulte las instrucciones de la estufa para el tamaño del corte.
  • Page 32 Disyuntor para 30″ para hornos individuales o dobles empotrados – Sobre una gaveta de calentamiento Para los modelos JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958 solamente. Horno individual de 30″ (76,2 cm) sobre una gaveta de calentamiento Para la gaveta de calentamiento...
  • Page 33 Disyuntor para 30″ individuales – Debajo de un Advantium o de un horno de microondas o Entre un horno Advantium o un horno de microondas y Gaveta de calentamiento Para los modelos JTP30, JTP70, PT916, PT920, ZET938 solamente. Horno individual de 30″ (76,2 cm) debajo de un horno Advantium o un horno de microondas Por Advantium o horno...
  • Page 34 Instrucciones de instalación Conexiones eléctricas ATENCIÓN AL INSTALADOR: Todos los hornos eléctricos de pared deben ser cableados directamente en una caja de conexión. Una “enchufe-receptáculo” NO ES permitido en estos productos. NO acorte el conducto flexible. La abrazadera para controlar la presión debe estar firmemente adherida a la caja de conexión y el conductor flexible debe estar firmemente adherido a la abrazadera.
  • Page 35 Instrucciones de instalación B3 Conexión para nueva construcción y de circuito ramal de cuatro conductores • Cuando se instale en una construcción nueva, o • Cuando se instale en una casa móvil, o • Al instalar en un vehículo de recreacíon, o •...

  • Page 36: Posición Firme Del Horno En La Abertura

    Instrucciones de instalación Posición firme del horno en la abertura Cómo deslizar el horno en el interior de la abertura a. Coloque (sin atar) una cuerda de 36” (91 cm) alrededor del conductor antes de deslizar el horno en su lugar. Esto evitará que el conducto se caiga detrás del horno.
  • Page 37 Instrucciones de instalación Preparación para la instalación de la moldura de fondo a. Con el horno instalado, tome la moldura de fondo y céntrela en el borde frontal del fondo de la abertura del gabinete. b. Usando la moldura Para modelos de 27” (68,6 cm) con como una plantilla, moldura inferior en...

  • Page 38: Cómo Instalar La Puerta Del Horno

    Instrucciones de instalación Cómo instalar la puerta del horno NOTA: La puerta del horno es pesada. Quizás necesite ayuda para levantar y deslizar la puerta hacia abajo sobre las bisagras. No levante la puerta por la empuñadura. Levante la puerta del horno colocando una mano en cada lado.

  • Page 39: Lista De Control Antes De La Prueba

    Instrucciones de instalación Lista de control antes de la prueba Retire cualquier cinta de protección y etiqueta que todavía esté presente. Revise para asegurarse de que todos los alambres estén bien conectados y no aplastados o en contacto con partes móviles.
  • Page 40 Notas...

This manual is also suitable for:

Pt920smssJks10Jkp30Jkp35Jkp55Jkp70 ... Show all

Table of Contents