Download
Share
Print this page
GE JKS10 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. GE Manuals
  4. Oven
  5. JKS10
  6. Installation instructions manual
GE JKS10 Installation Instructions Manual

GE JKS10 Installation Instructions Manual

Built-in wall oven 27" (68.6 cm) & 30" (76.2 cm) models
Hide thumbs Also See for JKS10:

Advertisement

Available languages

Available languages

Quick Links

Download this manual See also: Owner's Manual, Technical & Service Manual
Ilnstallat!on
nstruct=ons
Built-In Wall Oven
27" (68.6 cm) models
JKS10, JKP30, JKP35, JKP55, JKP70, JKP75,
PK916, PK956, ZEK938,
ZEK958
30" (76.2 cm) models
JTP30, JTP35, JTP55, JTP70, JTP75, PT916,
PT920, PT956, PT960, ZET938,
ZET958
If you have questions, call 1.800.GE.CARES
or visit our website at:
ge.com
Before You Begin
Read these instructions carefully and completely.
• IMPORTANT-save
these
instructions
for local inspector's
use.
• IMPORTANT-observe all
governing
codes and ordinances.
• Note to Installer--Be
sure to leave these
instructions
with the consumer.
• Note to Consumer--Keep
these
instructions
for future
reference.
• Proper installation
is the responsibility
of the installer
and product
failure
due
to improper
installation
is NOT covered
under warranty.
• NOTE--This
appliance
must be properly
grounded.
• ATTENTION INSTALLER
All electric wall ovens must be hard wired
(direct wired)
into an approved junction
box. A plug and receptacle
is NOT permitted
on these products.
Parts Included
(Appearance
will vary)
Screws For Installation
(8-18 x .750 flat head
Phillips wood screws)
WB07T10578 - Black
WB07T10579 - SS
Optional 27" (68.6 cm)
Metal Bottom Trim Assembly
(on some models or can be
purchased separately)
27" (68.6 cm)
Metal Bottom Trim
30" (76.2 cm)
Metal Bottom Trim
Assembly
Materials Needed
Strain Relief Clamp
Junction
for 1/2" conduit
Box
Wire Nuts
36" (91 cm)
of String
Tools Needed
1/8" (3 mm) Drill Bit and
Electric or Hand Drill
Phillips
Screwdriver
31-10647-3
11-07 JR

Advertisement

loading

Related Manuals for GE JKS10

Summary of Contents for GE JKS10

  • Page 1 Built-In Wall Oven 27" (68.6 cm) models JKS10, JKP30, JKP35, JKP55, JKP70, JKP75, Ilnstallat!on PK916, PK956, ZEK938, ZEK958 nstruct=ons 30" (76.2 cm) models JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958 If you have questions, call 1.800.GE.CARES or visit our website at: ge.com...

  • Page 2: Installation Instructions

    Installation instructions PORTANT SAFETY I ST CTIONS lectrical For Your Safety Requirements • Be sure your oven is installed properly cont. a qualified installer or service technician. • Be sure the oven is securely installed in a Rating plate is located on oven side trim, side front frame or lower front frame.
  • Page 3 Insta ion instructions Pre-lnstallation Chec Door removal is not a requirement ALL INSTALLATION INFORMATION installation of the product, but is an added convenience. To remove the door: ON THE FOLLOWING PAGES IS TO BF USED FOR SINGLE AND DOUBLE OVEN INSTALLATION! Open the oven door as far as it will go.
  • Page 4 Installation instructions uilt-ln Cutout for 27" (68.6 c )Single Ovens on y For JKS10, JKP30, JKP70, PK916, ZEK938 models only. Cabinet Width 27" (68.8 cm) 5" (12.7 cm) Max. from the Recommended left or right Cutout Location Cabinet_ Junction Location...
  • Page 5 Installation instructions Cutoutfor 27"(68.6 Ovensonly For JKP35, JKP55, JKP75, PK956, ZEK958 models only. 5" Cabinet Width (12.7 cm) 27" (68.6 cm) Max. from the left or Recommended Cabinet right Cutout Location from Floor 13 1/4" (33.7 cm) Junction Box (68.6 cm) _ Cutout Location Cutout Depth...
  • Page 6 Installation instructions Cutout for 27" (68.6 c_)Single Built-in Ovens only Under Counter For JKS10, JKP30, JKPT0, PK916, ZEK938 models only. Gas or electric cooktops be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models.
  • Page 7 Cabinetry for 27" (68.6 c _)Single or uilt-ln Ovens only- Over a Drawer For JKS10, JKP30, JKP35, JKP55, JKPT0, JKP75, PK916, PK956, ZEK938, ZEK958 models only. Double 27" (68.6 cm) Single 27" (68.6 cm) Oven Over Oven Over a Warming Drawer...
  • Page 8 Belowan Advantiumor ;rowave Oven or Betweenan Advantiumor crowave Ovenand a WarmingDrawer For JKS10, JKP30, JKP70, PK91& ZEK938 models only. Single 27" (68.6 cm) Oven Single 27" (68.6 cm) Oven Between an Advantium or Below an Advantium or Microwave Oven and a...
  • Page 9 Installation instructions Cutout for 30"(76.2 c )Sing Built-in Ovensonly For JTP30, JTP70, PT916, PT920, ZET938 models only. Cabinet Width 30" (76.2 cm) Cutout 9 1/2" (24.1 cm) Width Junction Box Recommended 28 1/2" (72.4 cm) Location Cutout Location (junction box 5/8"(72.7 ore) may be from Floor...
  • Page 10 Installation instructions Cutout for 30"(76.2 cm) Ovensonly For JTP35, JTP55, JTP75, PT956, PT960, ZET958 models only. 9 1/2" Cutout Cabinet Width 30" (76.2 cm) Width (24.1 cm) Junction Box 28 1/2" (72.4 cm) Recommended Min. (junction box Cutout Location 28 5/8" (72.7 cm) may be Max.
  • Page 11 Installation instructions Cutout for 30"(76.2 Single lit-in Ovens only Under Coun :r For JTP30, JTPT0, PT916, PT920, ZET938 models only. Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on 240V / 208V top of oven for approved cooktop models.
  • Page 12 Cabinetry Double Cutout for 30"(76.2c_) Single or L_i -in Ovens only- Over a _rrning Drawer For JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958 models only. Single 30" (76.2 cm) Double 30" (76.2 cm) Oven Over a Warming Oven Over a Warming Drawer Drawer...
  • Page 13 Cabinetry Cutoutfor 30"<76.2 o_)SingleOvensonly- Belowan Advantium or _-rowaveOven or Betweenan Advantiumor crowave Ovenand a WarmingDrawer For JTP30, JTP70, PT916, PT920, ZET938 models only. Single 30" (76.2 cm) Oven Single 30" (76.2 cm) Oven Below an Advantium or Between an Advantium or Microwave Oven Microwave Oven and a Warming Drawer...

  • Page 14: Attention Installer

    Installation instructions Electrical Connections Turn off the circuit breaker or remove ATTENTION iNSTALLER fuses to the oven branch circuit. All electric wall ovens must be hard wired With the oven supported on a table or (direct wired) into an approved junction platform in front of the cabinet opening,...
  • Page 15 Installation instructions New Construction and Three=Conductor Branch Four=Conductor Branch Circuit Connection Circuit Connection When connecting to a three-conductor branch circuit, if local codes permit: • When installing in new construction, a. Connect the bare oven ground conductor • When installing in a mobile home, or with the crimped neutral (white) lead to •...
  • Page 16 Installation instructions Securing the Oven e Openin Sliding the Oven into the Drilling the Pilot Holes and Opening Mounting the Oven a. Loop (do not tie) a 36" (91 cm) string around the conduit before the oven is slid NOTE: Before drilling the pilot holes, into place.
  • Page 17 Installation instructions Installing the Metal Preparing for the Bottom Bottom Trim Trim Installation Place the bottom metal trim centered over a. With oven installed, take the bottom trim the pre-drilled mounting holes. Tape the and center it on the bottom front edge of edges of the trim down to maintain the the cabinet opening.
  • Page 18 Installation instructions Replacing the Oven Door Open the oven door as far as it NOTE: The oven door is heavy. You will open. may need help lifting the door high enough to slide it into the hinge slots. Push the hinge locks up against the Do not lift the door by the handle.

  • Page 19: Operation Checklist

    Installation instructions Pre-Test C ec Check that the bottom trim is installed Remove all protective film, if present, properly (see page 17). and any stickers. Check to be sure that all wiring is Check to be sure the mounting screws are installed and flush with the side trim secure and not pinched or in contact...
  • Page 20 Notes...

  • Page 21: Antes De Empezar

    Horno de pared empotrado Instrucciones Modelos de 27" (68,6 cm) JKS10, JKP30, JKP35, JKP55, JKP70, JKP75, de instalacibn PK916, PK956, ZEK938, ZEK958 Modelos de 30" (76,2 cm) JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958 I &Preguntas? Visite nuestro sitio en la Web: ge.com...

  • Page 22: Instrucciones Importantes

    Instrucciones de instalacibn INSTRUCCIONES DE SEGURIDAD IMPORTANTES Requisitos el ctricos Para su seguridad cont. * Cerciorese de que su horno sea instalado adecuadamente por un instalador calificado La placa de potencia se encuentra en la moldura lateral o por un tecnico de servicio.
  • Page 23 Instrucciones de instalacibn p Lista de control antes de la instalacibn No es necesario retirar la puerta para la instalaci6n del producto, pero hacerlo facilita iTODA LA INFORMACION PARA LA INSTALACION EN LAS PAGINAS la instalaci6n. Para retirar la puerta: SIGUIENTES ES PARA SER USADA LA INSTALACION...
  • Page 24 Instrucciones de instalacibn l-A-] Corte para los hornos de una unidad de 27" (68,6 cm)solamente Para los modelos JKS10, JKP30, JKP70, PK916, ZEK938 solamente. 5" (12,7 cm) M_x. espacio para Ancho del el lado izquierdo oderecho gabinete 27" (68,6 cm) Ancho del_ ¢...
  • Page 25 Instrucciones de instalacibn I-A-1Corte para los hornos de dos unidades de 27" solamente (68,6 cm) Para los modelos JKP35, JKP55, JKP75, PK956, ZEK958 solamente. 5" (12,7 cm) Ancho del M&x. espacio para el lado izquierdo gabinete 27" (68,6 cm) o derecho Ancho del _ Ubicaci6n gabinete...
  • Page 26 Corte para los hornos de una unidad-debajo de la superficie del gabinete de 27"(68,6 c m) s olamente Para los modelos JKS10, JKP30, JKP70, PK916, ZEK938 solamente. Las estufas el_ctricas o de gas se pueden instalar sobre este horno. Consulte las instrucciones de la estufa para el tamaho del corte.
  • Page 27 27"(68,6 para hornos individuales o dobles empotrados- Sobre una gaveta de calentamiento Para los modelos JKS10, JKP30, JKP35, JKP55, JKP70, JKP75, PK916, PK956, ZEK938, ZEK958 solamente. Horno individual de 27" Horno doble de 27" (68,6 cm) sobre una (68,6 cm) sobre una...
  • Page 28 - Debajo d eunAdvantium odeun horno d emicroondas oEntre unhorno A dvantium unhorno demicroondas yGaveta d ecalentamiento Para los modelos JKS10, JKP30, JKP70, PK916, ZEK938 solamente. Hornoindividual d e27"(68,6cm) Hornoindividual d e 27"(68,6cm) EntreunhornoAdvantium o debajode unhornoAdvantium o un hornode microondas...
  • Page 29 Instrucciones de instalacibn Corte para los hornos de una unidad de 30" solamente (76,2 cm) Para los modelos JTP30, JTP70, PT916, PT920, ZET938 solamente. Ancho del Ubicacion Ancho 9 1/2" de la caja 30" (76,2 cm) gabinete del corte (24,1 cm) de conexi6n 28 1/2"...
  • Page 30 Instrucciones de instalacibn Corte para los hornos de dos unidades de 30" (76,2 cm)solamente Para los modelos JTP35, JTP55, JTP75, PT956, PT960, ZET958 solamente. Ancho Ancho del del corte 9 112" (24,1 cm) Ubicaci6n 28 1/2" gabinete 30" (76,2 cm) M&x.
  • Page 31 Instrucciones de instalacibn Corte para los hornos de una unidad -debajo de la superficie del gabinete de 30" cm)solamente (76,2 Para los modelos JTP30, JTP70, PT916, PT920, ZET938 solamente. Las estufas el_ctricas o de gas se pueden instalar sobre este horno.
  • Page 32 Gabinetes Disyuntor para 30"(76,2 cm)solamente para hornos individuales o dobles empotrados- Sobre una gaveta de calentamiento Para los modelos JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958 solamente. Horno individual de 30" Horno doble de 30" (76,2 cm) sobre una (76,2 cm) sobre una gaveta de calentamiento gaveta de calentamiento...
  • Page 33 Gabinetes Disyuntor para 30" para hornos (76,2cm)Solamente individuales - Debajo d eunAdvantium o deun horno demicroondas o Entre unhorno Advantium o unhorno demicroondas y Gaveta d ecalentamiento Para los modelos JTP30, JTP70, PT916, PT920, ZET938 solamente. Hornoindividual d e30"(76,2cm) Hornoindividual d e 30"(76,2cm) EntreunhornoAdvantium o debajode unhornoAdvantium o un hornode microondas...
  • Page 34 Instrucciones de instalacibn IBIConexiones el ctricas ATENCION AL Desconecte el interruptor del circuito o retire los fusibles que alimentan INSTALADOR: circuito ramal del horno. Con el horno enfrente de la abertura Todos los hornos electricos de pared deben gabinete, sobre una mesa o plataforma ser cableados directamente en una caja...
  • Page 35 Instrucciones de instalacibn Conexibn de circuito ramal [B3-] Conexibn para nueva i--- de tres conductores construccibn y de circuito ramal de cuatro conductores Cuando conecte un circuito ramal de 3 conductores, si los codigos locales Io • Cuando se instale en una construccion nueva, o permiten: •...
  • Page 36 Instrucciones de instalacibn Posicibn firme del horno en la abertura Cbmo deslizar el horno en Cbmo taladrar los orificios '---' el interior de la abertura '--' piloto y montar el horno a. Coloque (sin atar) una cuerda de 36" (91 cm) alrededor del conductor antes de NOTA: Antes de perforar...
  • Page 37 Instrucciones de instalacibn Preparacion para la instalacion Cbmo instalar la moldura de la moldura de fondo de fondo metalica a. Con el horno instalado, tome la moldura Coloque la moldura de fondo centrada sobre los orificios pre-taladrados. Adhiera los bordes fondo y centrela en el borde frontal del fondo de la moldura...
  • Page 38 Instrucciones de instalacibn 151Cbmo instalar la puerta del horno _'-_ Abra la puerta del horno hasta el NOTA: La puerta del horno es pesada. maximo. Quiz_s necesite ayuda para levantar y deslizar la puerta hacia abajo sobre Empuje los topes de las bisagras contra las bisagras.

  • Page 39: Lista De Control Antes De La Prueba

    Instrucciones de instalacibn Lista de control antes de la prueba Inspeccione la moldura de fondo para etire cualquier cinta de proteccion etiqueta que todavia este presente. cerciorarse de que esta instalada apropiadamente (ver pagina 17). los alambres esten bien conectados Inspeccione para cerciorarse de que los...
  • Page 40 Notas...

This manual is also suitable for:

Jkp35Jkp30Jkp75Pk916Pk956Zek938 ... Show all