Related Manuals for Panasonic AJ-FX216
Summary of Contents for Panasonic AJ-FX216
- Page 1 Video Multiplexer WJ-FS216 Before attempting to connect or operate this product, please read these instructions completely...
- Page 2 If you lose the fuse cover the plug must not be used until a replacement TO REDUCE THE RISK OF ELECTRIC SHOCK, cover is obtained. DO NOT REMOVE COVER (OR BACK), NO USER A replacement fuse cover can be purchased from your local Panasonic SERVICEABLE PARTS INSIDE. Dealer. REFER SERVICING TO QUALIFIED SERVICE IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCK- PERSONNEL.
-
Page 4: Table Of Contents
CONTENTS PREFACE ....................................2 FEATURES ....................................2 IMPORTANT NOTICES ................................2 PRECAUTIONS ..................................2 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ....................3 RACK MOUNTING .................................. 6 SETTING UP THE MENU ................................ 7 A. Setting up MENU 1 OF 3 in MULTIPLEX mode ....................... 8 B. -
Page 5: Preface
PREFACE IMPORTANT NOTICES • While playing back the picture of the time lapse The WJ-FS216 Video Multiplexer is designed to pick up VTR with linear mode, the picture of another chan- the field signals from video cameras and record the nel may be reproduced and break in. -
Page 6: Major Operating Controls And Their Functions
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS Panasonic CAMERA/VTR MODE ALARM ZOOM MENU POWER SELECT SEQENCE MULTI SCREEN CAMERA ALARMRESET QUAD SHIFT SELECT Digital Video MultiplexerWJ-FS STILL ON CAMERA CAMERA SW IN PLAY IN REC OUT MONITOR OUT CAMERA SIGNAL ALARM/REMOTE 1. - Page 7 Button No.15 (SET) 5. Camera Selection Button (1...16, This button is used as the SET button in setting pro- CAMERA/VTR, , –, +, SET, STILL cedures. When the MODE SELECT/CAMERA SELECT switch Button No.16 (STILL ON) is in CAMERA SELECT position, these buttons can This button is used to pause the picture on the be used to select the desired camera.
- Page 8 13. Recording Output Connector (REC OUT) This connector supplies the recording signal for the time lapse VTR. Caution: In MULTIPLEX mode, the unit adds codes to video signals during vertical blanking while they are recorded on the VTR. This is the reason why video signals with a certain code are not recordable during vertical blanking.
-
Page 9: Rack Mounting
RACK MOUNTING To install the WJ-FS216 Video Multiplexer in an EIA 19- 4. Install the unit in the rack with four screws (to be inch rack, use the rack mounting brackets (provided) procured locally). and eight screws (provided, M3x10). 1. Turn off the power of the unit. EIA 19”... -
Page 10: Setting Up The Menu
SETTING UP THE MENU • Before the settings 1. Confirm that the cameras and peripherals are con- * MENU 1 OF 3 * nected correctly and firmly. 2. Turn on the power of this unit and connected peripherals. DYNAMIC REC ALARM BUZZER 1. -
Page 11: Setting Up Menu 1 Of 3 In Multiplex Mode
A. Setting up MENU 1 OF 3 in MULTISCR: Select this mode to monitor the camera pictures. MULTIPLEX mode In MULTISCR mode you can perform the following monitoring operations: The content of MENU 1 OF 3 in MULTIPLEX mode 1. Camera picture is as shown below. -
Page 12: Alarm Output
2. ALARM BUZZER 4. REC MODE The recording mode can be set to 4-255 fields or The buzzer beeps when this unit receives the alarm time lapse recording. signal. You can adjust the buzzer time between 1 1. Move the cursor to the REC MODE parameter. and 60 seconds by changing the ALARM BUZZER parameter. -
Page 13: Setting Up Menu 2 Of 3 In Multiplex Mode
B. Setting up MENU 2 OF 3 in 5. After selecting the first character, press button 12 (B B ). Then select the second character. MULTIPLEX mode 6. Repeat steps 3 to 5 above to complete the title. 7. Repeat steps 3 to 6 to edit the other channels. The context of MENU 2 OF 3 will not change if the 8. -
Page 14: Setting Up Menu 3 Of 3 In Multiplex Mode
3. TITLE DISPLAY C. Setting up MENU 3 OF 3 in This parameter lets you decide whether or not to MULTIPLEX mode have the title displayed. The content of MENU 3 OF 3 in MULTIPLEX mode 1. Move the cursor to the TITLE DISPLAY parameter. is as shown below. -
Page 15: Sequence Setup
3. SEQUENCE SETUP 4. START SCREEN This parameter lets you set the sequential order and This parameter lets you select a display pattern for dwell time for camera switching. your startup screen. When the power is turned on, 1. Move the cursor to SEQUENCE SETUP. the picture is displayed in the selected pattern. -
Page 16: Setting Up Menu 1 Of 3 In Multiscreen Mode
2. Press button 15 (SET). The CH SET menu appears A. Setting up MENU 1 OF 3 in on the monitor. MULTISCREEN mode ** CH SET ** 1. AUTO RESET This parameter lets you set the time until the unit 1 1CH recovers after receiving the alarm signal. -
Page 17: Setting Up Menu 2 Of 3 In Multiscreen Mode
B. Setting up MENU 2 OF 3 in 4. START SCREEN MULTISCREEN mode This item is the same as in MENU 3 OF 3 in MULTI- PLEX mode, although the parameters are different. MENU 2 OF 3 in the MULTISCR mode is the same 1. -
Page 18: Operation
OPERATION Before starting operation, set up the items in MENU 1-3 A. Single Spot Picture OF 3. 1. Set the MODE SELECT/CAMERA SELECT switch to CAMERA SELECT. Set SYSTEM MODE in MENU 3 OF 3 to MULTIPLEX or 2. Press one of the camera selection buttons for dis- MULTISCR depending on your specific needs. - Page 19 A. Single Spot Picture Recording on the Time Lapse VTR Confirm the REC MODE parameter. See page 9 for 1. Operate the VTR in playback mode. details. 2. Set the MODE SELECT / CAMERA SELECT switch Note: When T/L is selected but no camera switching to MODE SELECT.
- Page 20 B. Multi Spot Picture The LEDs on the camera selection buttons light to indicate the channels now displayed on the monitor First select a display pattern. screen. 1. Operate the VTR in playback mode. 2. Set the MODE SELECT/CAMERA SELECT switch to •...
- Page 21 C. Single Spot or Quad Playback Picture D. Still Playback Picture Sequences 1. Repeat procedures A (Single Spot Picture) or pro- 1. Repeat procedures A (Single Spot Picture) to moni- cedures B (Multi Spot Picture) to monitor playback tor a single spot playback picture or procedures B pictures.
- Page 22 Note: Two or more pictures on the monitor can be selected in multi picture mode. 6. Press the camera selection button whose indicator is blinking. The selected picture is displayed again for normal monitoring. 7. To release STILL ON mode, set the MODE SELECT/ CAMERA SELECT switch to MODE SELECT, then press button 16 (STILL ON).
-
Page 23: Multiscr Mode
MULTISCR Mode C. Single Spot or Quad Picture Sequences You can monitor sequential spot pictures or quad Select this mode to monitor the camera pictures. pictures. First select a display pattern. Selection of MULTISCR mode permits the following operations. To monitor sequential single spot pictures, take the same steps as described in procedures B for Monitoring the camera picture “Single Spot Picture Sequences of Monitoring... - Page 24 D. Still Multi Spot Picture E. Zoomed Multi Spot Picture The following function is available in multi spot The following function is available in multi spot picture mode only. picture mode only. 1. Set the MODE SELECT/CAMERA SELECT switch to 1.
-
Page 25: Connection
CONNECTION Refer to the operating instructions of each system component for connection and operation. Cameras Cameras Video Monitor Camera Drive Unit VIDEO INPUT VIDEO OUTPUT CAMERA CAMERA SW IN PLAY IN REC OUT MONITOR OUT CAMERA SIGNAL ALARM/REMOTE Cameras Time Lapse VTR VIDEO OUTPUT Note: The WV-80 cannot be used in this system. - Page 26 Power capacity of alarm output connector more • Connection with the Alarm Sensor than 100 mA: You can connect an alarm sensor to record the pic- tures of channels that receive alarm input signal. • Connect the buzzer through a relay circuit to Use an alarm sensor that meets the following con- pin 24 of the alarm output connector.
- Page 27 Connection with the Time Lapse VTR Connect the time lapse VTR as shown in the example below. Video Multiplexer WJ-FS216 CAMERA SW IN PLAY IN REC OUT ALARM/REMOTE 24 22 Time Lapse VTR VIDEO IN VIDEO OUT S-VIDEO AUDIO CAMERA SW OUT ALARM ALARM...
- Page 28 • Remote Control You can control the SEQUENCE, MULTISCREEN/QUAD SHIFT, and the camera selection buttons from a remote con- troller. These functions are activated by contact with the ground terminal (open collector output or normally open con- tact). • Connect the ALARM/REMOTE connector (pin 23) to the ground terminal as shown below. Switches 1 - 16 select the cameras (they do not control the alarm input).
-
Page 29: Specifications
SPECIFICATIONS Power Source: 220 - 240 V AC 50 Hz Power Consumption: 12 W Camera Input: 16 (BNC) 2:1 interlaced VBS 1.0V[p-p]/75 automatic termination/looping through Playback Input: 1 (BNC) VBS 1.0V[p-p]/75 Monitor Output: 1 (BNC) VBS 1.0V[p-p]/75 Recording Output: 1 (BNC) VBS 1.0V[p-p]/75 Camera Switching Input: 1 RCA pin jack Alarm Input:... - Page 30 Matsushita Electric Industrial Co., Ltd. Central P.O. Box 288, Osaka 530-91, Japan N0896-1117 YWV8QA4469BN Printed in Japan N 30 Gedruckt in Japan Imprimé au Japon Impreso en Japón...