GE 27955 User Manual

Model 27955
Interference Information
DECT 6.0 This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference; and (2) This device
must accept any interference received, including interference that may cause undesired
Optional/
operation.
This equipment has been tested and found to comply with the limits for a Class B
Additional
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
Cordless
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
Handset
in a particular installation.
Privacy of Communications may not be ensured when using this product.
Guide
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television
that is "receiving" the interference).
• Reorient or relocate and increase the separation between the telecommunications
equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from
that to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an
experienced radio/television technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful booklet, "How To Identify and
Resolve Radio/TV Interference Problems." This booklet is available from the U.S.
Government Printing Office, Washington, D.C. 20402. Please specify stock number 004-
000-00345-4 when ordering copies.
Notice: The changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Hearing Aid Compatibility (HAC)
This telephone system meets FCC standards for Hearing Aid Compatibility.
for use with Model 27951 & 27950
Licensing
Licensed under US Patent 6,427,009.
Equipment Approval Information
FCC RF Radiation Exposure Statement
Rights of the Telephone Company
This equipment complies with FCC RF radiation exposure limits set forth for an
Should your equipment cause trouble on y our line which may harm the telephone
uncontrolled environment. This equipment should be installed and operated with
network, the telephone company shall, where practicable, notify you that temporary
a minimum distance of 20 centimeters between the radiator and your body. This
discontinuance of service may be required. Where prior notice is not practicable and
transmitter must not be co-located or operated in conjunction with any other antenna or
the circumstances warrant such action, the telephone company may temporarily
transmitter."
discontinue service immediately. In case of such temporary discontinuance, the
Information for DECT Product
telephone company must: (1) promptly notify you of such temporary discontinuance;
(2) afford you the opportunity to correct the situation; and (3) inform you of your right
This telephone is compliant with the DECT 6.0 standard which operates in
to bring a complaint to the Commission pursuant to procedures set forth in Subpart E
the 1.92GHz to 1.93GHz frequency range.
of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities,
equipment, operations or procedures where such action is required in the operation
of its business and not inconsistent with FCC Rules and Regulations. If these changes
are expected to affect the use or performance of your telephone equipment, the
telephone company must give you adequate notice, in writing, to allow you to
maintain uninterrupted service.
Visit the GE website at: www.GE.com/phones
Thomson Inc.
101 West 103rd Street
Model 27955 Indianapolis, IN 46290-1102
00023406 (Rev. 0 Dom E/S)
© 2007 Thomson Inc.
07-41
Trademark(s) ® Registered
Printed in China Marca(s) Registrada(s)
Introduction Installing the Handset Battery
CAUTION: When using telephone equipment, there are basic NOTE: You must connect the handset battery before use.
safety instructions that should always be followed. Refer to the
CAUTION: To reduce the risk of fire or personal injury, use only
IMPORTANT SAFETY INSTRUCTIONS provided with this product
the Thomson Inc. approved Nickel-metal Hydride (Ni-MH) battery
and save them for future reference.
model 5-2734, that is compatible with this unit.
IMPORTANT: Because cordless phones operate on electricity, you
1. Locate battery which is packaged inside a plastic bag and is separate from the
should have at least one phone in your home that isn't cordless, in
handset.
case the power in your home goes out.
2. Locate the battery compartment on the back of the handset.
If you have purchased an extra handset apart from your original
3. Plug the battery pack cord into the jack inside the compartment.
purchased unit you may find a detailed description of its functions in
NOTE: To ensure proper battery installation, the connector is keyed
the User's Guide provided with your original purchased unit.
and can be inserted only one way.
If you have purchased an extra handset that is not of the same type
as your original handset you may still use the original User's Guide to
help explain the new handsets basic functions and options.
Before You Begin
Parts Checklist
Make sure your package includes the items shown here.
4. Insert the battery pack.
5. Close the battery compartment by placing the handset back cover slightly higher
than the handset and then sliding the cover up into position.
Handset Charging Cradle
1. Plug the AC power converter of the charging cradle into the electrical outlet.
Handset Charge Handset battery Battery Handset
NOTE: This power adaptor is intended to be correctly orientated in a
Cradle pack cover
vertical or floor mount position.
Installation
2. Place the handset in the charging cradle. The charge indicator turns on, verifying
Digital Security System
the battery is charging.
3. Allow the handset to charge for 14 hours prior to first use.
Your cordless phone uses a digital security system to protect against false ringing,
Registration
unauthorized access, and charges to your phone line.
INSTALLATION NOTE: Some cordless telephones operate at
A cordless handset will not operate until it is registered to the base. During the
frequencies that may cause or receive interference with nearby
registration process, keep the handset near the base. Up to 4 cordless handsets can
TVs, microwave ovens, and VCRs. To minimize or prevent such
be registered to one base.
interference, the base of the cordless telephone should not be placed
NOTE: If a handset is not registered; Not Register flashes on the
near or on top of a TV, microwave ovens, or VCR. If such interference
display and if the TALK button on the handset is pressed, it will
continues, move the cordless telephone farther away from these
display Unavailable.
appliances.
1. Make sure your phone is OFF (not in talk mode).
Certain other communications devices may also use the 1.9 GHz
2. Press the menu button to go to the main menu and use cid/vol (5or6) button to
frequency for communication, and, if not properly set, these
scroll to Registration.
devices may interfere with each other and/or your new telephone.
If you are concerned with interference, please refer to the owner's
3. Press menu button to confirm and you may program the following items: Register
manual for these devices on how to properly set channels to avoid and Remove handset.
interference. Typical devices that may use the 1.9 GHz frequency
Register
for communication include wireless audio/video senders, wireless
computer networks, multi-handset cordless telephone systems, and From the Registration Menu:
some long-range cordless telephone systems.
1. Press the cid/vol (5or6) button to scroll to the Register sub-menu.
Important Installation Guidelines
2. Press menu button to enter the menu.
3. Press and hold the page button on base for 5 seconds.
• Avoid sources of noise and heat, such as motors, fluorescent lighting,
microwave ovens, heating appliances and direct sunlight.
4. The charge indicator will flash slowly for 2 minutes which shows the base is in
registration mode.
• Avoid areas of excessive dust, moisture and low temperature.
5. If the registration is successful, the handset shows Successful and emits a
• Avoid other cordless telephones or personal computers.
confirmation tone for 3 seconds.
• Never install telephone wiring during a lightning storm.
6. If the registration fails (i.e. timeout), the handset shows No base and emits an
• Never install telephone jacks in wet locations unless the jack is specifically
error tone. Please check to see if your register operation is correct and try to
designed for wet locations.
register the handset again.
• Never touch non-insulated telephone wires or terminals, unless the telephone
line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
De-Register General Product Care
Deregistration cancels registration. During the deregistration process, keep the
To keep your unit working and looking good, follow these guidelines:
handset near the base.
• Avoid dropping the handset, as well as other rough treatment to the phone.
WARNING: It is not recommended that a handset be deregistered
• Clean the phone with a soft cloth.
unless absolutely necessary because once a handset is deregistered,
that handset's telephone features cannot be used until the handset • Never use strong cleaning agents, paint thinner, abrasive powder, alcohol, or
is re-registered. other chemical products to clean the unit. Doing so will damage the finish.
• Retain the original packaging in case you need to ship the phone at a later
From the Registration Menu:
date.
1. Press the cid/vol (5or6) button to scroll to the Remove handset sub-menu.
• Periodically clean the charge contacts on the handset and base with a clean
2. Press menu button to enter the menu. Remove handset? shows on the display.
pencil eraser.
3. Press menu button again to confirm de-registration. Causes of Poor Reception
Intercom Operation
• Aluminum siding.
The intercom feature allows you to have a conversation with another registered • Foil backing on insulation.
handset without tying up the telephone line, allowing you to still receive incoming
• Heating ducts and other metal construction that can shield radio signals.
calls.
• You 're too close to appliances such as microwaves, stoves, computers, etc.
NOTE: The function is applicable only with additional handsets.
• Atmospheric conditions, such as strong storms.
NOTE: The following procedures can ONLY be done when registered
• Base is installed in the basement or lower floor of the house.
to Model 27951 & 27950.
• Base is plugged into AC outlet with other electronic devices.
Handset to Handset Intercom Call
• Baby monitor is using the same frequency.
• Handset battery is low.
1. Make sure the originating phone is OFF (not in talk mode).
2. Press the menu button and use the cid/vol (5or6) button to scroll to Intercom. • You're out of range of the base.
Warranty Assistance
3. Press the menu button to enter the menu. INT - Number? shows on the display.
4. Use the touch-tone pad to input the number of the handset you want to page.
If trouble is experienced with this equipment, for warranty information, please contact
(For example: press 1 to page handset 1.)
customer service at 1-800-448-0329. If the equipment is causing harm to the telephone
5. The receiving handset is paged and emits a tone.
network, the telephone company may require that you disconnect the equipment until
NOTE: To cancel the page, press the TALK/END button on the the problem is resolved.
originating handset.
Any unauthorized repairs, changes or modifications not expressly approved by Thomson
8. Wait for the person at the receiving handset to press the TALK/END button. Inc. could void the user's authority to operate this product. For instructions on how to
obtain a replacement unit, refer to the warranty included in this guide or call customer
NOTE: If the receiving handset does not answer within two minutes,
service at 1-800-448-0329.
the intercom call is automatically canceled and the originating
handset displays NO ANSWER. Or refer inquiries to:
Thomson Inc.
9. When finished, press the TALK/END on either handset to deactivate the intercom.
Manager, Consumer Relations
Three-Way Conferencing
P O Box 1976
Indianapolis, IN 46206
You may have a 3-way conversation using the handset, the base and an open line.
Attach your sales receipt to this booklet for future reference or jot down the date this
1. When the phone rings, press the TALK/END button on the handset and press the
product was purchased or received as a gift. This information will be valuable if service
Speaker button on the base.
should be required during the warranty period.
2. Conference shows on the handset display. And when the conference starts, all
the 3 parties will hear conference alert tone.
Purchase date
3. When finished, press the TALK/END button (or put the handset back into the base
Name of store
cradle) and press the Speaker button again to hang up.
NOTE: If the phone system is expanded to more than one handset,
only 2 handsets with the external line or 1 handset and the base with
the external line will be allowed in a telephone line conference. When
the other handset tries to join the conference, Unavailable will be
shown with error beeps. When a handset is in use (in talk mode), the
other handset(s) will show Line in use.
Battery Safety Precautions
• Do not burn, disassemble, mutilate, or puncture. Like other batteries of this type,
toxic materials could be released which can cause injury.
• To reduce the risk of fire or personal injury, use only the Nickel-metal
Hydride (Ni-MH) battery listed in the User's Guide.
• Keep batteries out of the reach of children.
• Remove batteries if storing over 30 days.
NOTE: The RBRC seal on the battery used in your Thomson Inc. product
indicates that we are participating in a program to collect and recycle the
rechargeable battery (or batteries).
For more information go to the RBRC web site at www.rbrc.org
or call 1-800-8-BATTERY or contact a local recycling center.
Limited Warranty
What your warranty covers:
• Defects in materials or workmanship.
For how long after your purchase:
• One year, from date of purchase.
(The warranty period for rental units begins with the first rental or 45 days from date
of shipment to the rental firm, whichever comes first.)
What we will do:
• Provide you with a new or, at our option, a refurbished unit. The exchange unit is
under warranty for the remainder of the original product's warranty period.
How you get service:
• Properly pack your unit. Include any cables, etc., which were originally provided with
the product. We recommend using the original carton and packing materials.
• "Proof of purchase in the form of a bill of sale or receipted invoice which is evidence
that the product is within the warranty period, must be presented to obtain warranty
service." For rental firms, proof of first rental is also required. Also print your name
and address and a description of the defect. Send via standard UPS or its equivalent
to:
Thomson Inc.
11721 B Alameda Ave.
Socorro, Texas 79927
• Insure your shipment for loss or damage. Thomson Inc. accepts no liability in case of
damage or loss.
• A new or refurbished unit will be shipped to you freight prepaid.
What your warranty does not cover:
• Customer instruction. (Your Owner's Manual provides information regarding
operating instructions and user controls. Any additional information, should be
obtained from your dealer.)
• Installation and setup service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modified or incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.
Product Registration:
• Please complete and mail the Product Registration Card packed with your unit. It will
make it easier to contact you should it ever be necessary. The return of the card is
not required for warranty coverage.
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS
PRODUCT. ALL OTHER WARRANTIES, ExPRESS OR IMPLIED (INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE
HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION GIVEN BY THOMSON
INC., ITS AGENTS, OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY
INCREASE THE SCOPE OF THIS WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE
ExCLUSIVE REMEDY OF THE CONSUMER. THOMSON INC. SHALL NOT BE LIABLE
FOR INCIDENTAL OR CONSEqUENTIAL DAMAGES RESULTING FROM THE USE OF
THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY ExPRESS OR IMPLIED
WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED
WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA. ExCEPT
TO THE ExTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS
LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
How state law relates to this warranty:
• Some states do not allow the exclusion nor limitation of incidental or consequential
damages, or limitations on how long an implied warranty lasts so the above
limitations or exclusions may not apply to you.
• This warranty gives you specific legal rights, and you also may have other rights that
vary from state to state.
If you purchased your product outside the USA:
• This warranty does not apply. Contact your dealer for warranty information.