GE 16272270 User Manual

21002
Notes
Extra Handset and Recharge Cradle
• This equipment may not be used on coin service provided by the
with Call-Waiting Caller ID for Use with
telephone company.
Models 21025 and 21095
• Party lines are subject to state tariffs, and therefore, you may not
User's Guide
be able to use your own telephone equipment if you are on a
party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent
disconnection of your telephone from your line.
• If your home has specially wired alarm equipment connected to
the telephone line, ensure the installation of this product does
not disable your alarm equipment. If you have questions about
what will disable alarm equipment, consult your telephone
company or a qualified installer.
2 Rights of the Telephone Company
Should your equipment cause trouble on your line which may
harm the telephone network, the telephone company shall, where
practicable, notify you that temporary discontinuance of service
may be required. Where prior notice is not practicable and the
circumstances warrant such action, the telephone company may
temporarily discontinue service immediately. In case of such
temporary discontinuance, the telephone company must: (1)
promptly notify you of such temporary discontinuance; (2) afford
you the opportunity to correct the situation; and (3) inform you of
your right to bring a complaint to the Commission pursuant to
procedures set forth in Subpart E of Part 68, FCC Rules and
Regulations.
The telephone company may make changes in its
communications facilities, equipment, operations or procedures
We bring good things to life. where such action is required in the operation of its business and
not inconsistent with FCC Rules and Regulations. If these changes
are expected to affect the use or performance of your telephone
E A I
QUIPMENT PPROVAL NFORMATION equipment, the telephone company must give you adequate
notice, in writing, to allow you to maintain uninterrupted service.
Your telephone equipment is approved for connection to the Public
FCC RF E
Switched Telephone Network and is in compliance with parts 15 and XPOSURE
68, FCC Rules and Regulations and the Technical Requirements for
For body worn operation, this phone has been tested and meets the
Telephone Terminal Equipment published by ACTA.
FCC RF exposure guidelines when used with the belt clip supplied
1 Notification to the Local Telephone Company
with this product. Use of other accessories may not ensure
On the bottom of this equipment is a label indicating, among compliance with FCC RF exposure guidelines.
other information, the US number and Ringer Equivalence
I I
NTERFERENCE NFORMATION
Number (REN) for the equipment. You must, upon request,
provide this information to your telephone company.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
The REN is useful in determining the number of devices you may
connect to your telephone line and still have all of these devices cause harmful interference; and (2) This device must accept any
ring when your telephone number is called. In most (but not all) interference received, including interference that may cause
areas, the sum of the RENs of all devices connected to one line undesired operation.
should not exceed 5. To be certain of the number of devices you
This equipment has been tested and found to comply with the limits
may connect to your line as determined by the REN, you should
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
contact your local telephone company.
These limits are designed to provide reasonable protection against
A plug and jack used to connect this equipment to the premises harmful interference in a residential installation.
wiring and telephone network must comply with the applicable
This equipment generates, uses, and can radiate radio frequency
FCC Part 68 rules and requirements adopted by the ACTA. A
energy and, if not installed and used in accordance with the
compliant telephone cord and modular plug is provided with this
instructions, may cause harmful interference to radio
product. It is designed to be connected to a compatible modular
communications. However, there is no guarantee that interference
jack that is also compliant. See installation instructions for
will not occur in a particular installation.
details.
ATLINKS USA, Inc.
101 West 103rd Street
Model 21002 Indianapolis, IN 46290
16272270 (Rev. 0 DOM E) © 2003 ATLINKS USA, Inc.
03-34 Trademark(s) ® Registered
Printed in China Marca(s) Registrada(s)
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna
for radio or television that is "receiving" the interference).
• Reorient or relocate and increase the separation between the
telecommunications equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a
circuit different from that to which the receiving antenna is
connected.
If these measures do not eliminate the interference, please consult
your dealer or an experienced radio/television technician for
additional suggestions. Also, the Federal Communications
Commission has prepared a helpful booklet, "How To Identify and
Resolve Radio/TV Interference Problems. " This booklet is available
from the U.S. Government Printing Office, Washington, D.C. 20402.
Please specify stock number 004-000-00345-4 when ordering copies.
H A C
EARING ID OMPATIBILITY
This telephone system meets FCC standards for Hearing Aid
Compatibility.
US NUMBER IS LOCATED ON THE CABINET BOTTOM
CAUTION:
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING CAUTION: TO REDUCE THE
FLASH AND ARROW RISK OF ELECTRIC SHOCK, DO
WARNING: TO
HEAD WITHIN THE NOT REMOVE COVER (OR
PREVENT FIRE OR
TRIANGLE IS A BACK). NO USER
WARNING SIGN SERVICEABLE PARTS INSIDE.
ELECTRICAL SHOCK
ALERTING YOU OF REFER SERVICING TO
HAZARD, DO NOT "DANGEROUS QUALIFIED SERVICE
VOLTAGE" INSIDE PERSONNEL.
EXPOSE THIS
THE PRODUCT.
PRODUCT TO RAIN
R
EQUIREMENTS SEE MARKING ON BOTTOM / BACK OF PRODUCT
OR MOISTURE.
I
NTRODUCTION
CAUTION: When using telephone equipment, there are
basic safety instructions that should always be followed. Refer
to the IMPORTANT SAFETY INSTRUCTIONS provided with
this product and save them for future reference.
Congratulations on purchasing this extra GE cordless handset with Call
Waiting Caller ID. This telephone has been designed to be simple to
use, however, you can reach its full potential more quickly by taking a
few minutes to read this instruction book. This telephone is a
multifunction product for use with Call Waiting and Caller ID services
available from your local telephone company.
Your Call Waiting Caller ID phone allows you to:
• view the name and telephone number of a caller while you are on
the phone (Call Waiting Caller ID).
• identify callers before you answer the phone.
• view the time and date of each incoming call.
• record up to 40 Caller ID messages sequentially in each handset
and the base.
• know who called while you are on the other line or when you
were away.
• screen unwanted calls, eliminate harassment from annoying
calls, or to get prepared before answering a call.
B
EFORE
IMPORTANT: Because cordless phones operate on electricity,
you should have at least one phone in your home that isn't
cordless, in case the power in your home goes out. P
ARTS
Make sure your package includes the items shown here.
IMPORTANT: In order to use all of the features of this
telephone, you must subscribe to two separate services available
from your local telephone company: the standard Name/
Number Caller ID Service to know who is calling when the
phone rings and Call Waiting Caller ID Service to know who is
program mute mem
calling while you are on the phone. talk format
conference
redial page
int
1 2
review
4 ghi 5
7 pqrs 8
INSTALLATION NOTE: Some cordless telephones operate at
* tone 0
erase
frequencies that may cause interference to nearby TVs, microwave
ovens, and VCRs. To minimize or prevent such interference, the
Handset
base of the cordless telephone should not be placed near or on top
of a TV, microwave ovens, or VCR. If such interference continues, I
NSTALLING THE
move the cordless telephone farther away from these appliances.
Certain other communications devices may also use the 2.4 GHz
frequency for communication, and, if not properly set, these
devices may interfere with each other and/or your new telephone.
Typical devices that may use the 2.4 GHz frequency for
communication include wireless audio/video senders, wireless
• Never install telephone wiring during a lightning storm.
computer networks, multi-handset cordless telephone systems, and
• Never install telephone jacks in wet locations unless the jack is
some long-range cordless telephone systems.
specifically designed for wet locations.
H C C L
ANDSET AND HARGE RADLE AYOUT • Never touch non-insulated telephone wires or terminals, unless
the telephone line has been disconnected at the network
interface.
mute/program button
Display
• Use caution when installing or modifying telephone lines.
THE EXCLAMATION
mem (memory) button • Temporarily disconnect any equipment connected to the phone
POINT WITHIN THE
TRIANGLE IS A
format/conference button such as faxes, other phones, or modems.
WARNING SIGN
ALERTING YOU OF
exit/answerer button
IMPORTANT
I
INSTRUCTIONS MPORTANT
ACCOMPANYING talk/callback button
THE PRODUCT. mute mem exit
• Install telephone near an electrical power outlet.
CID/vol buttons
+
talk format
• Avoid sources of noise, such as a window by a busy street, and
conference -
redial button
redial flash
page ringer
electrical noise, such motors, microwave ovens, and fluorescent
int delete flash/delete button
1 2 abc 3 def
review play/stop skip lighting.
4 5 6
ghi jkl mno
page/int button
7 8 tuv 9 wxyz
pqrs ringer button
• Avoid heat sources, such as heating air ducts, heating appliances,
* tone 0 oper # pause
erase radiators, and direct sunlight.
review button
skip button
• Avoid areas of excessive moisture or extremely low temperature.
• Avoid dusty locations.
play/stop button
# pause button
• Avoid other cordless telephones or personal computers.
* tone button erase button
C
ONNECTING THE
1. Plug the charge cradle power supply into an electrical outlet.
AC power supply
2. Place the handset in charge cradle. The charge indicators turn on
to indicate the batteries are charging.
charge indicator
I
NSTALLING THE
NOTE: You must connect the handset battery before use.
charge
1. Push down on the top of the battery compartment cover (located
on the back of each handset) and remove the cover.
2. Lift the battery pack and connect it's plug to the jack inside the
compartment.
NOTE: It is important to maintain the polarity (black and red
wires) to the jack inside the compartment as shown in the
illustration.
Y B 3. Close the battery compartment by pushing the cover up until it
OU EGIN
snaps into place.
4. Place the handset in the charging cradle.
C
HECKLIST
5. Allow the handset to charge for 16 hours prior to registration to
models 21025 or 21095. If you don't properly charge the phone,
battery performance is compromised.
exit answerer
+
-
ringer flash
delete
abc 3 def
play/stop skip
jkl 6 mno
tuv 9 wxyz
oper # pause charge
Belt Clip Handset battery pack Handset charge cradle PRESS DOWN
FIRMLY
P
HONE
IMPORTANT: Make sure the extra handset is registered IMPORTANT: After you place the handset in the cradle the
on GE Model 21025 and Model 21095 before use. Refer display shows "SEARCHING..." and " HANDSET NEEDS
to the GE 21025 or 21095 instruction book for detailed REGISTRATION" alternately. Wait until the handset charges
installation and operation information. properly, then register the handset to the base before use.
P T
ROGRAMMING THE
H R
ANDSET EGISTRATION
CAUTION: Make sure the extra handset is registered
before use.
NOTE: This extra handset is only available for 21025 and
21095 series.
During the registration process, keep your handset near the base.
When your handset shows the following:
I G
NSTALLATION UIDELINES
HANDSET NEEDS
REGISTRATION
1. Press the mute /program button until REGISTRATION 1YES 2NO
shows in the display. The default setting is NO .
) button to scroll to 1YES or 2NO , or use
2. Press the cid/vol ( or
the touch tone pad on your handset to enter your selection.
AC (E ) P 3. Press the mute/program button and HOLD BASE PAGE WAIT FOR
LECTRICAL OWER
BEEP shows in the display.
HOLD BASE PAGE
H B
ANDSET ATTERY
WAIT FOR BEEP
4. Press and hold the page/int button on the base of Model 21095 or
the page button on the base of Model 21025 until you hear a long
beep and the handset displays HANDSET # REGISTERED
displays, and you will hear a confirmation tone.
HANDSET #
REGISTERED
H N
ANDSET AME
BATTERY 1. Use the touch-tone keypad to enter the name (up to 15 characters).
More than one letter is stored in each of the number keys. For
BLACK WIRE
example, to enter the name Bill Smith, press the 2 key twice for the
letter B. Briefly pause and the cursor moves to the next field. Press
the 4 key 3 times for the letter I. Briefly pause and the cursor moves
to the next field. Press the 5 key 3 times for the second letter L.
RED WIRE
Briefly pause and the cursor moves to the next field. Press the 5 key
3 times for the second letter L, press 1 key to add a space. Press the
7 key 4 times for the letter S. Briefly pause and the cursor moves to
the next field. Press the 6 key once for the letter M. Briefly pause and
the cursor moves to the next field. Press the 4 key 3 times for the
letter I. Briefly pause and the cursor moves to the next field. Press
the 8 key for the letter T. Briefly pause and the cursor moves to the
ELEPHONE next field. Press the 4 key twice for the letter H.
NOTE: If you make a mistake press the flash/delete button to
backspace and erase the wrong character(s).
NOTE: Press mute/program once to skip this step and exit to
standby screen.
NOTE: Press the exit/answerer button on the handset once to
keep the previous setting and return to standby mode.
2. Press the mute/program button to save the name and return to
main menu. You will hear a confirmation tone.
HANDSET NAME
H D -
ANDSET E REGISTRATION
Deregistration cancels a handset's registration. If you do not know a
handset's name, you should deregister the handset according to the
steps below. During the de-registration process, keep the handset
near the base.
WARNING: It is not recommended that a handset be de-
registered unless absolutely necessary because once a
handset is de-registered, that handset's telephone features
cannot be used until the handset is re-registered.
1. Make sure your handset is in menu mode and make sure your
phone is OFF (not in talk mode).
2. Press the mute/program button until DEREGISTRATION 1YES
2NO shows in the display.
HANDSET NEEDS
REGISTRATION