Always there to help you Register your product and get support at www.philips.com/welcome PNS400/410BT Question? PNS500/510BT Contact Philips User manual...
Contents 1 Important Safety Notice 2 Yor navigation system Introduction What's in the box Overview of the main unit 3 Get started Connect power Switch the navigator on or off Use the bracket Use the touch pen For the first time use 4 Navigation Access navigation mode Choose a destination...
1 Important Safety Warning • To prevent possible hearing damage, do not listen at • Read and understand all instructions hight volume levels for long periods. before you use your apparatus. If damage is caused by failure to follow instructions, the warranty does not apply.
Any changes or modifications made to this This product complies with the radio device that are not expressly approved by interference requirements of the European Philips Consumer Lifestyle may void the user’s Community. authority to operate the equipment. A copy of the EC declaration of Conformity...
Page 6
Always bring your product to a professional to remove the built-in battery. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Philips is under license.
2 Yor navigation What's in the box system Check and identify the contents of your package: a The navigator b Vehicle power adaptor Introduction c Touch pen d Bracket & holder With the navigation system, you can: e USB cable •...
Overview of the main unit • Press and hold to turn on the navigator. b Indicator light • Light up when the navigator is charging. c Touch screen d Speaker e RESET • Restore default settings. • MINI USB socket for power charging and data transfer.
Use the controls only as stated in this user manual. Always follow the instructions in this chapter in sequence. If you contact Philips, you will be asked for the model and serial number of your apparatus. The model number and serial number are on the bottom of your apparatus.
Switch the navigator on or off Use the touch pen Caution Press and hold until the navigator is switched on or off. • The touch pen with a broken nib, ballpoint pen, as well as any sharp and rough objects may scratch and damage the touch screen.
4 Navigation Choose a destination You can set your destinations by one of following ways: Access navigation mode Press and hold to switch on the navigator. Tap [Navigation] to access navigation mode. » The navigation main menu is displayed in a few seconds. •...
Page 12
Tap [Navigate to] to start navigation. Type zip code on the keyboard, then select the zip code from the list. Set an address as destination Tap [Address]. Choose a country from the list. • To choose another country, tap • For the next time you use the system, the address will be searched in the country you previously selected.
Tap [Navigate to] to to start the navigation guidance. Find nearby You can search for a POI that is near to the place where you are. Tap [Find nearby]. In the displayed list, choose a POI category Enter latitude and longitude using the in which you are interested.
During navigation After you select the destination, tap [Navigate to] the start guidance and the navigation screen appears. • A:Rerouting button : calculates an alternative route. You will return on the navigation screen after 10 seconds if you make no modification. •...
Route profile • To select language or keyboard, tap • To save the changes, tap Tap one of the options to set the route profile. • To go back to top menu, tap . • [Fastest/Shortest] Choose between a route optimized for Alarm time or for distance.
last resort in your route search. If on the other hand, the value is set at 150% for a category, the roads in this category will be given preference. Plan a route You can plan your route in two ways: •...
Map Mode Map displays your current position on the map if navigation mode is not activated. If navigation is in progress, you can switch to map mode by tapping button J. • A: Go back to top menu. • B: Display the whole map. •...
To change the default password, tap [Modify the PIN]. • To change the default device name, tap [Modify the • Philips does not guarantee the compatibility with all name]. Bluetooth devices. • Before pairing a device with this system, read its user manual for Bluetooth compatibility.
» The following screen appears, tap the number using the keyboard. Transfer a call to mobile phone By default, the voice comes from the loudspeakers during a call. Tap . » The loudspeakers are muted, and the voice comes from your mobile phone only.
6 Adjust settings Settings Description [Backlight] Set the screen brightness and the backlight time. [Volume] Adjust the volume and screen tap sound. [Language] Set the OSD(on-screen display) languages. [GpsInfo] View the GPS information. [DateTime] Set date and time. [Calibration] Follow the on-screen instructions to calibrate the touch screen.
(W x H x D) 133.9 x 84.4 x 11.5 mm (PNS500/PNS510BT) Dimensions of 80.0 x 110.0 x 130.0 holder (W x H x D) Weight (main unit) 0.13 kg (PNS400/ PNS410BT) 0.16 kg (PNS500/ PNS510BT) Weight (holder) 0.10 kg Screen size 4.3 inches (PNS400/PNS410BT) 5.0 inches...
The system is already connected with requesting service. If the problem remains another Bluetooth-enabled device. unsolved, go to the Philips Web page (www. Disconnect that device or all other philips.com/support). When you contact Philips, connected devices and then try again.