Hitachi L300P Series Instruction Manual Supplement page 9

L300P Supplement
Function Mode
Code Function name
st
A061 1 frequency upper limiter
nd
A261 2 frequency upper limiter
st
A062 1 frequency lower limiter
nd
A262 2 frequency lower limiter
A063 Jump frequency1
A064 Jump frequency band1
A065 Jump frequency2
A066 Jump frequency band2
A067 Jump frequency3
A068 Jump frequency band3
A069 Acceleration stop frequency
A070 Acceleration stop time
A071 PID selection
A072 PID P gain
A073 PID I gain
A074 PID D gain
A075 PID scale
A076 PID feedback selection
A081 AVR selection
A082 Motor voltage selection
A085 Operation mode selection
Energy-saving response･
A086
accuracy adjustment
A092 Acceleration time2
A292 Acceleration time2(2
A093 Deceleration time2
A293 Deceleration time2(2
nd
A094 2 stage adjustable selection
nd
2 stage adjustable
A294
nd
selection(2 motor)
nd
A095 2 acceleration frequency
nd
2 acceleration
A295
nd
frequency(2 motor)
nd
A096 2 deceleration frequency
nd
2 deceleration frequency
A296
nd
(2 motor)
Acceleration pattern selection
A097
Deceleration pattern selection
A098
A101 OI start
A102 OI end
A103 OI start rate
A104 OI end rate
A105 OI start selection
A111 O2 start
A112 O2 end
A113 O2 start rate
A114 O2 end rate
A131 Acceleration curve constant
A132 Deceleration curve constant
b001 Retry selection
Allowable under-voltage power
b002
failure time
b003 Retry wait time
Instantaneous power failure/
b004
under-voltage trip during stop
Instantaneous power failure/
b005 under-voltage retry time
selection
b006 Open-phase selection
b007 Frequency setting to match
st
0.00, 1 frequency lower limiter-maximum frequency(Hz)
0.00 ， nd
2 frequency lower limiter-2
frequency(Hz)
0.00，start frequency-maximum frequency(Hz)
0.00， start frequency-2
00(feedback : OI)/01(feedback : O)
00(ON always)/01(OFF always)/02(OFF on decelerating)
200/215/220/230/240，380/400/415/440/460/480(V)
00(normal operation)/01(energy-saving operation)
0.01-99.99/100.0-999.9/1000.-3600.(s)
nd
motor) 0.01-99.99/100.0-999.9/1000.-3600.(s)
0.01-99.99/100.0-999.9/1000.-3600.(s)
nd
motor) 0.01-99.99/100.0-999.9/1000.-3600.(s)
00(change with 2CH terminal)/01(change with setting)
00(change with 2CH terminal)/01(change with setting)
00(straight line)/01(S-curve)/02(U-curve)/
03(reverse U-curve)
00(straight line)/01(S-curve)/02(U-curve)/
03(reverse U-curve)
00(external start frequency)/01(0Hz)
-400.--100./-99.9-0.00-99.9/100.-400.(Hz)
-400.--100./-99.9-0.00-99.9/100.-400.(Hz)
01(small swelling)-10(large swelling)
01(small swelling-10(large swelling)
00(trip)/01(Ohz start)/02(start after equal frequency)/
03(trip after equaling frequency and deceleration stop)
02(invalid during stop and deceleration by stop command)
Setting range
nd
setting maximum
nd
setting maximum frequency(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-10.00(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-10.00(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-10.00(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-60.0(s)
00(invalid)/01(valid)
0.2-5.0
0.0-3600.(s)
0.00-100.0(s)
0.01-99.99(%)
0.0-100.0(s)
0.00-99.99/100.0-400.0(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-99.99/100.0-400.0(Hz)
0.-100. (%)
0.-100. (%)
-100. - 100. (%)
-100. - 100. (%)
0.3-1.0(s)
0.3-100.(s)
00(invalid/01(valid)/
00(16 times)/01(free)
00(invalid)/01(valid)
0.00-99.99/100.0-400.0(Hz)
7
Explanation of functions
LBRM/HFBM LFU/HFU
Initial Data Initial data
60.00
60.00
15.00
15.00
0.00
0.50
0.00
0.50
0.00
0.50
0.00
0.0
00
1.0
1.0
0.00
1.00
00
00
230/460
00
50.0
60.00
60.00
90.00
90.00
00
00
0.00
0.00
0.00
0.00
00
00
0.00
60.00
20.
100.
01
-60.00
60.00
-100.
100.
02
02
02
1.0
1.0
00
00
00
0.00
0.00
0.00
0.00
0.00
0.00
0.50
0.00
0.50
0.00
0.50
0.00
0.0
00
1.0
1.0
0.00
1.00
00
00
230/460
00
50.0
15.00
15.00
15.00
15.00
00
00
0.00
0.00
0.00
0.00
00
00
0.00
0.00
20.
100.
01
0.00
0.00
-100.
100.
02
02
00
1.0
1.0
00
00
00
0.00