Network Setup Troubleshooting This manual describes troubleshooting tips for problems you may encounter when The Another access point with the same SSID exists is displayed during setup setting up. The New port could not be created is displayed during setup The Set Printer IP Address screen is displayed during setup The Enter Password screen is displayed during setup •...
If the firewall function of your security software is turned on, a message may appear warning that transmission among clients associated to it. If such feature is enabled, disable this feature while Canon software is attempting to access the network. If the warning message appears, set the using the machine.
If the access point is configured to use access control, register the IP address or the MAC address of the machine or disable the access control. Using 64 bit key length, when the string “canon” is entered, an access point generates the following codes.
The Access Points screen is displayed during setup (continued) The following screen is displayed during setup (C) Configuration The detailed settings dialog box is displayed. The network password (WEP) or the network key The Access Points screen is displayed during setup (WPA/WPA2) selected in Encryption Method can be confirmed and changed.
The Printer could not be connected to the specified access point is displayed The Set Printer IP Address screen is displayed during setup (continued) during setup (C) IP Address/Subnet Mask/Default Gateway This message is displayed when the machine could not connect to the target access point. Enter each value to specify a fixed IP address when Use next IP Address is selected.
Make sure that the computer is communicating with the network properly, then try again. the Canon IJ Network Tool, refer to “Using the Card Slot over a Network” in “About Network Communication” in “Appendix” of the on-screen manual: Advanced Guide. To •...
If you have changed the connection method via Change WLAN/LAN in the machine’s LAN and try the network setup of the Card Slot again using the Canon IJ Network Tool. setting, you need to setup the machine again. To do so, follow the procedures in “Install the Software”...
Make sure that Yes is selected and press the OK button. Restoring the Machine to the Factory Settings Initializing using the machine’s Operation Panel Follow these steps to restore the machine’s network settings to factory defaults. Confirm that the right screen appears. After a while, the LAN settings screen returns.
Specifications MX860 series General Specifications Copy Specifications Multiple copy Max 99 pages Printing resolution 9600 (horizontal)* x 2400 (vertical) (dpi) * Ink droplets can be placed with a pitch of 1/9600 inch at minimum. Intensity 9 positions, Auto intensity (AE copy) adjustment Interface USB Port:...
Page 11
300 MHz processor Intel processor, PowerPC G5, PowerPC G4, speed (Based on ITU-T No.1 chart for US specifications and Canon FAX Standard chart No.1 for others, both in 128 MB PowerPC G3 standard mode or Canon FAX Standard chart No.1, standard mode.) 256 MB Color: Approx.
Page 12
Solución de problemas de configuración de red En este manual se ofrecen consejos para la solución de los problemas que pueden Aparece el mensaje Ya existe otro punto de acceso con el mismo SSID (Another access point with the same SSID exists) durante la configuración pág.
Page 13
Si la función de cortafuegos del software de seguridad está activada, es posible que aparezca un usar el dispositivo. mensaje advirtiendo de que el software de Canon está intentado acceder a la red. Si aparece el mensaje de advertencia, ajuste el software de seguridad para que permita siempre el acceso.
Page 14
Si el punto de acceso está configurado para utilizar el control de accesos, registre la dirección IP o la Ejemplo: dirección MAC del equipo o desactive el control de accesos. cuando se utiliza una clave con una longitud de 64 bits, si se introduce la cadena “canon”, un punto de acceso genera los códigos siguientes: •...
Page 15
Aparece la pantalla Puntos de acceso (Access Points) durante la configuración Aparece la pantalla siguiente durante la configuración (continuación) (C) Configuración (Configuration) Aparece la pantalla Puntos de acceso (Access Points) durante la configuración Se muestra el cuadro de diálogo con la configuración detallada. Se puede comprobar y modificar la contraseña de red (WEP) o la clave de red (WPA/WPA2) seleccionada en Método de codificación La pantalla Puntos de acceso se muestra cuando: (Encryption Method).
Aparece el mensaje No se puede conectar la impresora al punto de acceso Aparece el cuadro de diálogo Establecer dirección IP de impresora (Set Printer especificado (Printer could not be connected to the specified access point) IP Address) durante la configuración (continuación) durante la configuración (C) Dirección IP/Máscara de subred/Puerta de enlace predeterminada (IP Address/Subnet Mask/ Default Gateway)
Para obtener más información sobre el software de para tarjetas mediante Canon IJ Network Tool, consulte el apartado “Uso de la ranura para tarjetas seguridad, consulte el manual de instrucciones o póngase en contacto con el fabricante.
(Getting Started). para tarjetas utilizando Canon IJ Network Tool. 5.12 Aparece la pantalla Error de tiempo de espera (Timeout error) durante la Se ha olvidado la contraseña de administrador del equipo...
Asegúrese de que se ha seleccionado Sí (Yes) Restauración de la configuración de fábrica del equipo y pulse el botón OK. Inicialización con el panel de control del equipo Siga estos pasos para restaurar la configuración de red de fábrica del equipo. Compruebe que aparece la pantalla que se muestra a la derecha.
Page 20
Especificaciones MX860 series Especificaciones generales Especificaciones de copia Número de copias 99 páginas como máximo Resolución de 9600 (horizontal)* x 2400 (vertical) impresión (ppp) * Las gotitas de tinta se pueden administrar con un pitch mínimo de 1/9600 pulgadas. Ajuste de 9 posiciones, intensidad automática (copia AE) intensidad Interfaz...
Page 21
(Basado en el gráfico ITU-T N.º 1 para las especificaciones de EE UU y el gráfico estándar Canon FAX 128 MB PowerPC G3 N.º 1 para los demás, ambos en el modo estándar o en el gráfico estándar Canon FAX N.º 1, modo estándar.) 256 MB Color: 1 minuto/página aprox. a 33,6 Kbps, ECM-JPEG, transmitiendo desde la memoria (Basado en la HOJA DE COMPROBACIÓN DE FAX EN COLOR Canon.)