Electrolux ICON appliances Design Manual page 157

30" Combination Installation
For Built-In Microwave / Single Wall Oven
For detailed product dimensions
and installation specifications, refer
to model-specific product page and
installation guide on web
30" Built-In
Microwave Cutout
For models:
E30MO75HPS
2"
E30MO75HSS
(visible
gap)*
30" Electric Single
Wall Oven Cutout
For models:
E30EW75GPS
E30EW75GSS
* Minimum 2 / "
1
8
clearance required
from bottom of
Built-In Microwave
cutout to top edge of
Wall Oven's faceplate,
leaving a 2" visible
gap between both
product faceplates.
** Critical dimension –
MUST be applied
Installation Specifications
30" Combination Installation Specifications
• Always consult local and national electric codes. (Refer
to product-specific electrical specifications on this page.)
• Minimum 24" deep cutout dimension is critical for proper
combination install ation, to ensure that each built-in
product's faceplate will fit flush against cabinet front.
• Bases must be level and cabinet front must be square.
• Minimum 4-1/2" required distance from bottom of
Wall Oven cutout to floor, 31" suggested.
• Respect critical dimensions as noted for proper
installation of built-In products.
• Minimum 23-1/4" clearance needed for Wall Oven
door depth when open.
24" min.
4"
21" min.
21 / " max.
1
2 28 / " min.
1
2
29" max.
28 / "min.
1
28 / " min.
1
2
2
29" max.
28 / "max.
7
8
31"
suggested
distance
4 / "
1
2
min.
required
30" Built-In Convection Microwave Specifications
• Product Weight –
(E30MO75HPS / E30MO75HSS) 84 Lbs.
• Voltage Rating – 120V / 60 Hz / 15 Amps
• Connected Load (kW Rating) @ 120 Volts = 1.6 kW
(For use on adequately wired 120V, dedicated circuit
having 2-wire service with a separate ground wire.
Appliance must be grounded for safe operation.)
• Amps @ 120 Volts = 13.7 Amps
• Full oven base of solid plywood or similar material
required, capable of supporting 150 Lbs.
• Minimum 2-1/8" clearance required from bottom of Built-In
Microwave cutout to top edge of Wall Oven's faceplate,
leaving a 2" visible gap between both product faceplates.
30" Electric Single Wall Oven Specifications
• Product Weights –
(E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
• Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208
Volt, 60 Hertz AC only electrical supply with ground
required on separate circuit fused on both sides of line.
• Connected Load (kW Rating) @ 240 / 208 Volts =
4.0 / 3.0 kW
• Amps @ 240 / 208 Volts = 16.6 / 14.4 Amps
• Full oven base of solid plywood or similar material
required, capable of supporting 200 Lbs.
30 1 / " min.
8
120V/60Hz
grounded electrical
outlet should NOT
be located within
shaded area
6"
Full plywood base
required to support
18" 150 lbs.
C L
4"x 4" opening
to route armored
cable
24"min.**
(critical
dimension)
Full base required
to support 200 lbs.
3" max.
2" min.
Electrical junction
box location
Bottom cutout
edge must be
finish cut
e l e c t ro l u x i c o n . c o m
planning
information
For models:
Built-In
Microwave
E30MO75HPS
E30MO75HSS
Single Wall Oven
E30EW75GPS
E30EW75GSS
Note: For planning
purposes only. Refer
to Product Installation
Guide on the web at
electroluxicon.com for
detailed instructions.
Specifications subject
to change.
157