Table of Contents
Advertisement
Audible signals
Audible signals have been introduced to help indicate which
operations the dishwasher is performing:
"Setting of the water softener"
"End of programme"
"Something not working with the machine"
Deactivation/activation of the audible
signals
(The dishwasher must be switched off)
1. Press the On/Off push button. The indicator lights of the
programme selection push buttons will illuminate and in the
digital display are visible 2 horizontal lines (--) (setting
mode).
2. Press simultaneously function push buttons 2 and 3, the
indicator lights of the function push buttons 1, 2 and 3 start
flashing.
Prior to using for the first time
Before using your dishwasher for the first time:
1. Ensure that the electrical and water connections comply
with the installation instructions
2. Remove all packaging from inside the appliance
3. Set the water softener
4. Pour 1 litre of water inside the salt container and then fill
with salt
5. Fill the rinse aid dispenser
6. Run a "Rinse and Hold" programme
Setting the water softener
The dishwasher is equipped with a water softener designed to
remove minerals and salts from the water supply, which would
have a detrimental or adverse effect on the operation of the
appliance.
The higher the content of these salts, the harder your water is.
Water hardness is measured in equivalent scales, German
degrees, French degrees and PPM (parts per Million).
The softener should be adjusted according to the hardness of
the water in your area. Your local Water Authority can advise
you on the hardness of the water in your area.
Water hardness
°dH
°TH
(german degrees)
(french degrees)
51 - 70
91 - 125
43 - 50
76 - 90
65 - 75
37 - 42
29 - 36
51 - 64
23 - 28
40 - 50
33 - 39
19 - 22
15 - 18
26 - 32
11 - 14
19 - 25
7 - 18
4 - 10
< 4
< 7
Adjusting the water
hardness setting
PPM
manually
(parts per million)
901 - 1250
2
751- 900
2
641 - 750
2
501 - 640
2
391 - 500
2
321 - 390
2
251 - 320
1
181 - 250
1
70 - 180
1
< 70
1
3. Press the function push button 3, the indicator lights of
function push buttons 1 and 2 turn off while the indicator
light of the push button 3 goes on flashing, the digital
display indicates the current setting.
Audible signals activated
Audible signals deactivated (factory set)
4. To change the current setting, press again the function
push button 3, the digital display will indicate the new
setting.
5. To memorise the operation, switch off the dishwasher by
pressing the On/Off push button or wait about 60 seconds
after which the dishwasher will automatically return to
setting mode.
The water softener must be set in both ways: manually, using
the water hardness switch and electronically, using the function
push buttons on the control panel.
If your water is level 1 it is already soft and therefore there
is no need to use salt.
Setting manually
The dishwasher is factory set at position 2.
1. Open the dishwasher door.
2. Remove the lower basket from the dishwasher.
3. Turn the water hardness
switch to position 1 or 2
(see table).
4. Replace the lower basket.
Level indicated
in the
digital display
electronically
level 10
level 9
level 8
level 7
level 6
level 5
level 4
level 3
level 2
level 1
24
AA07
Number of
Use
audible
of salt
signals
10
yes
9
yes
8
yes
7
yes
6
yes
5
yes
4
yes
3
yes
2
yes
1
no
Advertisement
Table of Contents
