Safety warnings for user Maintenance and care Metal grease filter Opening the metal grease filter Carbon filter Changing the light bulb Cleaning Accessories Something not working Service & Spare Parts Printed on recycled paper. AEG – putting words into action.
(available as an accessory). You will need original AEG activated carbon filters for the filtered function (see Accessories). The air is forced out through a hose fitted to the top of the hood A.
The air is filtered through an activated carbon filter and passed back into the kitchen through the top outlet duct grids. You will need an original AEG KF 825 activated carbon filter for the filtering function. (See Accessories). Fix the deflector with two screws Ø3,5x6,5. Fig. 2.
Electrical connection for the UK Appliances with 2 wires WARNING: DOUBLE INSULATED - DO NOT EARTH The appliance must be connected to fixed wiring with a double pole switched fused spur outlet with or without pilot lamp. We strongly recommend the appliance to be connected only by a qualified electrician who is a member of the NICEIC who will com- ply with the IEE and any local regulations.
Technical Details Dimensions (825 D): Height x Width x Depht (in cm) 84-117 x 59,9 x 51.5 Dimensions (8259 D): Height x Width x Depht (in cm) 84-117 x 89,9 x 51.5 Weight (825 D): Net: 10,7 kg Gross: 16,2 kg...
Installation Safety warnings for kitchen unit installer When used as an extractor unit, the hood must be fitted with a 120mm diameter hose. If the fumes must be forced out through the wall, you must obtain a MKZ sizable wall exhaust pipe (with external exhaust and air intake), E-Nr.- 610 899 004 (Ø...
Page 8
Regulations on fuel-burning systems specify a maximum depression of 0.04 bar in such rooms. Hoods can only be used safely with appliances connected to a chimney if the room and/or flat (air/environment combination) is ventilated from outside using a suitable ventilation hole approxi- mately 500-600 cm to avoid the possibility of a depression being created during operation of the hood.
Installation - Fig. 3 Put the template onto the wall (1) and drill two Ø12mm holes (2). Fit two hooks (3) on the drilled holes. Hang the hood on the hooks and adjust the position of the hood using the two screws on the bottom of the hooks (5). Remove the metal filters (4) and mark two points (6).
Hood Operation The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on for approximately 15 minutes after you have finished, thus ensuring all cooking odours are eliminated.
Safety warnings for user Never leave a cooking hob or ring on without a pot or pan on top of it, to avoid the possibility of excess heat damaging the unit. Gas, oil or coal cooker flames in particular should never be left uncovered.
Maintenance and care The hood must always be disconnected from the mains power supply before beginning any maintenance work. Metal grease filter The purpose of the grease filters is to aspirate grease particles which form during cooking and it must always be used, either in extraction or recirculation mode.
The activated carbon filter should only be used if you want to use the hood in the recirculation. To do this you will need an original AEG activated carbon filter (see special accessories). This filter cannot be cleaned or reused.
Replace the old light bulb with a new light bulb (40 W max.). Fit the lamp cover on its seat. If the light does not come on, make sure the bulb has been screwed in correctly before contacting AEG Service Force.. Fig. 6...
Cleaning Warning: always disconnect the hood from the mains power supply before cleaning it. Never insert pointed objects in the motor’s protective grid. Wash the outside surfaces using a mild detergent solution. Never use caustic detergents or abrasive brushes or powders. Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents.
Something not working If your cooker hood fails to work properly please carry out the following checks. Sympton Solution The cooker hood will not start... The hood is connected to the electricity supply. Check that the fan speed control is set to 1, 2 or 3.
(F-Nr) (This information can be found on the rating plate). Date of purchase. Customer Care For general enquiries regarding your AEG appliance, or further information on AEG products please contact our customer care department. Customer Care Department AEG Domestic Appliances Limited...